InSb,GaSb, and GaInSb grown using trisdimethylaminoantimony

GalnSb alloys as well as the constituent binaries InSb and GaSb have been grown by organometallic vapor phase epitaxy using the new antimony precursor trisdimethylaminoantimony (TDMASb) combined with conventional group III precursors trimethylindium (TMIn) and trimethylgallium (TMGa). InSb layers were grown at temperatures between 275 and 425°C. The low values of V/III ratio required to obtain good morphologies at the lowest temperatures indicate that the pyrolysis temperature is low for TDMASb. In fact, at the lowest temperatures, the InSb growth efficiency is higher than for other antimony precursors, indicating the TDMASb pyrolysis products assist with TMIn pyrolysis. A similar, but less pronounced trend is observed for GaSb growth at temperatures of less than 500°C. No excess carbon contamination is observed for either the InSb or GaSb layers. Ga_1-xIn_xSb layers with excellent morphologies with values of x between 0 and 0.5 were grown on GaSb substrates without the use of graded layers. The growth temperature was 525°C and the values of V/III ratio, optimized for each value of x, ranged between 1.25 and 1.38. Strong photoluminescence (PL) was observed for values of x of less than 0.3, with values of halfwidth ranging from 13 to 16 meV, somewhat smaller than previous reports for layers grown using conventional precursors without the use of graded layers at the interface. The PL intensity was observed to decrease significantly for higher values of x. The PL peak energies were found to track the band gap energy; thus, the luminescence is due to band edge processes. The layers were all p-type with carrier concentrations of approximately 10¹⁷ cm³. Transmission electron diffraction studies indicate that the Ga_0.5In_0.5 Sb layers are ordered. Two variants of the Cu-Pt structure are observed with nearly the same diffracted intensities. This is the first report of ordering in GalnSb alloys.     

Room temperature characterization of Hg1-xCdxTe P-on-n heterostructure photodiodes

Measurements of 77K R_oA and 300K reverse bias dynamic impedance (R_dA) products at one volt reverse bias has been carried out to assess the degree of correlation of this figure of merit. Planar P-on-n heterostructures were grown on near lattice-matched CdZnTe substrates with Hg_1-xCd_xTe (0.20< x <0.30) by molecular beam epitaxy. These devices were passivated with CdTe and doped with indium and arsenic as n- and p-type dopants, respectively. Current-voltage characteristic of these devices exhibit thermally generated dark currents at small and modest reverse bias. We have observed that R_oA values of these long wavelength infrared P-on-n heterostructure photodiodes at 77K correlate with room temperature R_dA values. Diode arrays with high room temperature R_dA values at one volt reverse bias also have high R_oA values at 77K. Similarly, low R_dA values at room temperature indicate poor performance at 77K where deviation from diffusion current occurs at reverse bias of 0.2 to 1 volt at room temperature. The results presented here, for a small samples of devices, demonstrate that room temperature measurements of current-voltage characteristics to evaluate Hg_1-xCd_xTe (0.22< x <0.28) diode performance and array uniformity at lower temperatures can be used. This provides an acceptable criteria for further study at lower temperatures.     

Simple ASK transmitter using a 790 nm self-pulsating laser diodefor local area networks

A simple amplitude shift keying (ASK) optical link is demonstrated by using a low-cost self-pulsating laser diode and an envelope detector for a low-cost broadband local area network. A link sensitivity of -22 dBm was achieved at 200 Mbit/s. Because the self-pulsation frequency can be tuned by the bias current, frequency division multiplexing can be simply implemented for multiuser applications     

A 0.65-ns, 72-kb ECL-CMOS RAM macro for a 1-Mb SRAM

An ultrahigh-speed 72-kb ECL-CMOS RAM macro for a 1-Mb SRAM with 0.65-ns address-access time, 0.80-ns write-pulse width, and 30.24-μm ² memory cells has been developed using 0.3-μm BiCMOS technology. Two key techniques for achieving ultrahigh speed are an ECL decoder/driver circuit with a BiCMOS inverter and a write-pulse generator with a replica memory cell. These circuit techniques can reduce access time and write-pulse width of the 72-kb RAM macro to 71% and 58% of those of RAM macros with conventional circuits. In order to reduce crosstalk noise for CMOS memory-cell arrays driven at extremely high speeds, a twisted bit-line structure with a normally on MOS equalizer is proposed. These techniques are especially useful for realizing ultrahigh-speed, high-density SRAM's, which have been used as cache and control storages in mainframe computers     

A design technique for a high-gain, 10-GHz class-bandwidth GaAsMESFET amplifier IC module

A design procedure is proposed for a high-gain and wideband IC module, using stability analysis and a unified design methodology for ICs and packages. A multichip structure is developed using stability analysis and the requirements for stable operation are determined for each IC chip, package, and interface condition between them. Furthermore, to reduce the parasitic influences, several improvements in the interface and package design are clarified, such as wideband matching and LC resonance damping. IC design using effective feedback techniques for enlarging the bandwidth are also presented. The ICs are fabricated using 0.2-μm GaAs MESFET IC technology. To verify the validity of these techniques, an equalizer IC module for 10-Gb/s optical communication systems was fabricated, achieving a gain of 36 dB and a bandwidth of 9 GHz     

Simulating process-induced gate oxide damage in circuits

Advanced processing techniques such as plasma etching and ion implantation can damage the gate oxides of MOS devices and thus pose a problem to circuit reliability. In this paper, we present a simulator which predicts oxide failure rates during and after processing and pinpoints strong charging current locations in the layout where changes can be made to improve circuit hot-carrier reliability. We present the models and experimental results used to develop the simulator and demonstrate the usefulness of this simulator     

Photocurrent effect on the zero-Bias dynamic resistance of HgCdTe photodiode

A new physical model is presented for the illumination-dependence of the zero-bias resistance-area product (R₀A) of HgCdTe photodiode. The model is based on three independent mechanisms. They are the depletion region volume change with the applied bias, the diffusion distance change with the moving depletion region edge, and the minority carrier accumulation in the depletion region which affects the minority carrier diffusion. Analytic equations are derived for the photodiode current-voltage characteristics and R₀A products. The results of the model have been compared with experimental data obtained from several Hg_0.7Cd_0.3Te diodes with an identical diode structure having different absorbing amount of light. The model showed good agreement with the experimental data.     

Chaos control and noise suppression in external-cavitysemiconductor lasers

Feedback-induced chaos and intensity noise enhancement in a laser diode with external optical feedback are studied by computer simulations. The enhancement of relative intensity noise (RIN) that is often observed in experiments is considered as a result of the feedback-induced deterministic chaos and the intensity noise suppression is treated from the viewpoint of chaos control. Especially, the conventional noise suppressing technique known as a high-frequency injection modulation is turned into a problem of stabilizing chaos through parameter modulations. We developed an analytical method which allows to optimize the modulation frequency from the linear stability analysis of the dynamical model that describes the laser diode with external feedback. The robustness of the modulation with respect to the modulation frequency and depth is verified and the results suggest the feasibility of applying our method to actual noise suppression. The RIN in the low-frequency region (up to 100 MHz) is shown to be reduced to the solitary laser level when the feedback-induced chaos is effectively controlled with the optimized modulation frequency     

Destination-driven routing for low-cost multicast

We present a destination-driven algorithm that optimizes for applications, such as group video or teleconferencing, that require multicast trees with low total cost. The destination-driven algorithm uses a greedy strategy based on shortest-path trees and minimal spanning trees but biases routes through destinations. The performance of the algorithm is analyzed through extensive simulation and compared with several Steiner tree heuristics and the popular shortest-path tree (SPT) method. The algorithm is found to produce trees with significantly lower overall cost than the SPT while maintaining reasonable per-destination performance. Its performance also compares well with other known Steiner heuristics. Moreover, the algorithm does not suffer from high complexity common to most Steiner tree heuristics and builds a route by querying only incident links for cost information     

Development of the Base Station Controller and Manager in the CDMA Mobile System

The base station (BS) in the CDMA Mobile System (CMS) connects calls through the radio interface and is designed to provide mobile subscribers with high quality service in spite of mobile subscribers’ motions. The BS consists of multiple base station transceiver subsystems (BTSs), a base station controller (BSC) and a base station manager (BSM). This paper is concerned with the BSC and the BSM. The BSC is located between the BTSs and the mobile switching center (MSC) connected with the public network, and is responsible for controlling mobile calls from and to mobile subscribers via the BTSs. The BSM provides operator-interfaces per the BS and takes responsibility of operation and maintenance (OAM) of the BS. Design of the BSC is based on two module types: functional module and unit module. The functional module is used to support new services easily and the unit module to increase the system capacity economically. Both modular types are easily achieved by inserting the corresponding modules to the system. Particularly, in order to efficiently support the soft handover which is one of CDMA superior advantages, the BSC adopts a large high-speed packet switch connecting up to 512 BTSs, and thus mobile subscribers can be provided with soft handover in high probability. The BSM is based on a commercial workstation to support OAM functions efficiently and guarantee high reliability of the functions. The BSM uses graphical user interface (GUI) for efficient OAM functions of the BS.