Fabrication of a new substrate for atomic force microscopic observation of DNA molecules from an ultrasmooth sapphire plate

A new stable substrate applicable to the observation of DNA molecules by atomic force microscopy (AFM) was fabricated from a ultrasmooth sapphire (alpha-Al2O3 single crystal) plate. The atomically ultrasmooth sapphire as obtained by high-temperature annealing has hydrophobic surfaces and could not be used for the AFM observation of DNA. However, sapphire treated with Na3PO4 aqueous solution exhibited a hydrophilic character while maintaining a smooth surface structure. The surface of the wet-treated sapphire was found by x-ray photoelectron spectroscopy and AFM to be approximately 0.3 nm. The hydrophilic surface character of the ultrasmooth sapphire plate made it easy for DNA molecules to adhere to the plate. Circular molecules of the plasmid DNA could be imaged by AFM on the hydrophilic ultrasmooth sapphire plate.     

Flexible generation mix under multi objectives and uncertainties

Criteria for evaluating flexibility of a generation mix are presented, and an efficient computational algorithm for determining a flexible generation mix considering uncertainties in the power system expansion planning is developed. The flexible generation mix problem is formulated as a multiobjective optimization problem and solved by the dynamic programming technique in which type of generation plant is selected as a stage and generation capacity is selected as a state. The proposed method can treat easily not only the uncertainties but also many constraints of generation planning such as integer solutions of generation capacities, reliability constraints, and so on. The effectiveness and feasibility of the proposed method are demonstrated on a typical power system model     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

A new method of automatic polishing on curved aluminium alloy surfaces at constant pressure

This paper presents original research results of automatic polishing on curved surfaces of aluminium alloy moulds at constant pressure. The automatic polishing of aluminium alloy material is achieved. A parameter S is defined, which can express the comprehensive influential factors in the automatic polishing process and give a relationship among the polishing quality and the various machining variables. Based on this, a new method for comprehensive control of polishing quality is suggested.     

Studies on the silver/silver oxide electrode

The electrochemical behaviour of silver/silver oxides electrodes in 1 N KOH or 1 N KOH + methanol have been studied by measuring current-potential and impedance-potential curves under the potential sweep in the cathodic direction starting from the AgO formation region.Two specific anodic current peaks A and X were observed in current-potential curves. It was concluded that X was due to the incomplete oxidation of Ag₂O to AgO under the anodic sweep or due to the partial decomposition of AgO layer, and A was due to the catalytic reaction of AgO with methanol followed by the electrochemical oxidation of Ag₂O to AgO.The values of the impedance tend to decrease in the vicinity of the peak A at the low frequency, which may be attributed to the reduction of AgO with methanol.     

Ring hydrogenation of naphthalene and 1-naphthol over supported metal catalysts in supercritical carbon dioxide solvent

Catalytic ring hydrogenations of naphthalene and 1-naphthol were studied over several supported metal catalysts in supercritical carbon dioxide solvent at low temperature. Higher concentration of hydrogen in supercritical carbon dioxide and lower reaction temperature were responsible for higher catalyst activity and selectivities to the desired partial ring hydrogenated products as compared with those observed in organic solvent for the same catalyst.     

Highly Reactive β-Dicalcium Silicate: III, Hydration Behavior at 40–80°C

The effect of curing temperature (40°, 60°, 80°C) on the hydration behavior of β-dicalcium silicate (β-C₂S) was investigated. The β-C₂S was obtained by decomposition of hillebrandite, Ca₂(SiO₃)(OH)₂, at 600°C, has a specific surface area of about 7 m²/g, and is in the form of fibrous crystals. The dependence of the hydration reaction on temperature continues until the reaction is completed. The hydration is completed in 1 day at 80°C and in 14 days at 14°C. The hydration mechanism is different above and below 60°C, but at a given temperature, the reaction mechanism and the silicate anion structures of C-S-H do not change significantly from the initial to the late stages of the reaction. High curing temperature and long curing times after completion of reaction promote silicate polymerization. The Ca/Si ratio of C-S-H shows high values, being almost 2.0 above 60°C and 1.95 below 40°C.     

Recoverable shear strain of liquid crystal‐forming concentrated hydroxypropyl cellulose solutions

The recoverable shear strain (S_R) for the liquid crystal‐forming hydroxypropyl cellulose solutions was determined by means of a concentric cylinder rotational apparatus as functions of shear stress prior to recovery and concentration of the solutions at 30°C. S_R greatly depended on shear stress and concentration; the phase of the solution (the single phase or biphase) governed the dependences of S_R on stress and concentration. S_R increased with increasing stress for the single phase and decreased for the biphase. S_R seemed to be related to the die swell (B): S_R ∝ Bⁿ. S_R exhibited a maximum and a minimum with respect to concentration. S_R for the cellulosic cholesteric liquid crystalline solutions was greater than that for the isotropic solutions. A model was proposed for explaining the greater S_R. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 865–872, 2002     

In Situ Observation of Zirconia Particles at 1200°C by High-Resolution Electron Microscopy

Zirconia (ZrO₂) particles (average diameter, 30 nm) were observed in an in situ heating experiment up to 1200°C using a 400-kV high-resolution electron microscope. Thermal vibration of atoms on a (001) surface plane was observed at 1100°C. At 1200°C, grain growth and sintering phenomena were recorded on a videotape, showing (100) lattice planes migrating on a surface of a particle. Direct observation of the sintering process on a lattice level was accomplished for the first time.     

The effect of sputter etching on the surface characteristics of dyed aramid fabrics

Three kinds of aramid fabrics, Technora (modified p-aramid), Conex (m-aramid) and Kevlar (p-aramid), were subjected to sputter etching and argon low-temperature plasma treatments after dyeing in black with disperse dyes. The depth of shade increased considerably on Technora and Kevlar with the sputter etching treatment, but not on Conex fabrics. Argon low-temperature plasma treatment had virtually no effect on the depth of shade on the aramid fabrics.