Call control and traffic transport for connection-oriented highspeed wireless personal communications over metropolitan area networks

A distributed circuit-switched approach for supporting the deployment of high speed wireless personal communication services in urban areas through the interconnection of base stations via metropolitan area networks (MANs) is proposed. Broadband MANs minimize traffic congestion by dynamic sharing of link capacity and by serving as distributed switches for partitioning call control functions. While the DQDB protocol readily supports distributed packet-switching over the IEEE 802.6 MAN, isochronous traffic such as voice and video is best supported by circuit-switched connections. The authors present an enhanced bi-state pre-arbitrated (PA) transport mechanism, and associated call control and handoff management techniques, which enable distributed circuit-switching over the MAN. These capabilities are not currently addressed in the 802.6 standards. The bi-state PA transport mechanism facilitates statistical multiplexing of variable rate isochronous traffic sources. The network capacity is constrained by the call setup delay performance, and is analyzed by simulations. Alternative signaling architectures, involving different placements of call control network elements, are evaluated. The effects of erasure nodes, and close bus versus open bus architectures, are considered. The overlap inter-MAN call setup procedure is proposed to reduce delays. Different call handoff procedures are formulated according to the type of handoff and the resulting change in call connectivity. Most handoffs are intra-MAN, requiring simple procedures with short delays     

Error monitoring issues for common channel signaling

Motivated by field data which showed a large number of link changeovers and incidences of link oscillations between in-service and out-of-service states in common channel signalling (CCS) networks, a number of analyses of the link error monitoring procedures in the SS7 protocol were performed by the authors. This paper summarizes the results obtained thus far and include the following: (a) results of an exact analysis of the performance of the error monitoring procedures under both random and bursty errors; (b) a demonstration that there exists a range of error rates within which the error monitoring procedures of SS7 may induce frequent changeovers and changebacks; (c) an analysis of the performance of the SS7 level-2 transmission protocol to determine the tolerable error rates within which the delay requirements can be met; (d) a demonstration that the tolerable error rate depends strongly on various link and traffic characteristics, thereby implying that a single set of error monitor parameters will not work well in all situations; and (e) some recommendations on a customizable/adaptable scheme of error monitoring with a discussion on their implementability. These issues may be particularly relevant in the presence of anticipated increases in SS7 traffic due to widespread deployment of advanced intelligent network (AIN) and personal communications service (PCS) as well as for developing procedures for high-speed SS7 links currently under consideration by standards bodies     

Focusing characteristics of a wide-striped laser diode integratedwith a microlens

We developed a wide-striped laser diode integrated with a microlens that provides good focusing characteristics through a small focusing spot. We calculated and demonstrated that a 60-μm-wide core and a 1.9-μm-high ridge is the best structure for fundamental index-guiding mode oscillation of a wide-striped laser diode. We integrated a wide-striped laser diode with the developed microlens in the Fresnel diffraction held, and demonstrated that a device with a 60-μm-wide core has a minimum focusing spot width of 2.0 μm in the horizontal direction. Also, we estimated the wavefront in the Fresnel diffraction field from the working distance error of a lens designed for a collimated incident beam, and showed that the working distance error, focusing spot width, and sidelobe can be improved by this estimated wavefront     

Resonant couplers acting as add-drop filters made withsilica-on-silicon waveguide technology

Add-drop filters are demonstrated using silica-on-silicon optical waveguide technology. This device consists of a full directional coupler subdivided by Mach-Zehnder sections. Tapering of the coupling coefficients is experimentally shown to dramatically reduce the filters' sidelobes. Only one photolithographic step is required using the silica planar waveguide technology, yielding accurate wavelength control of the filters. Excellent agreement between measurement and design was achieved     

Evaluation of absorption and emission cross sections of Er-dopedLiNbO3 for application to integrated optic amplifiers

The polarization-dependent absorption and emission spectra of the ⁴I_13/2-⁴I_15/2 transition (λ~1.5 μm) in single crystal bulk Er:LiNbO₃ have been measured. Low-temperature (10 K) measurements of the Stark split energy levels of these two manifolds indicate at least two Er³⁺ sites. McCumber theory is applied to determine the Er:LiNbO₃ absorption and emission cross sections. These values are used to calculate the gain characteristics of Er:LiNbO₃ channel waveguides. Calculations indicate that a gain of 10 dB is achievable in a waveguide of several centimeters using ~20-mW pump power     

Dynamic range of coherent analog fiber-optic links

We investigate the performance of coherent analog optical links employing amplitude modulation (AM), phase modulation (PM), and frequency modulation (FM). The performance of these coherent links is compared to that of AM direct-detection (DD) links. The signal-to-noise ratios, nonlinearities, and-spurious-free dynamic ranges (SFDR's) of the foregoing links are evaluated. We calculate the SFDR for links using DFB and Nd:YAG lasers with typical linewidths of 10 MHz and 5 kHz, respectively. The performance of PM and FM links is dominated by phase noise above a critical value of received optical power. For a linewidth of 10 MHz, and SFDR's of PM and FM links are 30 and 31 dB, respectively, for a received optical power above -27 dBm in a 1 GHz bandwidth. For a linewidth of 5 kHz, the corresponding SFDR's above a received power level of 0 dBm are 51 and 53 dB. The performance of DD and AM links is dominated by RIN above a critical value of received optical power. For a RIN level of -155 dB/Hz, the SFDR's of DD and AM links are 49 and 47 dB, respectively, for a received optical power of 10 dBm in a 1 GHz bandwidth. The SFDR's of the DD and coherent links used for transmission of subcarrier-multiplexed (SCM) signals are also derived. We evaluate target laser parameters needed by a number of different applications. For AM video and antenna remoting applications, linewidths of <1 and <3 kHz are required to use PM and FM links, respectively. For FM video, linewidths of <150 and <350 MHz are required to use PM and FM links. For SCM digital applications, linewidths of <80 and <200 MHz are required to use PM and FM links. The paper concludes with a discussion of system implementation issues, including linearization, optical frequency modulation, balanced receivers, and IF issues     

Computationally efficient methods for bit-error rate evaluation inweakly coherent optical systems

A semianalytical method to estimate the bit-error rate performance of nonsynchronous ASK and FSK optical heterodyne systems is presented. This approach takes into account numerous system details with an accuracy similar to Monte-Carlo simulation, but with a computation time reduced by several orders of magnitude. An analytical approximation, based on a closed-form expression for the decision variable moment generating function, is also presented. The results obtained with the semianalytical method and the analytical approximation are compared to Monte-Carlo simulation results and to measurements obtained on a practical FSK system     

A time domain approach for avoiding crosstalk in optical blockingmultistage interconnection networks

Crosstalk in multistage interconnection networks can be avoided by ensuring that a switch is not used by two connections simultaneously, in order to support crosstalk-free communications among N inputs and N outputs, a space domain approach dilates an N×N network into one that is essentially equivalent to a 2N×2N network. Path conflicts, however may still exist in dilated networks. This paper proposes a time domain approach for avoiding crosstalk. Such an approach can be regarded as “dilating” a network in time, instead of space. More specifically, the connections that need to use the same switch are established during different time slots. This way, path conflicts are automatically avoided. The time domain dilation is useful for overcoming the limits on the network size while utilizing the high bandwidth of optical interconnects. We study the set of permutations whose crosstalk-free connections can be established in just two time slots using the time domain approach. While the space domain approach trades hardware complexity for crosstalk-free communications, the time domain approach trades time complexity. We compare the proposed time domain to the space domain approach by analyzing the tradeoffs involved in these two approaches     

P-N double quantum well resonant interband tunneling diode withpeak-to-valley current ratio of 144 at room temperature

The current-voltage characteristics of the P-N double quantum well resonant interband tunneling (RIT) diodes in InAlAs-InGaAs system have been improved in this letter. The peak-to-valley current ratio (PVCR) is as high as 144 at room temperature. As we know, this is the highest room temperature PVCR ever reported in any tunneling devices. Moreover, the influence of the central barrier thickness varying from 10 Å to 30 Å on the device characteristics is also studied     

Similarity, interactive activation, and mapping.

The question of "What makes things seem similar?" is important both for the pivotal role of similarity in theories of cognition and for an intrinsic interest in how people make comparisons. Similarity frequently involves more than listing the features of the things to be compared and comparing the lists for overlap. Often, the parts of one thing must be aligned or placed in correspondence with the parts of the other. The quantitative model with the best overall fit to human data assumes an interactive activation process whereby correspondences between the parts of compared things mutually and concurrently influence each other. An essential aspect of this model is that matching and mismatching features influence similarity more if they belong to parts that are placed in correspondence. In turn, parts are placed in correspondence if they have many features in common and if they are consistent with other developing correspondences. (PsycINFO Database Record (c) 2010 APA, all rights reserved)