Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Heat transfer to laminar flow with temperature — dependent heat generation

Two problems were solved theoretically on the heat transfer to circular tube flow with internal heat source. The one problem is to maintain the mixed-mean temperature of fluid at the inlet temperature. The other is a conjugated problem with a uniformly specified temperature at the outside surface of the wall, accounting for the wall conduction. From the numerical example for the former, it is shown that the mixed-mean temperature can be controlled within 15% error under the estimated condition. From the numerical results for the latter, it is concluded that the influence of wall conduction is more serious than the case without heat generation.     

Effect of platelet-activating factor on lipoprotein lipase and blood lipids

We investigated the effect of platelet-activating factor (PAF) and of the PAF specific antagonist CV-6209 on plasma lipid metabolism, and particularly on post-heparin plasma lipolytic activity in male Wistar rats. Lipoprotein lipase (LPL) activity was enhanced by intravenous injection of PAF before intravenous injection of heparin when the PAF dose was low (0.2 μg/kg). PAF activated hepatic triacylglycerol lipase (HTGL) activity dose-dependently. Plasma triacylglycerols (TG) significantly decreased with the activation of LPL and/or HTGL. Plasma total cholesterol (TC) and phospholipid (PL) levels decreased at a low dose of PAF (0.2 μg/kg), but increased when higher doses were used. The PAF antagonist CV-6209 partially reversed the PAF induced effects on HTGL, TC and PL. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, Tokyo, Japan, May 1989.     

An improved prediction result of entropic‐FV model for vapor–liquid equilibria of solvent–polymer systems

In this work, entropic expressions of UNIFAC‐FV and Entropic‐FV models were evaluated by using an extensive database of infinite dilution vapor–liquid equilibrium (VLE) data of athermal systems containing polypropylene, polyethylene, and polyisobutylene. For the infinite dilution athermal systems, performance of the Entropic‐FV model was better than that of the UNIFAC‐FV model. Then, finite concentration VLE data of non‐athermal systems that consisted of 16 polymers and 36 solvents containing a large variety of solvent–polymer systems ranging from nonpolar to polar substances were considered to optimized 46 pairs of group interaction parameters of the Entropic‐FV model. For systems containing polar solvents of three types of solvents studied, revised group interaction parameters gave significant improvements from 17.9 to 13.0% average absolute deviation (AAD) of solvent activities. For overall results, improvements were achieved from 15.1 to 12.4% AAD. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1145–1153, 2005     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.     

Electron-beam irradiation-induced grafting of acrylonitrile onto polyethylene

Low- and high-density polyethylene (PE) films were grafted with acrylonitrile (AN) by electron beam prior to irradiation. The distribution of graft chains over the cross section of the sample film was analyzed in terms of the distribution of nitrogen atoms contained in the AN by means of an electron probe microanalyzer (EPMA), and graft sites were studied in relation to the effect of grafting temperature on the percent graft and the oxygen permeability of the sample films. It was found that diffusion of AN into the film was the rate-limiting step in the grafting process, thus restricting the grafting to the surface of the film in the initial grafting stages. However, the grafting shifted to the center of film as the graft process proceeded, until a uniform distribution of graft chains was observed across the entire film thickness. High-density polyethylene (HDPE) was found to display a higher percent graft than did low-density polyethylene (LDPE), and percent graft tended to increase with increasing grafting temperature. On the other hand, film oxygen permeability decreased with increasing percent graft, but this decreasing trend decreased with increasing percent graft. These findings suggest that the grafting is initiated by radicals trapped in the amorphous phase near the crystalline regions and at the surface of crystallites and that graft chains grow toward the amorphous regions. As for the radicals contributing to graft polymerization, it appears that AN permeates deeper near the crystalline surface and that graft chains grow from these sites.     

A superconducting filter to separate an oxygen and argon mixture

Hot isostatic pressing in an oxygen atmosphere, known as O₂-HIP method, has been used successfully to synthesize oxide materials, as well as to produce porous materials. In this paper a porous superconducting oxide is synthesized by this method and its application as a gas filter is described. Porous superconductors can be used to separate a mixture of paramagnetic and diamagnetic gases, such as oxygen and argon. Separation occurs after a magnetic field is applied and is based on the Meissner effect. Experimental results showed that the oxygen content of an oxygen/argon mixture increased after passing through a filter with large pore size (about 10 m).     

Adaptive interpolation scheme for NURBS curves with the integration of machining dynamics

This paper develops a comprehensive interpolation scheme for non-uniform rational B-spline (NURBS) curves, which does not only simultaneously meet the requirements of both constant feedrate and chord accuracy, but also real-time integrates machining dynamics in the interpolation stage. Although the existing work in this regard has realized the importance to simultaneously consider chord error and machining dynamics, none has really incorporated these in one complete interpolation scheme. In this paper, machining dynamics is considered for three aspects: sharp corners or feedrate sensitive corners on the curves, components with high frequencies or frequencies matching machine natural ones and high jerks. A look-ahead module was developed for detecting and adaptively adjusting the feedrate at the sharp corners. By Fast Fourier Transform (FFT) analysis with a moving window in the interpolation stage identified were some special frequency components such as those containing high frequencies or with frequencies matching machine natural ones. Then, the notch filtering or time spacing method was used to eliminate these components. To more completely reduce feedrate and acceleration fluctuations, the jerk-limited algorithm was also developed. Finally, the interpolated feedrate was further smoothened with B-spline fitting method and the NURBS curves were re-interpolated with the smoothened feedrate. During the interpolation, the chord error was repeatedly checked and confined in the prescribed tolerance. Two NURBS curves were used as examples to test the feasibility of the developed interpolation scheme.     

Improvement of Formability by Oscillation of Internal Pressure in Pulsating Hydroforming of Tube

A new history of internal pressure in the hydroforming processes of tubes is developed to attain high formability. The effect of improvement of formability by the oscillation of internal pressure in a pulsating hydroforming process of tubes is examined using both finite element simulation and experiment. The deformation behaviour during the hydroforming is greatly affected by the oscillation of internal pressure. For a monotonic history of small internal pressure, the wrinkling was caused by insufficient bulging, whereas the necking and bursting occurred for a monotonic history of large internal pressure. The occurrence of these defects can be avoided by oscillating the internal pressure in the pulsating hydroforming. The improvement of formability in the pulsating hydroforming is due to both low pressure and oscillation of pressure. The effects of the amplitude and cycle number of pressure in the pulsating hydroforming on the deformation behaviour are investigated. It is found the oscillation of internal pressure is effective in preventing the occurrence of defects.     

Data Center as a Key Player of a District Electric Power and Heat Network System： A Comparison in Urban and Suburb Regions

A DC （data center） demands air-conditioning power as large as the 1/3-1/2 of total electricity consumption. Thus, energy saving of cooling power of DC yields considerable effect on both economic and environmental views. PV （Photovoltaic） and absorption refrigerator with CGS （cogeneration systems） or gas boiler are possible power saving options. The waste warm air from DC would be utilized for greenhouse heating when DC and greenhouse locate near in the suburbs. In this study, the authors develop an energy network model to assess the potential contribution of DC as a major electric power and chilled air consumer as well as the warm air supplier in a district to the energy efficiency improvement. The evaporation heat of LNG （liquefied natural gas） utilization is also considered as well as PV, CGS. This model is applied to the cases of the urban area in Tokyo which involves athletic center, shops and hospital and the suburbs including greenhouse and then compared.