X-ray CDF study on the behaviour of the amorphous chain under extension

The behaviour of the amorphous chain in vulcanized natural rubber (NR) and styrene-butadiene rubber (SBR) under extension is studied by means of the cylindrical distribution function (CDF) derived from wide angle X-ray scattering (WAXS). In the case of the highly stretched vulcanized NR where the orientation-induced crystallization took place, the observed WAXS intensity was separated into a crystalline peak component and a broad amorphous one from which the CDF was obtained. The CDF calculated from the broad component shows that some of the amorphous segments of the highly stretched vulcanized NR are extended as fully as the crystalline chains and that the fraction of the segments increases with increasing extension. In the case of SBR, such fully stretched segments as in the case of the vulcanized NR show higher degree of an interchain packing order than those in the vulcanized NR.     

Residual Stress in Siliceous Glass Between Mullite Crystals

A birefringence of siliceous glass, which is coexisting with mullite crystals, was studied by an optical polarizing microscope. The cause of the birefringence was assumed to be the residual stress induced by a large contraction difference between the mullite and glass on cooling. The stress has been evaluated to be as high as—0.3 GPa, and to correspond to the elastic one which began to develop at the glass transition point.     

Synthesis of terpene alcohols from isoprene oligomers

Various terpene alcohols were prepared from isoprene oligomers via two steps: epoxidation with peracetic acid and isomerisation with aluminium triisopropoxide. For example, 2-methylene-6-methyl-7-octene-1-o1 was prepared from 2,6-dimethyl-1,7-octadiene. From 2,6-dimethyl-2,7-octadiene, 3,3,6-trimethyl-1,5-heptadiene, 2,7-dimethyl-2,6-octadiene, 2,6-dimethyl-1,3,6-octatriene, 1-methyl-4-isopropenyl-1-cyclohexene, and 1,5-dimethyl-1,5-cyclooctadiene, the corresponding alcohols were obtained, respectively.     

Effect of Silicon Dioxide on the Thermal Diffusivity of Aluminum Nitride Ceramics

The thermal diffusivity of AlN ceramics was significantly decreased by the addition of SiO₂. The AlN ceramics with 4 wt% SiO₂ could not be densified by pressureless sintering in the temperature range 1400° to 1800°C. The thermal diffusivity of these samples was very low because of their porous structure. The AlN ceramics containing 2, 4, and 8 wt% SiO₂ were densified by hot-pressing and also had low thermal diffusivity. In these samples, the grains of the 27R polytype that resulted from the reaction between AlN and SiO₂ were dispersed, obstructing the conduction of heat. The relation between the amount of 27R polytype and the thermal diffusivity of the AlN ceramics was determined.     

Fibrous support for immobilization of enzymes

A poly(vinyl alcohol) (PVA) fiber support incorporating various aminoacetal functional groups has been developed for immobilizing enzymes. The aminated PVA fiber seems to adsorb enzymes with electrostatic force of attraction; thus the immobilization procedure is simple. By the use of this fiber having immobilized enzymes, the reaction between enzymes and substrates is nearly independent of the size of subtstrates. This newly developed type of fiber, which is formed by a mass superfine fibers (SFF), each measuring 1 μm or less in diameter, permits much more increased surface area than the conventional enzyme immobilization supports. Our studies of the properties of the fiber for immobilization of enzymes show the following results: (1) SFF has a greater ability for the immobilization of invertase than ordinary fibers; (2) dimethyl-aminated SFF has the best performance for the immobilization of invertase. From these results, it is concluded that the dimethyl-aminated SFF is an excellent support for the immobilization of invertase.     

Local disturbances preceding a running crack front in a viscoelastic solid

The local disturbances ahead of a running crack front in a viscoelastic solid were measured through noncontact electro-optical tools. It was observed that the very high local strain rate up to 200/sec exists even in the present quasistatic loading case. It may be concluded that the running crack propagation velocities, not the conventional average strain rates ranging from about 10^?4/sec to 10^?2/sec, govern the local disturbances, as the crack propagation velocities always exceed 200m/sec for both average strain rates, while the local strain rates observed do not show much differences between both average strain rate cases.     

Liquefaction of wood in the presence of phenol using phosphoric acid as a catalyst and the flow properties of the liquefied wood

The liquefaction of wood in the presence of phenol using phosphoric acid as a catalyst and the flow properties of the obtained liquefied wood were investigated. It was found that phosphoric acid is a satisfactory catalyst for liquefying wood. The amount of phenol that reacts with the liquefied wood components (i.e., combined phenol) increases with an increase in liquefaction temperature, liquefaction time, catalyst content, or liquid ratio. By removing the free phenol, the resulting liquefied woods become novolaclike resins. The measurements of the flow properties of these liquefied woods reveal that the melts of liquefied woods behave as pseudoplastics and their flows obey the Ostwald de Waele power law equation. The amount of combined phenol within the liquefied wood and the presence of filler in the liquefied wood have great influence on their flow properties. The flowing temperature, activation energy, and zero shear viscosity of the liquefied woods show tendencies to increase with an increase in combined phenol. © 1994 John Wiley & Sons, Inc.     

Prooxidant effects of inorganic chromium compounds in the autoxidation of methyl linoleate

The prooxidant property of inorganic chromium compounds was determined in methyl linoleate free from natural antioxidants and metals. Prooxidant properties of inorganic chromium compounds appeared in order of sodium chromate > chromium (VI)-oxide > chromium chloride > potassium chromate > chromium (III)-oxide > potassium dichomate. In comparison with the control, additions of chromium compounds induced different amounts of autoxidation products derived from methyl linoleate, such as small amounts of hydroperoxides and conjugated dienes and large amounts of hydroxy groups,α,β,γ,δ-unsaturated carbonyls, isolatedtrans double bonds, polymers, and free radicals. From these analytical data, the catalysis of chromium compounds in the autoxidation of methyl linoleate seemed to be based on their abilities of abstracting a hydrogen from methyl linoleate and decomposing hydroperoxides derived from the autoxidation of methyl linoleate.     

Shear-rate dependence of first normal stress difference of poly(isoprene-b-styrene) in solution near the order-disorder transition temperature

Viscoelastic properties of poly(isoprene-b-styrene) in dioctylphthalate under steady shear flow were measured near the order—disorder transition temperature. In ordered states, first normal stress difference N₁ is proportional to shear rate at low region, but becomes proportional to at the high region, similar to the N₁ behaviour of polymer blends undergoing shear-induced homogenization. Because the existence of microdomains was confirmed at the high region by the flow birefringence method, it is concluded that the above N₁ behaviour is not caused by shear-induced homogenization, but is probably caused by the shear-induced alignment of the microdomain structure.     

An Application of Silica‐Based Monolithic Membrane Emulsification Technique for Easy and Efficient Preparation of Uniformly Sized Polymer Particles

Summary: Uniformly sized polymer particles were prepared by an emulsification and polymerization technique utilizing a silica monolithic membrane, namely the “silica monolithic membrane emulsification technique”. In this paper, we utilized silica monolithic membrane as a device for the preparation of uniformly sized polymer particles. A mixture of monomers, diluents and oil‐soluble initiator was emulsified into a continuous medium through the silica monolithic membrane and polymerized. The particles obtained had a higher size uniformity than that of particles prepared by previously reported membrane emulsification techniques, such as the Shirasu Porous Glass (SPG) emulsification technique. Through the silica monolithic membrane emulsification technique, we could prepare particles having availability as a possible packing material for solid‐phase extraction (SPE) and high performance liquid chromatography (HPLC).

SEM photograph of silica particles prepared through capillary plate membrane.