液动旋冲接头冲击功测试方法研究

液动旋冲接头性能参数是旋冲接头设计的主要依据之一，如何对液动旋冲接头的参数进行检测是非常重要的工作。在分析和比较了测试液动旋冲接头性能参数各种方法的基础上，选择了冲击力法来进行破岩液动旋冲接头的性能参数测试，以YD系列测力传感器为检测元件，建立了一套比较完善的自动检测系统。分析了影响单次冲击功测试的因素，得出了测试旋冲接头的性能参数的影响规律。     

Designing circuits with partial scan

In this scan design methodology, only selected faults are targeted for detection. These faults are those not detected by the designer's functional vectors. The test generator decides exactly which flip-flops should be scanned using one of two methods. In the first method, all possible tests are generated for each target fault, and the set of tests requiring the fewest flip-flops is selected. In the second method, only one test is generated for each fault, and the use of flip-flops is avoided as much as possible during test generation. Examples of actual VLSI circuits show a savings of at least a 40% in full-scan overhead     

Radiation of millimeter waves from NRD leaky wave antennas withtapered transition and tuning aperture

The radiation of millimeter waves from the nonradiative dielectric (NRD) leaky wave antennas with the tapered transition and the tuning aperture is investigated. An accurate theory for the leakage constant and the phase constant of the antennas is presented, which is based on the generalized scattering parameters considering the higher-order mode interactions at the discontinuities. The associated transverse equivalent network involves the characterization of the mode couplings at two air-to-dielectric interfaces, the coupled mode analysis of the tapered transition, and the calculation of the radiation fields at the tuning aperture via the extended spectral domain approach. The interesting behavior of the present modified configuration of NRD leaky wave antennas is illustrated by typical examples. The validity of the theory is confirmed by the comparison of the theoretical results with experimental data for the limiting cases     

宣钢烧结生产配加钢渣的工业试验

总结了宣钢烧结配配加钢渣生产不同碱度烧结矿的工业生产试验，提出了配加钢渣可强化全精粉烧结。     

MX345芯片及单片机控制

MX345芯片用于产生模拟信令—CTCSS单音.本文在介绍MX345编码/解码器工作原理的基础上,设计出MX345芯片与单片机的接口电路.最后给出控制软件.     

油田热采注汽管道在线检测技术现状

稠油热采注汽管道由于长期在高温、高压下运行,极易发生各种损伤,如腐蚀、裂纹、材料退化等,极易造成管道承压能力降低,发生失效事故。如何检测出潜在危险性缺陷,判断注汽管道能否继续使用,是保证注汽管道安全运行的关键问题。探讨了高温压力管道在线检测技术发展现状及其应用范围。     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

Synthesis,characterization, and redox and electrochromic behaviors of poly(3-n-octyloxythiophene)

Poly(3-n-octyloxythiophene), a conjugated polymer, which possessed solubility in common organic solvents, was synthesized by electrochemical polymerization in the presence of lithium perchlorate as the supporting electrolyte and sodium dodecyl sulfate as the surfactant in an aqueous medium. Characterizations of the intermediate, monomer, and polymer were performed by NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, and gel permeation chromatography. The process of electrochemical polymerization and the electrochemical redox behaviors were investigated by cyclic voltammetry and the potentiostatic method. A poly(3-n-octyloxythiophene) film that was deposited on a platinum electrode was found to exhibit electrochromic behaviors, and it switched electrochemically between blue–green oxidized and dark red reduced states. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

"JDS-音频化渣微机综合检测系统"的应用与效果

简要介绍“JDS-音频化渣微机综合检测系统”的工作原理和应用效果，证明使用该装置是提高炼钢操作水平的一条较好途径。     

CO毒化AB5型合金分形特征研究

研究了三种贮氢合金 L a Ni5、L a Ni4 .7Al0 .3、Ml Ni4 .5Al0 .5被 10 0× 10 - 6 CO毒化后的分形特征 ,求出这三种合金在含 10 0× 10 - 6 CO的氢中循环 ,分维分别为 0 .2 5 4 7、0 .170 9、0 .0 72 5。可以较好的解释合金被毒化的宏观现象。