Comparison of liquid-phase and methanol-swelling crosslinking processes of polyimide dense membrane for CO2/CH4 separation

To overcome the plasticization effect in polyimide membranes, many researchers have proposed crosslinking method. This can reduce an inter-segmental mobility by tightening and rigidifying the polymer chains. However, it is difficult to modify the whole polymer chains throughout the membrane because the reaction can be hindered by the diffusion rate of the crosslinker. In particular, it is hard for bulky crosslinker to penetrate a dense membrane with a small d-spacing. This study investigated the effect of crosslinking a dense Matrimid membrane with p-phenylenediamine (p-PDA) via two different crosslinking methods (i.e., methanol-swelling crosslinking process [M-SCP] and liquid-phase crosslinking process [L-PCP]). Most of the crosslinking reaction in M-SCP occurs on the membrane surface due to difficulty in penetration of the bulky p-PDA into the Matrimid dense membrane. In contrast, the L-PCP allows uniform crosslinking across the membrane. The membranes crosslinked using L-PCP showed excellent chemical resistance. Furthermore, the plasticization phenomenon was not observed in the membranes crosslinked using L-PCP with p-PDA more than 15%. Meanwhile, the membrane crosslinked using M-SCP exhibited poor plasticization and chemical resistance properties. These results showed that the L-PCP method can be more effective for the crosslinking of dense membrane to deliver both high plasticization and chemical resistance.     

光储微网系统多目标协调控制策略

基于光伏储能+电采暖的光储微网系统可以有效解决西部农村社区清洁能源供应量不足问题.为了提高光储微网系统的能量控制效果和工程实用性能,该文通过构建包含电力费用、储能系统荷电状态(SOC)、供暖舒适度等变量的多目标函数,提出一种计算量较低的储能与电热负荷多目标协调控制策略.为了简化目标函数求解过程,引入求导和单调性分析等优化方法.为了降低系统计算量,以住宅建筑保温性能为评价标准,提出一种带宽能量控制模式,降低了被控单元的控制频率,提高了算法的工程应用价值.搭建Matlab/Simulink仿真平台,依据西部青海省某示范光储微网系统实际数据,仿真对比分析基于传统能量控制策略和基于多目标协调控制策略的光储微网系统性能,验证该文所提控制策略的有效性和优越性.     

Superplastic deformation and crystallization behavior of Cu54Ni6Zr22Ti18 metallic-glass sheet

Superplastic deformation and crystallization behavior of a Cu₅₄Ni₆Zr₂₂Ti₁₈ metallic glass were investigated. A maximum elongation of 650% was obtained at 733 K at 1 × 10⁻² s⁻¹ from the sheet fabricated by squeeze copper-mold casting method. At low strain rates, the strain-rate-sensitivity exponent value was close to 1, suggesting that Newtonian-like behavior governed the plastic flow. At a high strain rate around 10⁻² s⁻¹, a transition from Newtonian to non-Newtonian behavior took place with decrease in m value. Large strain hardening by crystallization occurred during the course of deformation. The strain hardening was found to be caused by crystallization according to the analyses of the relation of true stress vs. testing time, T-T-T diagram and DSC characteristics. The time periods up to the strain before strain hardening at 733 K for the Cu₅₄Ni₆Zr₂₂Ti₁₈ metallic glass were similar to that of the Zr₆₅Al₁₀Ni₁₀Cu₁₅ metallic glass at 696 K as 180–300 s (3–5 min). This coincidence could be explained by comparison of their T-T-T diagrams showing that the incubation times for crystallization of the Cu BMG at 733 K and for Zr BMG at 696 K are similar.     

Densification and compressive strength ofin-situ processed Ti/TiB composites by powder metallurgy

In the present study, the densification of Ti/TiB composites, the growth behavior ofin-situ formed TiB reinforcement, the effects of processing variables — such as reactant powder (TiB₂, B₄C), sintering temperature and time — on the microstructures and the mechanical properties ofin-situ processed Ti/TiB composites have been investigated. Mixtures of TiB₂ or B₄C powder with pure titanium powder were compacted and presintered at 700°C for 1 hr followed by sintering at 900, 1000, 1100, 1200, and 1300°C, respectively, for 3hrs. Some specimens were sintered at 1000°C for various times in order to study the formation behavior of TiB reinforcementin-situ formed within the pure Ti matrix. TiB reinforcements were formed through different mechanisms, such as the formation of fine TiB and the formation of coarse TiB by Ostwald ripening or the coalescence of fine TiB. There was no crystallographic relationship between TiB reinforcement and the matrix. There were voids at the interface between the TiB reinforcement and the Ti matrix due to the preferential growth of coarse TiB without a particular crystallographic relationship with pure Ti matrix and the surface energy between the Ti matrix and TiB reinforcements. Therefore, the densification of Ti/TiB₂ compacts was hindered by the preferential growth of coarse TiB reinforcements. The mechanical properties ofin-situ processed composites were evaluated by measuring the compressive yield strength at ambient and high temperatures. The compressive yield strength of thein situ processed composites was higher than that of the Ti-6A1-4V alloy. It was also found that the compressive yield strength of the composite made from TiB₂ reactant powder was higher than that of the composite made from B₄C at the same volume fraction of reinforcement. A crack path examination suggested that the bonding nature of interface between matrix and reinforcement made from TiB₂ reactant powder was better than that made from B₄C.     

EFFECT OF LASER SCANNING SPEED ON PHASE CONSTITUTION AND WEAR RESISTANCE OF LASER CLADDING HARD FACING ALLOY STELLITE 12

Effect of laser scanning speed on phase constitution,microstructure,microhardness and wearresistance of laser-cladding hard facing alloy Stellite 12 has been investigated by means of across-flow-type CO_2 laser of 1.5 kW.The laser-cladding layer on the alloy consists of ma-trix phase of suppersaturated solid solution γ(Co,Cr)and complex hexagonal carbideM_7C_3.Under certain condition,at higher laser scanning speed,the suppersaturated solubilityof elements increases in γ(Co,Cr),and the precipitation of the complex carbtde M_7C_3 de-creases,so the microhardness increases and the wear resistance decreases.But at slower laserscanning speed,more complex carbide M_7C_3 may precipitate,and the wear resistance may beimproved.Therefore,it is believed that the principal factor in improving wear resistance is theprecipitation of carbide M_7C_3,while increment of microhardness is the suppersaturated solu-bility of elements in matrix phase γ(Co,Cr).     

基于压电晶体的高效电能转换设备设计

为了高效地利用风能和雨能，设计了通过压电传感器组件a将风或雨的能量转换为电能的装置。该装置可为负载和蓄电池供电，它的分辨力高，即使是弱风和小雨产生的微压也能进行电能转换。当压电晶体板d或e受压时，小齿轮顺时针或逆时针旋转；当压电晶体b或c受压时，液压缸伸长或收缩。在液压缸和小齿轮的作用下，压电晶体板a所在平面的法线自动调整到正好与风和雨的方向一致，从而增大了电能转化率。     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Quantum teleportation between a single-rail single-photon qubit and a coherent-state qubit using hybrid entanglement under decoherence effects

We study quantum teleportation between two different types of optical qubits using hybrid entanglement as a quantum channel under decoherence effects. One type of qubit employs the vacuum and single-photon states for the basis, called a single-rail single-photon qubit, and the other utilizes coherent states of opposite phases. We find that teleportation from a single-rail single-photon qubit to a coherent-state qubit is better than the opposite direction in terms of fidelity and success probability. We compare our results with those using a different type of hybrid entanglement between a polarized single-photon qubit and a coherent state.     

Formation stabilization and resizing based on the control of inter‐agent distances

We propose a control strategy that could steer the group of mobile agents in the plane to achieve a specified formation. The control law could be implemented in a fully decentralized manner so that each agent moves on their own local reference frame. Under the acyclic minimally persistent graph topology, each agent measures the relative displacements of neighboring agents and then adjusts the distances between them to achieve the desired formation. As well as achieving a fixed formation, we could resize the formation only by changing the leader edge, which connects the leader with the first‐follower in acyclic minimally persistent graph, without changing the structures of the control law. Copyright © 2014 John Wiley & Sons, Ltd.     

Exploring the Relationship Between Green Consumption Value,Satisfaction, and Loyalty to Hybrid Car in Elderly Consumers

The study aimed to examine the relationship between green consumption value, satisfaction, and loyalty of driving hybrid cars among elderly consumers. Data were collected from a cross‐sectional survey of 314 elderly consumers who purchased hybrid cars in the United States. A partial least squares analysis revealed that elderly consumers’ social, price, and quality values positively influenced the satisfaction of their hybrid car experience, and their satisfaction significantly influenced their loyalty of hybrid car. The relationship between green consumption value, satisfaction, and loyalty toward driving hybrid cars among elderly consumers revealed insight into their value orientations toward the hybrid car. Special efforts are suggested in promoting hybrid car use to elderly consumer groups. Marketers should pay attention to changing beliefs and increasing perceived values of driving a hybrid car for consumers to encourage them to use green products.