Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

Changes in the gaseous H2S barrier properties of damaged silicate coated nylon 6 films

The damage imposed on SiO _x deposited nylon 6 films as a result of abrasion with a cotton cloth and Gelboflex testing was examined by evaluating the rate at which copper plates, which were enveloped by the damaged films, were corroded by H₂S. Abrasion with a cotton cloth caused some micro-cracking of the SiO _x layer and the permeation rate of H₂S approached that of the uncoated nylon 6 film. Damage to the SiO _x layer by twisting and crushing progressed gradually with the number of Gelboflex test cycles and correspondingly the corrosion rate of the copper plates increased. Comparison of the corrosion rates of the copper plates kept in the pouches made of various commercial films with those obtained for the damaged SiO _x deposited nylon 6 films showed a clear relationship between the H₂ permeation rate of the films and the corrosion rate of the copper plates by H₂S.     

Heat Transfer by Radiation through a Vapor Gap under Conditions of Film Boiling of Liquid

Theoretical models of heat transfer by radiation through a vapor gap under conditions of film boiling of liquid are treated, namely, a general wave model for a gap of arbitrary thickness and an approximate model of geometrical optics. Calculations are performed of heat transfer by radiation under conditions of film boiling of water on hot surfaces of refractory metal and molten oxide. Practical recommendations are given to calculate the distribution of the power of absorbed radiation in a water layer.     

Design principles underlying circadian clocks.

A fundamental problem for regulatory networks is to understand the relation between form and function: to uncover the underlying design principles of the network. Circadian clocks present a particularly interesting instance, as recent work has shown that they have complex structures involving multiple interconnected feedback loops with both positive and negative feedback. While several authors have speculated on the reasons for this, a convincing explanation is still lacking.We analyse both the flexibility of clock networks and the relationships between various desirable properties such as robust entrainment, temperature compensation, and stability to environmental variations and parameter fluctuations. We use this to argue that the complexity provides the flexibility necessary to simultaneously attain multiple key properties of circadian clocks. As part of our analysis we show how to quantify the key evolutionary aims using infinitesimal response curves, a tool that we believe will be of general utility in the analysis of regulatory networks. Our results suggest that regulatory and signalling networks might be much less flexible and of lower dimension than their apparent complexity would suggest.     

RF microelectronics for W-CDMA mobile communication systems

Third generation (3G) mobile communication systems are now just starting to be introduced. With a maximum data rate of 2 Mbit/s they will make wireless access to broadband data services like the Internet or video applications feasible. Most of the different physical layer technologies summarised under the acronym 3G are based on wideband-CDMA (W-CDMA), in contrast to existing second generation systems, which mostly use TDMA and FDMA. This has severe consequences for the design of the transceiver front-ends. During standardisation these were assumed to have an adequate RF performance yet they still present a performance bottleneck for the system. Starting with a short introduction to UMTS (Universal Mobile Telecommunications System)-the 3G standard to be deployed in Europe and already operating in Japan-this paper describes by way of example some of the test cases specified for UMTS and their impact on the analogue front-end. It is shown that accurate simulation of all the analogue and digital signal processing is necessary in order to predict the RF performance needed of today's commercial RFICs. The paper then presents and reviews some actual design examples. Finally, possible technologies and techniques for application in future mobile terminals are discussed     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

The measurement of solar array discharges in a simulated spaceenvironment

A spacecraft in a plasma builds up charge on all the dielectric surfaces and interfaces. Once the net charge exceeds the dielectric breakdown of the material, a discharge occurs. One of the more susceptible pieces of equipment is the antenna/receiver system. The radiated E-field may be strong enough to create an ambiguous signal which may be misinterpreted by the system electronics and cause a system malfunction. A technique is developed to monitor the radiated E-field of materials discharging in an electron environment, using vacuum chambers for measuring the material discharges which are made of highly reflective materials. These chambers affect the radiated E-field due to multiple reflections from the walls. The technique developed defines a method for correcting the effects caused by the measurement facilities. The methodology is: monitor the radiated E-field with a broadband dipole antenna, and digitize the radiated signal as a function of time. Determine the frequency response of the radiated E-field using an FFT algorithm. Measure the transmission and reflection characteristics of the two-port network inside the measurement chamber, and determine the impedance network from the measured E-parameters across the frequency band of interest. Transform the measured E-field frequency response through the impedance network to obtain the frequency response of the actual radiated discharge current. Find the inverse FFT of this response to obtain the actual radiated discharge current response. This technique aids in the prediction of the E-field coupling into receive antennas on-board actual satellites     

Scattering from and penetration into a dielectric-filled conductingcylinder with multiple apertures

The theory of characteristic modes for aperture problems is used in this paper to solve the equivalent magnetic current and aperture fields due to a conducting cylinder with multiple slots. It is assumed that these slots are illuminated by either a transverse electric (TE) or a transverse magnetic (TM) plane wave and the media inside and outside the cylinder exhibit different electromagnetic properties. The formulation is given for the general case and numerical results for a limited number of slots are presented