Preparation and characterization of foamed polyurethane/silicone rubber/graphite nanocomposite as radio frequency wave absorbing material: The role of interfacial compatibilization

A novel method for the preparation of radio frequency (RF) wave absorber polyurethane foam (PU) has been developed by impregnation of PU foam in n-hexane solution of room temperature vulcanizing (RTV) silicone rubber (SR) hybridized with graphite nanosheets (GNs) called doping solution. Extent of the GNs dispersion was optimized by the incorporation of a specific type of bifunctional compatibilizer. Insulator to conductive transition threshold as well as electromagnetic wave absorption characteristics of the fabricated nanocomposites was shown to be dependent upon the compatibilizer functionality. All PU/SR/GN nanocomposites generated from bifunctional compatibilizer exhibited higher electrical conductivity with enhanced permittivity implying enhanced formation of conductive networks by GN platelets. Permittivity of the PU/SR/GN nanocomposite based on bifunctional compatibilizer showed to be higher than uncompatibilized counterpart. Electromagnetic reflection loss behavior of the PU/SR/GN nanocomposites exhibited a non-linear correlation with the electrical conductivity. Although all PU/SR/GN prepared nanocomposites exhibited electromagnetic wave reflection loss behavior, but this revealed to be affected by the GN level as well as the size and dispersion state of the graphite nanosheets.     

A Sliding Mode Controller Based on Robust Model Reference Adaptive Proportional-integral Control for Stand-alone Three-phase Inverter

This paper proposes a sliding mode controller based on robust model reference adaptive proportional-integral (RMRA-PI) control for a stand-alone voltage source inverter (SA-VSI). The proposed controller has two control loops where the coefficients of PI controller are regulated by the adaptive sliding law. This method is used to regulate the output voltage of the inverter under different load conditions and uncertainty, and adapts the output to the reference model to reduce the total harmonic distortion (THD). In this paper, the stability of the proposed controller is proven by using Lyapunov’s theory and Barbalet’s lemma. The proposed controller performs well in voltage regulation such as low THD under sudden load change and uncertainty. Also, the results of the proposed controller are compared with PI controller to show the effectiveness of the presented control system.     

Insight into the Impact of Oxidative Stress on the Barrier Properties of Lipid Bilayer Models

As a new field of oxidative stress-based therapy, cold physical plasma is a promising tool for several biomedical applications due to its potential to create a broad diversity of reactive oxygen and nitrogen species (RONS). Although proposed, the impact of plasma-derived RONS on the cell membrane lipids and properties is not fully understood. For this purpose, the changes in the lipid bilayer functionality under oxidative stress generated by an argon plasma jet (kINPen) were investigated by electrochemical techniques. In addition, liquid chromatography-tandem mass spectrometry was employed to analyze the plasma-induced modifications on the model lipids. Various asymmetric bilayers mimicking the structure and properties of the erythrocyte cell membrane were transferred onto a gold electrode surface by Langmuir-Blodgett/Langmuir-Schaefer deposition techniques. A strong impact of cholesterol on membrane permeabilization by plasma-derived species was revealed. Moreover, the maintenance of the barrier properties is influenced by the chemical composition of the head group. Mainly the head group size and its hydrogen bonding capacities are relevant, and phosphatidylcholines are significantly more susceptible than phosphatidylserines and other lipid classes, underlining the high relevance of this lipid class in membrane dynamics and cell physiology.     

Modeling metallurgical responses of coal Tri-Flo separators by a novel BNN:a "Conscious-Lab" development

Tri-flo cyclone,as a dense-medium separation device,is one of the most typical environmentally friendly industrial techniques in the coal washery plants.Surpris...     

Fluid Flow and Mixing in Non-Isothermal Water Model of Continuous Casting Tundish

Fluid flow and mixing of molten steel in a twin-slab-strand continuous casting tundish were investigated using a mixing model under non-isothermal conditions.This model led to a set of ordinary differential equations that were solved with a Runge-Kutta algorithm.Steady state water modeling was carried out under non-isothermal conditions.Experimental data obtained from the water model were used to calibrate the mixing model.Owing to the presence of a mixed convection in the non-isothermal conditions,a channelizing flow would be created in the fluid inside the tundish.A mixing model was designed that was capable of predicting RTD（residence time distribution）curves for different cases in non-isothermal conditions.The relationship between RTD parameters and the Tu（tundish Richardson number）was obtained for various cases under non-isothermal conditions.The results show that the RTD parameters were completely different under isothermal and non-isothermal conditions.The comparison of the RTD curves between the isothermal and non-isothermal conditions presents that the extent of mixing in the tundish in non-isothermal conditions is lower than the mixing extent in isothermal conditions.     

辊速差对连铸连轧7075铝板显微组织、 织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响.采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验.结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5％和21.9％.此外,当辊...     

Camelid Single-Domain Antibodies: Promises and Challenges as Lifesaving Treatments

Since the discovery of camelid heavy-chain antibodies in 1993, there has been tremendous excitement for these antibody domains (VHHs/sdAbs/nanobodies) as research tools, diagnostics, and therapeutics. Commercially, several patents were granted to pioneering research groups in Belgium and the Netherlands between 1996–2001. Ablynx was established in 2001 with the aim of exploring the therapeutic applications and development of nanobody drugs. Extensive efforts over two decades at Ablynx led to the first approved nanobody drug, caplacizumab (Cablivi) by the EMA and FDA (2018–2019) for the treatment of rare blood clotting disorders in adults with acquired thrombotic thrombocytopenic purpura (TPP). The relatively long development time between camelid sdAb discovery and their entry into the market reflects the novelty of the approach, together with intellectual property restrictions and freedom-to-operate issues. The approval of the first sdAb drug, together with the expiration of key patents, may open a new horizon for the emergence of camelid sdAbs as mainstream biotherapeutics in the years to come. It remains to be seen if nanobody-based drugs will be cheaper than traditional antibodies. In this review, I provide critical perspectives on camelid sdAbs and present the promises and challenges to their widespread adoption as diagnostic and therapeutic agents.     

An experimental evaluation of cross-layer routing in a wireless mesh backbone

Over the latest few years, cross-layer design in wireless networks has drawn great attention from the research community. One of the main arguments in favor of such techniques is that the hop-count metric alone is not enough to capture the specificities of wireless links (e.g., interferences, collisions, fading). In this paper, we address a simple yet fundamental question: What are the real improvements that cross-layering can bring to routing performance when compared to the simple hop-count metric? In our experiments, we consider the backbone of a real wireless mesh network composed of 12 routers deployed in an office building. We focus on the stability of routes and their persistence. In spite of the nature of cross-layer metrics that take into account information from different layers, lets them be very reactive to changes, we observe that using these metrics, pairs of nodes tend to mainly use the same set of two or three routes between them.