Fine Patterning and Characterization of Gel Films Derived from Methyltriethoxysilane and Tetraethoxysilane

Pregrooves of 1.6 µm pitch for optical data storage have been embossed successfully by pressing a stamper against x CH₃Si(OC₂H₅)₃(100 - x )Si(OC₂H₅)₄-derived gel films (60 ≤ x ≤ 100 mol%) on glass-disk substrates of 130 mm diameter. When x is <40 mol%, the resultant films are too hard to emboss patterns uniformly. The shrinkage of the patterns is ∼4% for all the films when 60 lessthan equal to x lessthan equal to 100 mol%, even after heat treatment at 350°C, so that the nearly net negative shape of the stamper is preserved. The methyl groups in the films decompose at temperatures from 500° to 600°C.     

Structural Changes of Scandia-Doped Zirconia Solid Solutions: Rietveld Analysis and Raman Scattering

Powder X-ray diffractometry (XRD) and Raman scattering measurements were used to study the structural changes of compositionally homogeneous metastable ZrO₂ solid solutions induced by ScO_1.5 doping. The crystal structures of monoclinic, tetragonal, cubic, and rhombohedral (Sc₂Zr₇O₁₇, ß-phase) solid-solution phases have been refined by using the Rietveld analysis of the XRD data at room temperature of arc-melted ZrO₂- X ScO_1.5 ( X = 0, 2, …, 20, and 22 mol%) samples. The results can be interpreted as indicating that the structures of the monoclinic and tetragonal phases approach those of the tetragonal and cubic phases, respectively, by ScO_1.5 doping. Raman scattering, as well as XRD, was useful to investigate the phase assemblage. Moreover, we could obtain Raman spectra of the ß-phase probably for the first time.     

Rolling contact fatigue of alumina ceramics sprayed on steel roller under pure rolling contact condition

The rolling contact fatigue of sprayed alumina ceramics with a nominal composition of Al₂O₃–2.3 mass% TiO₂ was studied with a two-roller test machine under a pure rolling contact condition with oil lubricant. The influence of undercoating of sprayed Ni-based alloy on the rolling contact fatigue was investigated. The failure mode of all sprayed rollers was spalling caused by subsurface cracking. The undercoating did not contribute to the improvement of the rolling contact fatigue life. The elastic modulus of the alumina sprayed layer evaluated with the nano-indentation method was around 85 GPa. The depths of the observed subsurface cracks corresponded approximately to the depths where the orthogonal shear stress or the maximum shear stress calculated with two-dimensional FEM became maximum.     

Simulation of ultrasonic-vibration drawing using the finite element method (FEM)

In ultrasonic-vibration drawing, wires are drawn while ultrasonic vibration is applied to a drawing die. Prior studies provide experimental proof that ultrasonic-vibration drawing reduces drawing resistance, improves lubrication and prevents wire breakage. In the future, ultrasonic-vibration drawing is expected to contribute to the drawing of difficult-to-draw materials and operations, such as shaped wires, ultrafine wires, and the wire drawing operation in semidry or dry condition. However, a detailed analysis and understanding of the mechanism of improvement is not possible on the basis of conventional experimental observations because the ultrasonic-vibration processing phenomenon occurs at high speed. Therefore, we attempted to understand the processing mechanism of ultrasonic-vibration drawing using the finite element method (FEM). ABAQUS was used for the FEM. Drawing force and stress–strain distributions in drawn wires were analyzed. From these studies, we quantitatively clarified the mechanism of improved drawing characteristics, such as decreased drawing force.     

Hydrothermal corrosion of TiN PVD films on SUS-304

Hydrothermal corrosion of thin TiN PVD films (3 μm thickness) at 100 MPa water and 20-800 °C temperature range was studied. Noticeable oxidation starts above 200 °C and acceleration of oxidation processes takes place in hydrothermal conditions in comparison with airflow oxidation of corresponding PVD films and air oxidation of TiN powders. The formation of Ti_nO_2n−1 homological series phases and regular single crystals in oxide scale were observed. FeTiO₃ ilmenite layer secures high protective properties at 600 °C and practically does not contain chromium. Therefore, usual low alloy steel with TiN coating can be used instead superalloy for wet air oxidation system with working temperature up to 600 °C.     

Coagulation mechanism of salt solution-extracted active component in Moringa oleifera seeds

This study focuses on the coagulation mechanism by the purified coagulant solution (MOC-SC-PC) with the coagulation active component extracted from M. oleifera seeds using salt solution. The addition of MOC-SC-PC tap water formed insoluble matters. This formation was responsible for kaolin coagulation. On the other hand, insoluble matters were not formed when the MOC-SC-PC was added into distilled water. The formation was affected by Ca2+ or other bivalent cations which may connect each molecule of the active coagulation component in MOC-SC-PC and form a net-like structure. The coagulation mechanism of MOC-SC-PC seemed to be an enmeshment of Kaolin by the insoluble matters with the net-like structure. In case of Ca2+ ion (bivalent cations), at least 0.2 mM was necessary for coagulation at 0.3 mgC l-1 dose of MOC-SC-PC. Other coagulation mechanisms like compression of double layer, interparticle bridging or charge neutralization were not responsible for the coagulation by MOC-SC-PC.     

Computer-aided design of a factor Xa inhibitor by using MCSS functionality maps and a CAVEAT linker search

We have investigated a new approach to efficiently find a novel inhibitor against a serine protease (i.e. an activated coagulation factor X, FXa) by using de novo design programs and the X-ray crystal structure of the target enzyme. FXa is a coagulant enzyme that generates thrombin (a serine protease) and participates in both intrinsic and extrinsic coagulation pathways. We adopted multiple copy simultaneous search (MCSS) and CAVEAT linker search techniques, which disclosed a novel FXa inhibitor (T01312) consisting of two binding moieties (the benzamidinyl and adamantyl groups) and a linker unit (the carboxybenzylamine group). The inhibitory activity of T01312 against FXa was determined to be a small K(i)-value of 48nM, which is two orders of magnitude smaller than that against thrombin. An X-ray crystal analysis of T01312 complexed with trypsin (an analogue of FXa) and docking studies of T01312 with trypsin and FXa showed that: (i) the benzamidinyl group is a predominant binding moiety in the anionic pocket (S1 site) with an asparatic acid residue; (ii) a hydrophobic pocket (S4 site) is the binding site of the adamantyl group; (iii) the carboxylate group of the linker contributes to the selectivity for FXa against thrombin. Thus, the combination of the knowledge of the X-ray crystal structure of the target molecule with MCSS and CAVEAT linker search techniques proved to be an effective hit-finding method that does not require the screening of huge compound libraries.     

Hot-water treatment of sol–gel derived SiO2–TiO2 microparticles and application to electrophoretic deposition for thick films

SiO₂–TiO₂ spherical microparticles of about 0.7 μm in diameter were prepared by the sol–gel method. Anatase nanocrystals were formed in the microparticles and their specific surface area was increased after a hot-water treatment at 90 °C. From the changes in the concentration of I₂ photocatalytically generated from KI aqueous solution, the activity of the SiO₂–TiO₂ microparticles was found to increase with increasing the hot-water treatment time. Particulate, thick films were electrophoretically deposited on indium tin oxide (ITO)-coated glass substrates using the anatase nanocrystal-precipitated SiO₂–TiO₂ microparticles. The thickness of the electrophoretically deposited particulate film increased to be approximately 10 μm with an increase in applied voltage. The resultant thick film showed a high photocatalytic activity.     

GeoVISTA Studio: a codeless visual programming environment for geoscientific data analysis and visualization

The fundamental goal of the GeoVISTA Studio project is to improve geoscientific analysis by providing an environment that operationally integrates a wide range of analysis activities, including those both computationally and visually based. Improving the infrastructure used in analysis has far-reaching potential to better integrate human-based and computationally based expertise, and so ultimately improve scientific outcomes. To address these challenges, some difficult system design and software engineering problems must be overcome.This paper illustrates the design of a component-oriented system, GeoVISTA Studio, as a means to overcome such difficulties by using state-of-the-art component-based software engineering techniques. Advantages described include: ease of program construction (visual programming), an open (non-proprietary) architecture, simple component-based integration and advanced deployment methods. This versatility has the potential to change the nature of systems development for the geosciences, providing better mechanisms to coordinate complex functionality, and as a consequence, to improve analysis by closer integration of software tools and better engagement of the human expert. Two example applications are presented to illustrate the potential of the Studio environment for exploring and better understanding large, complex geographical datasets and for supporting complex visual and computational analysis.     

Parallel processing circuit of line image using neuristor

A simultaneous detecting circuit system of centers and lengths of some lines in one dimension is presented applying an electronic circuit model of the nervous axon with respect to signal transmission. This model consists of series of one basic section, and has functions of Neuristor. The circuit system has a paralell processing function. It is constructed by three layers. In the first layer each visual signal of lines is changed to electric pulse signal. In the second layer edges of each line are detected, and in the third layer these detected signals are converted into voltages which correspond to lengths of the lines. These functions were confirmed experimentally using its hardware.