Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.     

YSZ/MoS2 self-lubricating coating fabricated by thermal spraying and hydrothermal reaction

Thermal sprayed ceramic coatings have extensively been used in components to protect them against friction and wear. However, the poor lubricating ability severely limits their application. Herein, yttria-stabilized zirconia (YSZ)/MoS₂ composite coatings were successfully fabricated on steel substrate with the combination of thermal spraying technology and hydrothermal reaction. Results show that the synthetic MoS₂ powders are composed of numbers of ultra-thin sheets (about 7 ~ 8?nm), and the sheet has obvious lamellar structure. After vacuum impregnation and hydrothermal reaction, numbers of MoS₂ powders, look like flowers, generate inside the plasma sprayed YSZ coating. Moreover, the growing point of the MoS₂ flower is the intrinsic micro-pores of YSZ coating. The friction and wear tests under high vacuum environment indicate that the composite coating has an extremely long lifetime (>?100,000 cycles) and possesses a low friction coefficient less than 0.1, which is lower by about 0.15 times than that of YSZ coating. Meanwhile, the composite shows an extremely low wear rate (2.30?×?10^?7 mm³ N^?1 m^?1) and causes slight wear damage to the counterpart. The excellent lubricant and wear-resistant ability are attributed to the formation of MoS₂ transfer films and the ultra-smooth of the worn surfaces of hybrid coatings.     

液压支架让缩性能试验特性分析与探讨

分析研究国家标准中液压支架让缩性能试验的技术要求,设计开发让缩性能试验系统,以双伸缩立柱液压支架为研究对象进行让缩性能试验分析与研究,为让缩性能试验的开展提供了试验条件,为液压支架国标的实施提供基础。     

复合材料在旋转压缩机上的应用分析

文章介绍了目前旋转式压缩机主要零部件的材料状况,详细论述了金属基复合材料、陶瓷基复合材料在旋转压缩机上的应用情况及前景,为复合材料在压缩机领域的应用提供指导。     

Theoretical Prediction of Chiral 3D Hybrid Organic–Inorganic Perovskites

Hybrid organic–inorganic perovskites (HOIPs), in particular 3D HOIPs, have demonstrated remarkable properties, including ultralong charge‐carrier diffusion lengths, high dielectric constants, low trap densities, tunable absorption and emission wavelengths, strong spin–orbit coupling, and large Rashba splitting. These superior properties have generated intensive research interest in HOIPs for high‐performance optoelectronics and spintronics. Here, 3D hybrid organic–inorganic perovskites that implant chirality through introducing the chiral methylammonium cation are demonstrated. Based on structural optimization, phonon spectra, formation energy, and ab initio molecular dynamics simulations, it is found that the chirality of the chiral cations can be successfully transferred to the framework of 3D HOIPs, and the resulting 3D chiral HOIPs are both kinetically and thermodynamically stable. Combining chirality with the impressive optical, electrical, and spintronic properties of 3D perovskites, 3D chiral perovskites is of great interest in the fields of piezoelectricity, pyroelectricity, ferroelectricity, topological quantum engineering, circularly polarized optoelectronics, and spintronics.     

A novel method based on convolutional neural networks for deriving standard 12-lead ECG from serial 3-lead ECG

Frontiers of Information Technology & Electronic Engineering - Reconstruction of a 12-lead electrocardiogram (ECG) from a serial 3-lead ECG has been researched in the past to satisfy the need...     

On Cost Aware Cloudlet Placement for Mobile Edge Computing

As accessing computing resources from the remote cloud inherently incurs high end-to-end (E2E) delay for mobile users, cloudlets, which are deployed at the edge of a network, can potentially mitigate this problem. Although some research works focus on allocating workloads among cloudlets, the cloudlet placement aiming to minimize the deployment cost (i.e., consisting of both the cloudlet cost and average E2E delay cost) has not been addressed effectively so far. The locations and number of cloudlets have a crucial impact on both the cloudlet cost in the network and average E2E delay of users. Therefore, in this paper, we propose the Cost Aware cloudlet PlAcement in moBiLe Edge computing (CAPABLE) strategy, where both the cloudlet cost and average E2E delay are considered in the cloudlet placement. To solve this problem, a Lagrangian heuristic algorithm is developed to achieve the suboptimal solution. After cloudlets are placed in the network, we also design a workload allocation scheme to minimize the E2E delay between users and their cloudlets by considering the user mobility. The performance of CAPABLE has been validated by extensive simulations.      

Imaging of two-dimensional unsaturated moisture flows in uncracked and cracked cement-based materials using electrical capacitance tomography

The development of visualizing tools to monitor unsaturated moisture flow in cement-based materials is of great importance, as most degradation processes in cement-based materials are connected to and take place in the presence moisture. This paper investigates the ability of electrical capacitance tomography (ECT) to image two-dimensional (2D) unsaturated moisture flow in cement-based materials. In ECT, the electrical permittivity distribution within an object is reconstructed based on measured capacitances between electrodes attached on the object’s surface. In a series of experiments, mortar specimens with and without discrete cracks were imaged with ECT during a 2D moisture ingress. The results show that ECT is able to monitor the evolution of the moisture flow, and to approximate the shape and position of the moisture front. These findings indicate that ECT is a viable method for monitoring and visualizing 2D unsaturated moisture flow in cement-based materials in the presence and absence of discrete cracks.