EFFECT OF INTERMITTENT HEATING ON DRYING-INDUCED STRAIN-STRESS OF MOLDED CLAY

Parametric analyses of the strain-stress in the drying process are performed to study the influence of the intermittent drying on the behaviors of drying-induced strain-stress and deformation as well as the drying characteristic. The transient three-dimensional problem of strain-stress and heat and moisture transfer in a slab is solved simultaneously by the finite element method. The dimensionless parameters are introduced to generalize the problem in the conservation equations of heat and moisture transfer. The intermittent drying is modeled by applying periodically smaller and larger Biot numbers to the boundary conditions. The maximum tensile and compressive stresses fluctuate, and fall remarkably during the smaller Biot number period when a slab is heated intermittently. The peak stress of the fluctuation exceeds beyond the case in the continuous healing where the overall drying rate is almost equivalent to that in the intermittent beating, but the reduction of the stresses takes place rapidly in the low heating period.     

Photocatalytic activity of transparent porous glass supported TiO2

A porous glass tube with a composition of 96SiO₂·4B₂O₃ (wt%) supported TiO₂ shows high photooxidation activity due to its transparency and large surface area. The surface area of the porous glass tube supported TiO₂ is 10,000 times larger than that of conventional materials. TiO₂ crystals supported are anatase type. Transparency of the porous glass tube is very important. Herein, sol–gel and chemical vapor deposition (CVD) processes were employed as TiO₂ supporting processes. CVD process is more effective. For instance, an aqueous methylene blue solution with 1 ppm concentration almost thoroughly decomposes at a contact time of 300 s using porous glass tube supported TiO₂ prepared by CVD process under irradiating with 10 W low-pressure mercury lamp, on the other hand, opaque porous alumina tube supported TiO₂ was only 25%. The smaller the pore size of the porous glass tube, the larger the transparency and the permeation resistance through porous glass tube. Hence, porous glass tube with ca. 40 nm pore diameter is suitable from the standpoint of a practical use.     

A Bayesian evaluation of simulation models of multiple-site fatigue cracks

The rivet holes along the longitudinal top row of the outer skin of the fuselage over a two-bay length are considered as the independent structural unit for the simulated multiple-site fatigue cracks. Models of multiple-site fatigue cracks are proposed. The models are divided into several phases with some uncertain parameters. These phases are incorporated sequentially into a computer code with the Monte Carlo simulation method. The Bayesian estimation of uncertain parameters in the model can be identified on visual inspections by the Bayesian procedure from in-service inspection data measuring crack lengths of each rivet hole. In summary, this study evaluates effects of differences in the simulation models for the crack coalescence and failure phase for the distribution of inspection data measuring crack lengths with the Bayesian estimation of uncertain parameters from simulated in-service inspection data.     

Photocurrent in and miscibility of poly(N-vinylcarbazole)/poly(methyl methacrylate) blends

Summary Steady-state photocurrent in poly(N-vinylcarbazole)(PVCz) (26,48 wt%)/poly(methyl methacrylate)(PMMA) blends is for the first time measured. The PVCz(26,48 wt%)/PMMA blends showed almost the same carrier-generation efficiencies at electric fields higher than 1 × 10⁵ V · cm⁻¹. The results are explained by high miscibility of the PVCz(26,48 wt%)/PMMA blends, suggesting the existence of PVCz chains in continous PMMA-rich phase in the phase-separated structure. The miscibility is also evaluated by means of excimer fluorescence of PVCz in these blends and fluorescence microscopy. Received: 26 December 2000/Revised version: 16 January 2001/Accepted: 19 January 2001     

Cube-type micro SOFC stacks using sub-millimeter tubular SOFCs

Fabrication and characterization of tubular SOFCs under sub-millimeter (0.8 mm), bundles and stacks for low temperature operation were shown. The materials used in this study were Gd doped CeO₂ (GDC) for electrolyte, NiO–GDC for anode and (La, Sr)(Co, Fe)O₃ (LSCF)–GDC for cathode, respectively, and LSCF for supports of the tubular cells for bundle fabrication. After applying a sealing layer and current collector for each bundle of five micro tubular SOFCs, each bundle was stacked vertically, to build a four-storey cube-type stack with volume of about 0.8 cm³. The performance of the stack was shown to be 3.6 V OCV and 2 W maximum output power under 500 °C operating temperature. Preliminary quick start-up test was also conducted at the condition of 3 min start-up time from 150 to 400 °C for 5 times, and the results showed no degradation of the performance during the test.     

Microstructural Interpretation on Reliquefaction of Saturated Granular Soils under Cyclic Loading

It is well known that the resistance to liquefaction of a saturated sand decreases sharply when it has been presheared, either cyclically or quasi statically, beyond a threshold value. The possible mechanism is discussed in light of recent findings on the microstructural anisotropy developed in preshearing (induced anisotropy). A columnlike structure, through which applied stress is mainly transmitted, grows parallel to the major principal stress direction in the strain hardening process. Voids, randomly distributed at first, are also connected in series between the columnlike structures. The anisotropic structure can carry the increasing stress as long as the major stress is applied parallel to the elongation direction of the structure. However, it becomes extremely unstable when the major stress is rotated. The excess pore-water pressure increases markedly under undrained cyclic loading, particularly when the connected voids are stressed perpendicular to their elongation direction. This is the reason why once liquefied sand sharply loses liquefaction resistance in a subsequent reliquefaction test.     

Construction of a reporter yeast strain to detect estrogen receptor signaling through aryl hydrocarbon receptor activation

The activation mechanism of estrogen receptor (ER) signaling by association with the aryl hydrocarbon receptor (AhR) was elucidated recently (Ohtake, et al., Nature 2003, 423, 545). In the present study, we established a reporter yeast strain to evaluate this ER signaling by association with the activated AhR. This yeast strain expresses human ER and AhR, and has a reporter plasmid with estrogen response elements. With this yeast strain we assayed ER activation by various AhR ligands, i.e., 2,3,7,8-tetrachlorodibenzo-p-dioxin, benzo[a]pyrene, 3-methylcholanthrene, beta-naphthoflavone, and indirubin. All these ligands induced ER activation dose-dependently and their EC50 values were 60, 180, 130, 26, and 0.5 nM, respectively. Then, we measured the activity in water collected at 5 localities in the Ishizu River system in Japan. The activities of water samples ranged from 4.8 pmol/L (1.3 ng/L) to 52 pmol/L (14 ng/ L) (17beta-estradiol (E2) equivalent). These values were higher than those measured with the yeast for ER activation through direct ligand binding to ER. The direct ER ligand binding activities of the water samples ranged from 2.5 to 5.3 pmol/L (E2 equivalent). We also measured AhR activation of the water samples using a reporter yeast for AhR ligand activity. The activities ranged from 102 to 472 pmol/L (beta-naphthoflavone equivalent). These results indicate that the water samples contain substances that bind to AhR, and these substances contribute to ER signaling through AhR activation in the yeast reporter strain. This yeast reporter strain should be a useful tool to evaluate direct and indirect ER activation by environmental samples.     

Development research on composite adsorbents applied in adsorption heat pump

A novel adsorbent design technique base on the concept of Kelvin equation was proposed to develop hydrophilic adsorbent applicable to water vapor adsorption heat pump (AHP) for high performance. In the process, the composite adsorbent was prepared after silica gel was synthesized in the pores of activated carbons by impregnating activated carbons in sodium silicate solution. Two kinds of activated carbons were tested to produce composite adsorbent and to investigate the performance by measuring the adsorption isotherms of water vapor and pore structure characteristics. All adsorption isotherms of the silica impregnated activated carbons prepared shifted to a lower region of water vapor pressure compared to those of the raw activated carbons. The volume-based amount of adsorption in the AHP operation range (φ = 0.1–0.4) for the adsorbents prepared at sodium silicate solution concentration of 10 wt.% and impregnating time of 48 h are 5.88 and 2.62 times that of the raw activated carbons (AC1 and AC2), respectively. Based on the Kelvin equation, it is clarified that the contact angle and the volume of pore radius greater than 1.2 nm decrease with the increase of sodium silicate solution concentration for the novel composite adsorbents, which contributes the isothermals shift to lower relative pressure range.     

Ubiquitous user authentication system with wireless battery‐powered fingerprint identification module

This paper describes a ubiquitous user authentication system consisting of a wireless fingerprint identification module and service‐providing equipment that offers services to the user. Users carry their own module and the user can activate the module only by identifying the fingerprint. The wireless communication between the activated module and the equipment enables continuous user authentication. This authentication certifies not only the presence but also the absence of the genuine user. The identification module was built with a fingerprint identification LSI (FIL) that senses and identifies fingerprints on a single‐chip. The LSI makes a small, light, battery‐powered tamper‐proof module possible. Two applications of the system were devised with the module. The experimental results demonstrate that the system authenticates the users continuously. The proposed system achieves ubiquitous user authentication which enables the authentication of the user anytime, anywhere. Copyright © 2007 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A 60-MHz 240-mW MPEG-4 videophone LSI with 16-Mb embedded DRAM

A 240-mW single-chip MPEG-4 videophone LSI with a 16-Mb embedded DRAM is fabricated utilizing a 0.25-μm CMOS triple-well quad-metal technology. The videophone LSI is applied to the 3GPP 3G-324M video-telephony standard for IMT-2000, and implements the MPEG-4 video SPL1 codec, the AMR speech codec, and the ITU-T H.223 Annex B multiplexing/demultiplexing at the same time. Three 16-bit multimedia-extended RISC processors, dedicated hardware accelerators, and a 16-Mb embedded DRAM are integrated on a 10.84 mm×10.84 mm die. It also integrates camera, display, audio, and network interfaces required for a mobile video-phone terminal. In addition to conventional low-power techniques, such as clock gating and parallel operation, some new low-power techniques are also employed. These include an embedded DRAM with optimized configuration, a low-power motion estimator, and the adoption of the variable-threshold voltage CMOS (VT-CMOS). The MPEG-4 videophone LSI consumes 240 mW at 60 MHz, which is only 22% of that for a conventional multichip design. Variable threshold voltage CMOS reduces standby leakage current to 26 μA, which is only 17% of that for the conventional CMOS design