A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process     

CA／PAN中空纤维血浆分离膜的结构与性能

本研究以CA及PAN的共混溶液,通过干-湿法纺丝制取中空纤维,利用共混高聚物各组分在凝固剂中相分离速度的差异,形成具有稳定结构的中空纤维孔膜,该膜用于分离血液中的血浆成分具有良好效果。讨论了成型条件及添加剂等对膜结构、性能的影响,用SEM及图相分析仪、MAP压汞仪及DSC等分析手段,对膜的微孔结构、形态、孔尺寸及中空纤维膜的血浆通量和水通量等进行了系统的考查。     

BEM 系列原油流动性改进剂的应用

对BEM系列原油流动性改进剂的基本原理以及在中洛、濮临、东临、东黄、鲁宁、魏荆等几条原油长输管道工业应用的现场测试情况进行了介绍。结果表明，BEM系列原油流动性改进剂在降低原油凝点和粘度方面性能良好，能满足管道安全，平稳运行的要求。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

The zinc-rich corner of the Zn-Fe-Ni-Si quaternary system at 450 °C

Following up on recent studies of the Zn-rich corners of the Zn-Fe-Ni and Zn-Fe-Si ternary systems, a 450 °C isothermal section of the Zn-Fe-Ni-Si quaternary phase diagram with the Zn composition being fixed at 93 at.% was determined experimentally using optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive x-ray spectroscopy (EDS), and x-ray diffractometry (XRD). FeSi was found to be in equilibrium with almost all phases in the section, including the T, ζ, Ni-δ, NiSi₂, and FeSi₂ phases, as well as the liquid phase (L). Silicon solubilities in the T, ζ, and Ni-δ phases were rather limited. However, the solubilities of Fe and Zn in the NiSi₂ phase, at 4.5 at.% and 7.2 at.%, respectively, were appreciable. The existence of the (L+NiSi₂+Ni-δ) three-phase equilibrium state apparently prevents other Ni-Si compounds from entering equilibrium with the liquid at 450 °C. No true quaternary compound was found in the study.     

利用反射纵波评价裂缝倾角的模拟实验研究

声波全波列测井中的反射纵波可以用来评价高角度裂缝和对井周附近地质结构进行成像。目前的研究主要侧重于直接从波形资料处理出发计算裂缝的位置和倾角 ,其可靠性和准确性无从评价和校验。文中采用模拟实验的方法记录了倾角为 6 0°～80°范围内的 8种倾角裂缝的反射脉冲纵波波形 ,自行推导了反演裂缝倾角的公式 ,结合波场分离技术对实验测量波形数据进行了处理 ,计算出的裂缝倾角与实际值具有良好的一致性。本文结果表明 ,利用至少 2个深度点的纵波反射波波形资料就可以准确地反演裂缝的倾角     

孤岛油田西区聚合物驱开发研究

孤岛油田西区注聚区1997年3月投入注聚后，高渗层得到有效封堵，吸水剖面得到明显改善。注聚期间，通过实施注聚区外围水井降水或停注、油井放大生产压差和调整注聚井注入速度等开发措施，扩大了聚合物波及体积，聚合物驱取得了明显效果。     

Recovery of fluorocarbons in Japan as a measure for abating global warming

The objective of this study is to evaluate the potential for recovering fluorocarbons as measures for the abatement of global warming. In this study, we focused on the three different kinds of fluorocarbons: CFCs, HCFCs and HFCs, and targeted refrigerant use because of the availability of relevant data. We first estimated future fluorocarbon emissions from the targeted appliances; we next compared those emissions in the units of CO₂ equivalent to the level of CO₂ emissions in 1990 from a quantitative point of view. As the result of this study, it was found that fluorocarbon emissions in 1999 and 2010 would be equal to approximately 7 and 3% of the level of CO₂ emissions in 1990 respectively. Moreover, if we implement a 100% recovery rate in every recovery route, we can reduce a large amount of emissions which correspond to approximately 2–5% of the level of CO₂ emissions in 1990, even if we take into account the energy-related CO₂ emissions by the transportation and decomposition of fluorocarbons.     

C/O能谱测井数据预处理的两点改进意见

简单介绍了碳氧比测井的原理及通常的数据处理方法。分析了由常规数据处理所得曲线仍然存在的问题及可能的成因 ,并给出了可行的修正办法。讨论了另一种可行的曲线异常数据的检测、剔除方法。实践表明 :文章讨论的两点建议都是可行的 ,并且在提高测量曲线质量的同时也提高了地层含油饱和度的解释精度。