V–I characteristics of solid polymer electrolytic (SPE) dehumidifier

Measurements of the V–I characteristics of a solid polymer electrolytic (SPE) dehumidifier were done using a modified SPE dehumidifier with four electrodes which included two electrodes to carry the main current and the other two electrodes to measure the voltages applied to the electrical double layer, which are the boundary voltages between the electrodes and the SPE membrane. The measured results were analyzed using the Butler-Volmer equation to examine the validity of the measurements. The current flowing in the dehumidifier is produced by the decomposition of water near the anode. Therefore, under a steady-state condition, the current should be proportional to the supply rate of water to the anode. On the other hand, a two-layer model for the SPE dehumidifier presented in our previous article showed that the current flowing in the dehumidifier was roughly proportional to the water content in the vicinity of the anode. These results were introduced for interpretation of the V–I measurements of the SPE dehumidifier. It was concluded that the dehumidifier current was expressed in the form of a Butler-Volmer equation as a function of the electrode boundary voltages which were the voltages across the boundary between the electrodes and the SPE membrane. An experimental formula for the current under a steady-state condition was developed as a function of the water content near the anode and the boundary voltages.     

Absorption and Fluorescence Spectra of Nitrobenzanthrones

To identify nitrobenzanthrones (NBAs) such as 3-nitro-7 H -benz[ de ]anthracene-7-one (3-NBA) on the basis of their electronic spectral data, we have synthesized 1-, 2-, 3-, 9-, and 10-NBAs and measured their absorption and emission spectra. The first strong absorption band of the NBAs appeared in the region 350-440 nm; the band of 10-NBA was red-shifted by about 20 nm. The molar absorptivities of 3- and 9-NBA were about two times as large as those of the others. The fluorescence spectra of the NBAs varied more largely with the position of the nitro group compared to the absorption spectra. The quantum yields of fluorescence were very small, ranging from ～10 m 2 for 2- and 10-NBA to ～10 m 4 for 1- and 3-NBA. 3-NBA exhibited a characteristic spectrum with two broad bands at 450 and 530 nm. On excitation causing an n ~ * transition in the NBAs, their fluorescence intensities increased by a factor of 10. Phosphorescence was observed at 77 K for all compounds though that of 1-NBA was very weak. These results give the promise of characterizing individual isomers of NBAs on the basis of their spectroscopic data.     

Decomposition and regeneration of methane in the absence and the presence of a hydrogen-absorbing alloy CaNi5

Suitable catalysts for the decomposition of methane into carbon and hydrogen and for the regeneration of methane by hydrogenation of the carbon have been looked for in a series of transition metals and precious metals supported on various carriers. The most active catalyst for both reactions was Ni/SiO₂. The carbon formed on this catalyst was thermodynamically less stable than graphite. The different rate equations for the decomposition of methane obtained for the fresh and carbon deposited Ni/SiO₂ suggest that the rate-determining steps are different for the two catalysts. The highest number of carbon atoms deposited per one Ni atom was 31 at 773 K. However, the number of methane molecules recovered easily at 773 K was limited to 1.5 per Ni atom.

A physical mixture of Ni/SiO₂ and CaNi₅, a hydrogen-absorbing alloy, enhanced the decomposition rate of methane, enabling the complete conversion of methane at 773 K beyond the thermodynamic limitation. The presence of CaNi₅ at 273 K separated from the catalyst in a reaction system further enhanced the decomposition of methane due to an increased hydrogen-absorbing capacity of the CaNi₅ at low temperatures. The carbon deposited on Ni/SiO₂ in this case was reactive to be hydrogenated back to methane at 773 K, giving an average 7.5 CH₄ molecules per one Ni atom.     

Modification of tribological performance of DLC films by means of some elements addition

The elements added diamond-like carbon films (hydrogen, fluorine, and sulfur) fabricated from C₂H₂:H₂, C₂H₂:CF₄ and C₂H₂:SF₆ mixtures were used to compare and study the effects of element contents on the deposition and tribological properties of films prepared by plasma-based ion implantation (PBII). The structure of the films was analyzed by Raman spectroscopy. Hardness and elastic modulus of films were measured by nano-indentation hardness testing. Contact angle and surface energy of films were measured by contact angle measurement. Tribological characteristics of films were performed using a ball-on-disk friction tester. The results indicate that with the increasing element contents, the hardness and elastic modulus, and surface energy of all films decreases, while the surface angle tends to increase. Additionally, H-DLC films at C:H flow rate ratio of 1:4 shows a friction coefficient of 0.08 under ambient air, which are considerable improvement in the tribological properties. This is due to the formation of a transfer films on the interface and high hydrogen contents. For F-DLC films and S-DLC films, does not show a significant decrease in the friction coefficient with the fluorine and sulfur contents under ambient air. The decrease in the friction coefficient is greater under high vacuum than under ambient air.     

Characterization of the Oxide Scale Formed on T12 Water Wall Tube After Long-term Service in Supercritical Power Plant

Oxidation of Metals - Oxide scale control is one of the critical maintenance issues in fossil fuel power plant. Hence, the water treatment of the feed water has been changed from all-volatile...     

Power characteristics of unsteadily forward–reverse rotating impellers in an unbaffled aerated agitated vessel

Power characteristics of an unbaffled aerated agitated vessel with unsteadily forward‐reverse rotating impellers, ie a new type of gas–liquid agitator named ‘AJITER’, treating viscous Newtonian liquids were studied experimentally. Measurements were first made on the agitation torque, ie the torque on the drive shaft on which forward–reverse rotating impellers with four delta‐type blades were attached, and the data obtained were analyzed by fitting them to an equation consisting of two terms with respect to the resistance of the fluid, one due to viscous drag and the other due to added moment of inertia. The effects of operating conditions and physical properties of liquids on the drag and added moment of inertia coefficients were then evaluated, and empirical relationships which estimate values of these coefficients, useful to predict the unsteady behavior and magnitude of agitation torque, were presented. Furthermore, equations were developed for estimating the average and maximum power consumptions as a function of the drag and added moment of inertia coefficients. Prediction of respective power levels in AJITER by these equations was also discussed. © 2001 Society of Chemical Industry     

A SHORT-CUT METHOD FOR DETERMINING CONCENTRATION DEPENDENT DIFFUSIVITY IN LIQUID FOODS AND POLYMER SOLUTIONS FROM REGULAR REGIME DRYING CURVES

A simple method for determining concentration (water or solvent content) dependent diffusivity in liquid foods and polymer solutions from the regular regime drying curve was developed on the basis of the power-law diffusion model. The method was first tested to the drying data generated from numerical solutions of the diffusion equation with various types of concentration dependent diffusivities. The present method was found to be very simple yet accurate compared with the previous methods. Then, the drying rates of various sugar solutions experimentally obtained were analyzed on the basis of the present method to determine the moisture content dependent diffusivities.     

Application of Poly(acetic Acid)–Based Graft Copolymer as a Compatibilizer for Poly(L-lactic Acid)/Poly(butylenesuccinate) Blend System

Poly(L-lactic acid) (PLLA) was blended with poly(butylenesuccinate) (PBS) using a single-screw extruder to modify the poor characteristics of these polymers. Furthermore, when both polymers were blended, the graft copolymer that was synthesized by partially saponified poly(vinyl alcohol) (PSPVA) and ?-caprolactone (?-CL) was used as a novel compatibilizer. The structure of the synthesized compatibilizer was determined by ¹H or ¹³C NMR. From this result, the ring-opening polymerization of the ?-CL occurred at the hydroxyl group of PSPVA. The structures of the PLLA/PBS solvent-cast blended films could be observed via an optical microscope. From the optical microscopic observation, the structures of the solvent-cast blended films with the synthesized compatibilizer were more homogeneous than those of the solvent-cast blended films without the compatibilizer. The mechanical properties of the PLLA/PBS extruded blended films were determined by a tensile test. The result showed the tensile strength of the blended films with the synthesized compatibilizer was greater than that of the blended films without the compatibilizer.