甲基丙烯酸乙酯合成工艺研究

以大孔强酸性离子交换树脂为催化剂,甲基丙烯酸(MAA)与乙醇直接酯化合成甲基丙烯酸乙酯(EMA)。在MAA与乙醇摩尔比为1:3、反应温度89～93℃、空速0.3h~(-1)的条件下,MAA转化率不低于98％,EMA的选择性不低于99％。     

桩帽处理对灌注桩高应变检测的影响

本文给出砼灌注桩高应变检测中桩帽的施工工艺 ,并讨论其对测试结果的影响。     

Interface characteristics and mechanical properties of carbon fibre reinforced copper composites

Interface characteristics of carbon fibre reinforced copper matrix composites materials with various interface states and their effect on the flexural strength of composites have been studied. Interfacial states are mechanical bonding, dissolution bonding and reaction bonding. To a certain extent, raising the interfacial strength enables an increase in the flexural strength due to prevention of carbon fibre being pulled out under low stress during fracture process of composites. Raising the interfacial bondage strength, causes the brittleness of composites to increase; the fracture surface of composites is converted from a fibre pull-out model to a fibre even model. While strengthening the interface bondage, the extent of chemical reaction and dissolution at the interface must be controlled to avoid degrading the carbon fibre.     

POCV-200/31.5型液控单向阀

介绍了一种用于液压支架大流量、快速移架系统中的POCV——200／31．5型液控单向阀的工作原理和结构特点。分析了该阀的性能，并指出了其推广应用前景。     

炉衬产生的氧对真空钢液脱氮的动力学影响

采用 99.99%氧化镁砂捣打炉衬的 2 0kg真空感应炉 ,研究了超低碳钢熔炼时炉衬产生的氧对真空钢液脱氮的影响。试验结果表明 :钢液中氧含量在 1 2 0× 1 0 - 6 时 ,脱氮的限制性环节是界面化学反应 ;随炉衬中氧的逸出 ,当钢液中氧含量在 5 1 0×1 0 - 6 时 ,真空钢液脱氮处于界面化学反应和液相边界层扩散控制的边缘区域 ,脱氮速率降低     

乙烯装置中汽油分馏塔设计浅析

对汽油分馏塔的技术特点进行了分析,对急冷油系统的设计和汽油分馏塔的内件选择和设计进行了分析和讨论.     

Slow eroding biodegradable multiblock poloxamer copolymers

Biodegradable multiblock poloxamers (BMPs) with gel duration of 8 h to several weeks were prepared by varying their molecular weights from 4000 to 40 000 g mol^?1. The molecular weight of the BMP was controlled by changing the poloxamer to coupling agent ratio. Assuming a micelle packing model of the BMP gel, as in the case of a poloxamer gel, the micelle properties and critical gel concentration of BMPs were investigated on the basis of the scaling concept. The findings suggest that the control of molecular weight by hydrolyzable groups can be a facile approach to optimize the gel properties for biomedical applications. Copyright © 2005 Society of Chemical Industry     

生物除铬(VI)效果及机理探讨

以特定污泥挂膜的自制厌氧生物滤床系统具有良好的去铬(VI)能力。恒流泵最佳流量为47mL/min,外加碳源使废水COD约140mg/L,铬(VI)的浓度由60mg/L左右降到0.5mg/L以下(一级排放标准),需要4h,而对照组(未加碳源)需要14h。铬(VI)浓度由64.66mg/L提高到75.53mg/L时,对系统负面影响甚微,提高到95.47mg/L时,系统出水达标所需时间延长到7.5h。添加微量金属离子与未添加微量金属离子的情况相比,处理效率提高21.26%。分析试验表明:铬(VI)的去除途径可能是由生物还原作用将六价铬还原为三价铬,形成氢氧化铬沉积于微生物表面。     

Synthesis and characterization of an interpenetrating polymer network composed of poly(methacrylic acid) and poly(vinyl alcohol)

Temperature and pH‐responsive interpenetrating polymer network (IPN) hydrogels, constructed with poly(methacrylic acid) (PMAA) and poly(vinyl alcohol) (PVA), by a sequential IPN method, were studied. The characterization of IPN hydrogels was investigated by Fourier‐transform infrared spectroscopy, differential scanning calorimetry (DSC) and swelling under various conditions. The IPN hydrogels exhibited relatively high swelling ratios, in the range 230–380 %, at 25 °C. The swelling ratios of the PMAA/PVA IPN hydrogels were pH and temperature dependent. DSC was used for the quantitative determination of the amounts of freezing and non‐freezing water. The amount of free water increased with increasing PMAA content in the IPN hydrogels. Copyright © 2004 Society of Chemical Industry