Syntheses of Spinon Thermal Conductivity Materials in Sr–Cu–O System by Glass‐Ceramics Technique

We have synthesized spinon thermal conductivity materials in Sr–Cu–O system by glass‐ceramics technique. The materials are promising for active control of thermal energy in microelectronic devices because of high and anisotropic thermal conduction, its controllability, and electric insulation. Nevertheless, research on these materials has been limited to that concerning theoretical perspectives and investigation of physical properties using large single crystals. In this study, we adopt glass‐ceramics technique to synthesize these materials: We prepared melt‐quenched multicomponent oxides including SrO and CuO, and checked its glass‐forming ability and crystallization behaviors by heating. As a result, we have found that SrCuO₂ and Sr₁₄Cu₂₄O₄₁, known as the spinon thermal conductivity materials, are synthesized using SrO–CuO–?Li₂O–?Al₂O₃?–Ga₂O₃ system. This synthesis process for the system will provide practical application of the spinon thermal conductivity materials.     

Crystallographic Texture Development in Bismuth Sodium Titanate Prepared by Reactive-Templated Grain Growth Method

Bi_0.5Na_0.5TiO₃ (BNT) and 0.94Bi_0.5Na_0.5TiO₃·0.06BaTiO₃ (BNT–BT) bulk ceramics with extensive 〈100〉 texture were prepared by the reactive-templated grain growth method, using platelike Bi₄Ti₃O₁₂ (BIT) particles as templates for BNT. Calcined compacts were composed of matrix grains with random orientation and 〈100〉-oriented grains transformed from aligned BIT particles, and the texture developed by the growth of oriented grains during sintering. Ceramics with extensive texture were obtained by using the starting mixture containing the maximum concentration of platelike BIT to form the maximum volume fraction of oriented grains.     

Continuous emulsion polymerization of styrene in a single Couette–Taylor vortex flow reactor

The effect of the geometrical and operational parameters on the mixing characteristics of a Couette–Taylor vortex flow reactor (CTVFR) were investigated and were correlated with the same parameters by using the tank‐in‐series model. Continuous emulsion polymerization of styrene was conducted at 50°C in a CTVFR to clarify the effects on kinetic behavior and reactor performance of operational parameters such as rotational speed of inner cylinder (Taylor number), reactor mean residence time, and emulsifier and initiator concentrations in the feed streams. It was found that steady‐state monomer conversion and particle number could be freely varied only by varying the Taylor number. In order to explain the observed kinetic behavior of this polymerization system, a mathematical model was developed by combining the empirical correlation of the mixing characteristics of a CTVFR and a previously proposed kinetic model for the continuous emulsion polymerization of styrene in continuous stirred tank reactors connected in series (CSTRs). On the basis of these experimental results, it was concluded that a CTVFR is suitable for the first reactor (prereactor) of a continuous emulsion polymerization reactor system. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1931–1942, 2001     

Measurement of internal stresses in coatings using time resolved fluorescence

This paper describes a new nondestructive technique for detecting internal stresses in coatings using time resolved fluorescence. The measurement principle is based upon an experimental result that the decay time of fluorescence from poly(3-octylthiophene), P3OT, dispersed in uniaxially-stretched polymer films decreases with increasing tensile stress acting on the films. Internal stresses in the clear coat and in the base coat of a multilayer structure, which was composed of electrodeposited coat, surface coat, base coat, and clear coat, were estimated from the decay time of fluorescence from P3OT in both coats. The order of internal stresses in the clear coat and base coat of the multilayer system was 1 MPa. When the coatings were piled up, the internal stress decreased as the distance from a metal substrate was increased. It was found that moisture and temperature influenced internal stresses in the clear coat rather than in the base coat. Internal stress in the clear coat, which was one layer coated on a metal substrate, was measured by the traditional bimetallic method or by the time resolved fluorescence technique. Comparing both methods, it was concluded that the time resolved fluorescence technique gave reliable values for internal stresses in coatings.     

Effects of acid strength and micro pore size on -caprolactam selectivity and catalyst deactivation in vapor phase Beckmann rearrangement over acid solid catalysts

The vapor phase Beckmann rearrangement of cyclohexanone oxime (CHO) over solid acid catalysts including zeolites was carried out to elucidate the effects of the acid strength and the micropore size of the catalysts on the selectivity of -caprolactam (CL) and the catalyst deactivation rate. It was found that the catalyst deactivation rate was strongly dependent on the acid strength of the acid catalysts. The improvement of catalyst life was achieved by using MFI-type metallosilicates having weak acid sites. The CL selectivity decreased over the acid catalysts with micropores larger than those of the MFI zeolites. Furthermore, using methanol and carbon dioxide as the diluent solvent and diluent gas improved CL selectivity and catalyst life, respectively.     

Aerosol-to-liquid collection: A method for making aqueous suspension of hydrophobic nanomaterial without adding dispersant

This article introduces an aerosol-based technique to make aqueous suspension of hydrophobic nanomaterial without adding dispersant. The method is intended for making a test-sample for evaluating the toxicities of nanomaterial by intra-tracheal administration. The method can wet the surface of hydrophobic nanomaterial within a few seconds. After the wetting process five to ten minutes of sonication assisted with manual stirring can fully disperse the hydrophobic nanomaterials in water. Two types of TiO₂ nanomaterial were used in this study; Tayca JMT-150IB whose surfaces are coated with negatively charged hydrophobic functional group, and P25 whose surfaces are naturally hydrophilic. Nanomaterials are aerosolized by a dry-method and become micrometer-sized agglomerates. Then supersaturated water vapor is condensed onto these airborne agglomerates by using a growth tube collector. The collected suspension (CS) of hydrophobic nanomaterial (JMT-150IB) is prepared in two steps; airborne agglomerates are collected onto a flat surface then transferred to liquid-water and subsequently sonicated for complete dispersion. This method works equally well for making the CS of hydrophilic nanomaterial. Size distribution measurements of the CS show that airborne agglomerates of TiO₂ dissociate into smaller units of agglomerates once they are captured into water, and the sizes of the agglomerates are in the nanometer to sub-micrometer range. Light scattering technique is used to show that a short sonication process can reproduce the particle number concentration of the CS after long storage.

Copyright © 2017 American Association for Aerosol Research     

Molecular simulation and experimental studies of the miscibility of polylactic acid/polyethylene glycol blends

Computer simulation and experiments were performed to investigate the miscibility of PLA/PEG blends with different PEG concentrations. Flory-Huggins interaction (χ) parameter used to predict the miscibility for the blends was estimated by molecular dynamic simulation of fully atomistic model. The calculated χ parameter and radial distribution function suggest that the PLA and PEG blends are likely miscible at low PEG concentrations (10–30 wt%), but they become apparently immiscible at higher PEG content (>50 wt%). This result is consistent with density distribution of PLA and PEG beads calculated from dissipative particle dynamics simulation of coarse-grained model. To support the computational results, experiments based on differential scanning calorimetry (DSC) and rheometry were also performed. The DSC thermograms of 90:10, 80:20, and 70:30 (wt/wt) of PLA/PEG blends showed a single glass transition and PLA melting peak, indicating PLA/PEG is miscible over this composition. In rheometry, frequency (ω) dependence of storage moduli (G′) at low frequencies for 75:25 and 70:30 blends indicate that these samples are near the phase separation point.     

Microwave dielectric properties and crystal structures of Mg0.7Al2.2O4 and Mg0.4Al2.4O4 ceramics with defect structures

Mg_0.7Al_2.2O₄ and Mg_0.4Al_2.4O₄ ceramics with cation vacancies were synthesized using the molten salt method, and the relationships between the microwave dielectric properties and crystal structures of these materials were investigated. The ²⁷Al NMR spectra of these ceramics indicate that the preferential occupation of tetrahedral sites by Al³⁺ cations was enhanced by the introduction of cation vacancies. The λ values of Mg_0.7Al_2.2O₄ and Mg_0.4Al_2.4O₄ ceramics fired at 1600°C, which correspond to the fraction of Al³⁺ cations in tetrahedral sites, were 0.37 and 0.60, respectively. Crystal structure refinements using the Rietveld method suggest that cation vacancies are preferentially located at octahedral sites in both ceramics. The ε_r and Q·f values of a Mg_0.7Al_2.2O₄ ceramic fired at 1600°C were 7.7 and 201 111 GHz, respectively, while those of a Mg_0.4Al_2.4O₄ ceramic fired at 1600°C were 7.5 and 232 301 GHz, respectively. These data demonstrate that the preferential occupation of tetrahedral sites by Al³⁺ cations following the introduction of cation vacancies enhances the Q·f value.     

Application of Poly(acetic Acid)–Based Graft Copolymer as a Compatibilizer for Poly(L-lactic Acid)/Poly(butylenesuccinate) Blend System

Poly(L-lactic acid) (PLLA) was blended with poly(butylenesuccinate) (PBS) using a single-screw extruder to modify the poor characteristics of these polymers. Furthermore, when both polymers were blended, the graft copolymer that was synthesized by partially saponified poly(vinyl alcohol) (PSPVA) and ?-caprolactone (?-CL) was used as a novel compatibilizer. The structure of the synthesized compatibilizer was determined by ¹H or ¹³C NMR. From this result, the ring-opening polymerization of the ?-CL occurred at the hydroxyl group of PSPVA. The structures of the PLLA/PBS solvent-cast blended films could be observed via an optical microscope. From the optical microscopic observation, the structures of the solvent-cast blended films with the synthesized compatibilizer were more homogeneous than those of the solvent-cast blended films without the compatibilizer. The mechanical properties of the PLLA/PBS extruded blended films were determined by a tensile test. The result showed the tensile strength of the blended films with the synthesized compatibilizer was greater than that of the blended films without the compatibilizer.     

Effect of Particle Deposition on Granular Aerosol Filtration: A Comparative Study of Methods in Evaluating and Interpreting Experimental Data

Three methods which can be applied to extract quantitative information on the effect of deposition on filter performance from effluent concentration and pressure drop data were developed. It was found that all three methods are capable of describing the deposition effect in terms of the amount of deposited particles. Furthermore, the method of extrapolation was found to give the most consistent, if not the most accurate, interpretation of experimental data.