通用串行总线(USB)数据传输模型

USB作为一种数据传输接口，了解它的通信传输机制是正确利用USB利用数据传输的基础，分层次结构对USB数据传输模型加以分析，可以使读者建立起USB体系结构、通信模型和总线事务的框架和概念，并最终对USB传输工作流程有一个清晰的认识。     

New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.     

新型水力泵排液工艺

酸化或压裂是改造油气层措施中常规的也是最有效的方法之一。问题是酸化或压裂结束后,采取何种工艺及时返排出残酸,减少残液二次沉淀对油层的污染。同时常规TCP(油管传输负压射孔)+DST(地层测试器)二联作测试工艺在遇到低压、低渗等非自喷油层时,要想取准油层产能、压力,收集到有代表性产液样品资料,困难很大。针对以上问题,大港油田钻采院研制了新型水力喷射泵,该泵可与酸化、压裂及射孔+测试等工艺配套使用,在实现一趟施工管柱同时完成几项工作的同时,利用喷射泵深抽、连续强排的技术特点,取得了较好效果。     

浅谈我国电信企业信息化策略

我国电信企业要做大做强，信息化是必然的战略选择和有效的助力器。本文阐述了电信企业信息化的含义、现状，描绘了电信企业信息化的目标，从经济学、管理学、行为科学等学科的角度提出了我国电信企业信息化策略。     

高峰值功率重频脉冲固体激光器

综述了高峰值功率重频脉冲固体激光器的发展现状，对其中的Ｑ开关、腔倒空、锁模等窄脉冲技术和放大技术进行了分析，展示了高峰值功率重频脉冲固体激光器的发展前景。     

Failure probability evaluation for normally distributed load-strength model with unknown parameters

The failure probability evaluation methods for load-strength interference model are established when both load, L, and strength, S, follow normal distributions, assuming none of the normal distribution parameters are known. Based on Fisher's fiducial analysis, a failure probability evaluation method is obtained for single load application. A numerical integration method is developed to evaluate the failure probability for multiple load applications.     

Accurate estimation of environment parameters from ultrasonic data

This paper describes a robust and accurate ultrasonic sensing system for a mobile robot. The system continuously updates a local map of the environment in which obstacles are represented by straight lines or points in a robot centered coordinate frame. The presented algorithms use a Kalman filter for the reduction of the noise in the ultrasonic data and use a systematical error correction (‘bundle correction’) to reduce the uncertainty in obstacle direction. Experiments are carried out in simulation and with a real mobile robot system. Results show that the accuracy with which line parameters can be estimated is in the order of 1 degree for the orientation and about 2 cm for the position. The effect of the bundle correction is significant and maximal when the robot approaches walls under a small angle.     

Statistical computer-aided design for microwave circuits

A useful methodology for microwave circuit design is presented. A statistical technique known as Design of Experiments is used in conjunction with computer-aided design (CAD) tools to obtain simple mathematical expressions for circuit responses. The response models can then be used to quantify response trade-offs, optimize designs, and minimize circuit variations. The use of this methodology puts the designer's intelligence back into design optimization while making “designing for circuit manufacturability” a more systematic and straightforward process. The method improves the design process, circuit performance, and manufacturability. Two design examples are presented in context to the new design methodology     

淀积条件对GDa—SiNx薄膜电学特性的影响

本文讨论了用辉光放电法制备氮化硅薄膜时衬底温度、射频功率和气体流量比对薄膜的电导率、介电常数和击穿强度的影响。通过优化生长条件，制备了优质非晶氮化硅薄膜，其介电常数为７．５、击穿强度为５．５ＭＶ／ｃｍ、电导率为１０－１３（Ωｃｍ）－１。