一种微透镜阵列的研制

介绍一种利用表面张力的作用、以光纤作材料、用分离的自聚焦透镜制作微透镜阵型的方法，这种方法具有制作工艺简单、无须昂贵设备等优点，用此方法实际制作了具有良好连续面型的微透镜阵列，并对制作的微透镜阵列进行了测试，效果较好。     

A new method to suppress harmonics using /spl lambda//4 bias line combined by defected ground structure in power amplifiers

A new /spl lambda//4 bias line combined by a dumb-bell shaped defected ground structure (DGS) is proposed to suppress harmonics in power amplifiers. The proposed DGS bias line maintains the required high impedance even after DGS is inserted, while the width and length of the /spl lambda//4 bias line are broader and shorter than those of conventional bias lines. When the DGS bias line is used in power amplifiers, the third harmonic components as well as the second harmonic are reduced, because of the increased slow-wave effect over wide harmonic band. It is shown that the reduction of the third harmonic component, the improvement of 1 dB compression point, and power added efficiency are 26.5 dB, 0.45 dB, and 9.1%, respectively.     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

Theoretical analysis of cladding-mode waveguide dispersion and its effects on the spectra of long-period fiber grating

A new method to control the free spectral range (FSR) of a long-period fiber grating (LPFG) is proposed and theoretically analyzed. As the refractive index decreases radially outward in the silica cladding by graded doping of fluorine, waveguide dispersion in the cladding modes was modified to result in the effective indexes change and subsequently the phase-matching conditions for coupling with the core mode in a LPFG. Enlargement of the FSR in a LPFG was theoretically confirmed.     

Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

洼60-H26水平井套铣打捞技术

洼60-H26井是一口中曲率水平井,设计井深1 922 m,由于地面条件的限制,设计采用三维井眼轨道。该井水平段在钻至井深1 801 m时,发生卡钻事故。在卡钻事故处理过程中,采用测卡、爆炸松扣技术取出上部钻具后,应用了不同规格的套铣管对被卡钻具进行套铣,采用间歇式套铣方式实现了大斜度井段(45°-90°)的安全套铣,采用短套铣管完成了时水平井段内φ215．0 mm稳定器的套铣,采用φ228．6 mm套铣管成功套铣水平井段被卡LWD仪器,最后通过震击器震击成功解卡。详细介绍了洼60-H26水平井卡钻事故的处理过程,分析了在水平段处理卡钻事故的难点。该井处理卡钻事故的经验,对以后水平井施工中处理井下事故、打捞贵重仪器具有借鉴价值。     

布帮鞋无浆贴合工艺技术

本工艺是对原有工艺的改进，突破了原有布帮鞋不能采用无浆贴合的局限性，对原有工艺中的不足有了很大的改进，提高了生产效率，改善了鞋子外观质量，增加了鞋子的美观性。     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

射频板条CO_2激光器并联谐振技术的研究

本文利用周期性网络模型计算了射频板条CO2激光器电极的纵向电压分布．探讨了并联谐振技术在板条器件中获得成功运用的原因．提出了利用并联谐振技术进一步提高电压分布均匀性的两个途径．