Decomposition of CO2 and CO into carbon with active wüstite prepared from Zn(II)-bearing ferrite

CO₂ decomposition reaction into carbon was studied at 300 °C using the H₂-reduced Zn(II)-bearing ferrite which consisted of the Zn(II) oxide and the active wüstite. The H₂-reduced Zn(II)-bearing ferrite was prepared from Zn(II)-bearing ferrite by the reduction with H₂ gas at 300 °C. The wüstite (FeO) in the H₂-reduced Zn(II)-bearing ferrite had a higher value (=0.97, active wüstite) than those of the normal wüstites (0.90<<0.95) prepared at high temperatures (>570 °C). The decomposition reaction of CO₂ proceeds in two steps: (1) CO₂ reduction to CO, and (2) CO decomposition into carbon. In the initial stage, the reduction of CO₂ into CO takes place, accompanying both the oxidation of the active wüstite to the slightly oxidized wüstite, and the transformation of active wüstite and Zn(II) oxide into the Zn(II)-bearing ferrite. After the reaction of the initial stage attains equilibrium of an apparent state of rest, the adsorbed CO is decomposed into carbon, associated with the transformation of the slightly oxidized wüstite and the Zn(II) oxide into the Zn(II)-bearing ferrite.     

Effects of heated seats in vehicles on thermal comfort during the initial warm-up period

Eight subjects participated in a subjective experiment of eight conditions to investigate the effects of heated seats in vehicles on skin temperature, thermal sensation and thermal comfort during the initial warm-up period. The experimental conditions were designed as a combination of air temperature in the test room (5, 10, 15, or 20 °C) and heated seat (on/off). The heated seat was effective for improving thermal comfort during the initial warm-up period when air temperature was lower than 15 °C. Use of heated seats prevented decreases in or increased toe skin temperature. Heated seats also increased foot thermal sensation at 15 and 20 °C. Optimal thermal sensation in contact with the seat was higher when air temperature was lower. Optimal skin temperature in contact with the seat back was higher than that with the seat cushion. Moreover, these optimal skin temperatures were higher when air temperature was lower.     

A study of reactor neutrino monitoring at the experimental fast reactor JOYO

We carried out a study of neutrino detection at the experimental fast reactor JOYO using a 0.76 tons gadolinium loaded liquid scintillator detector. The detector was set up on the ground level at 24.3 m from the JOYO reactor core of 140 MW thermal power. The measured neutrino event rate from reactor on-off comparison was 1.11±1.24(stat.)±0.46(syst.) events/day. Although the statistical significance of the measurement was not enough, backgrounds in such a compact detector at the ground level were studied in detail and MC simulations were found to describe the data well. A study for improvement of the detector for future such experiments is also shown.     

Emerging Immunotherapy for Acute Myeloid Leukemia

Several immune checkpoint molecules and immune targets in leukemic cells have been investigated. Recent studies have suggested the potential clinical benefits of immuno-oncology (IO) therapy against acute myeloid leukemia (AML), especially targeting CD33, CD123, and CLL-1, as well as immune checkpoint inhibitors (e.g., anti-PD (programmed cell death)-1 and anti-CTLA4 (cytotoxic T-lymphocyte-associated protein 4) antibodies) with or without conventional chemotherapy. Early-phase clinical trials of chimeric antigen receptor (CAR)-T or natural killer (NK) cells for relapsed/refractory AML showed complete remission (CR) or marked reduction of marrow blasts in a few enrolled patients. Bi-/tri-specific antibodies (e.g., bispecific T-cell engager (BiTE) and dual-affinity retargeting (DART)) exhibited 11–67% CR rates with 13–78% risk of cytokine-releasing syndrome (CRS). Conventional chemotherapy in combination with anti-PD-1/anti-CTLA4 antibody for relapsed/refractory AML showed 10–36% CR rates with 7–24 month-long median survival. The current advantages of IO therapy in the field of AML are summarized herein. However, although cancer vaccination should be included in the concept of IO therapy, it is not mentioned in this review because of the paucity of relevant evidence.     

Effect of Vertical Misfit on Screw Joint Stability of Implant-Supported Crowns

The passive fit between prosthesis and implant is a relevant factor for screw joint stability and treatment success. The aim of this study was to evaluate the influence of vertical misfit in abutment-implant interface on preload maintenance of retention screw of implant-supported crowns. The crowns were fabricated with different abutments and veneering materials and divided into 5 groups (n = 12): Gold UCLA abutments cast in gold alloy veneered with ceramic (Group I) and resin (Group II), UCLA abutments cast in titanium veneered with ceramic (Group III) and resin (Group IV), and zirconia abutments with ceramic veneering (Group V). The crowns were attached to implants by gold retention screws with 35-N cm insertion torque. Specimens were submitted to mechanical cycling up to 10⁶ cycles. Measurements of detorque and vertical misfit in abutment-implant interface were performed before and after mechanical cycling. ANOVA revealed statistically significant difference (P < 0.05) among groups for vertical misfit measured before and after mechanical cycling. The abutments cast in titanium exhibited the highest misfit values. Pearson correlation test did not demonstrate significant correlation (P > 0.05) between vertical misfit and detorque value. It was concluded that vertical misfit did not influence torque maintenance and the abutments cast in titanium exhibited the highest misfit values.     

Excess Solute Carbon and Retained Tetragonality in Tempered Fe-0.6C-1Mn Martensite and the Effect of Silicon Addition

The tetragonality and carbon distribution in tempered Fe-0.6C-1Mn martensite were investigated by X-ray diffraction and atom probe tomography to elucidate strain relaxation in the tetragonal lattice during tempering and its relationship with the solubility of excess carbon in martensite. Even though tetragonality (c/a) decreased with an increase in the tempering temperature, it persisted at low levels up to 400 °C. Si addition suppressed the decrease in tetragonality at 400 °C by inhibiting recovery in the dislocated matrix. Such persistence implies that dislocation migration is crucial for the complete release of tetragonal lattice strain at such a temperature, in addition to the decrease in the amount of solute carbon in martensite. A low level of tetragonality was observed for martensite containing carbon in the solid solution below the critical value of ~ 0.2 mass pct, at which a bcc structure was predicted. The amount of solute carbon after tempering was linearly correlated with tetragonality in the solute carbon content range of 0.07 to 0.6 mass pct, and the correlation coefficient was similar to those for as-quenched auto-tempered martensite and bainitic ferrite; these results indicate that the amount of excess carbon is simply determined by the amount of tetragonal lattice distortions remaining after carbide precipitation and recovery.

     

A PSS‐Free PEDOT Conductive Film Supported by a Hierarchical Nanoporous Layer Glass

The importance of transparent conductive film is increasing due to its use in applications such as touch‐panel devices. Although indium tin oxide is widely used because of its high conductivity and transparency, conductive polymers are being studied as alternative materials that avoid the use of rare metals and the brittleness associated with existing systems. Polyethylene dioxythiophene (PEDOT)/polyethylene sulfonic acid (PSS) is drawing a lot of attention due to its well‐balanced conductivity, transparency, film formability, and chemical stability. The nonconductive PSS reportedly covers the conductive PEDOT. The PSS shell provides carrier and film‐formability to PEDOT but is also a barrier that hinders electrical conductivity. Therefore, the PEDOT film formability is explored supported by a substrate without the addition of PSS. The “hierarchical nanoporous layer glass” holds the PSS‐free PEDOT with its nanopores to form a homogeneous, transparent film. The PSS‐free PEDOT film thus achieves transparency of over 85% and resistivity of below 500 Ω sq^?1.     

The effect of chemical reaction on the mixing flow between aqueous solutions of acetic acid and ammonia

The basic characteristics of the reacting mixing flow of two streams were investigated. The reaction between aqueous solutions of ammonia and acetic acid, which produces ammonium acetate, was investigated in terms of the effect on the fluid–fluid interface of the mixing flow relative to fluids that did not react. The reaction between these solutions was negligibly exothermic, and there were minimal differences in density. The velocity field in the reacting mixing flow was quantitatively measured using high-speed time-resolved particle image velocimetry (PIV) and the behavior of the mixing flow was qualitatively investigated using laser-induced fluorescence (LIF). The jet width, the velocity field, the kinetic energy and the turbulent intensities are qualitatively estimated and discussed. It was found that the chemical reaction resulted in the suppression of the mixing flow.     

Mixing speed-controlled gold nanoparticle synthesis with pulsed mixing microfluidic system

Gold nanoparticles with diameters of a few tens of nanometer and a narrow size distribution were synthesized using a pulsed mixing method with a microfluidic system which consists of a Y-shaped mixing microchannel and two piezoelectric valveless micropumps. This mixing method enables control of the mixing speed of gold salts and reducing agent by changing the switching frequency of the micropumps, which was our focus to improve the particle size distribution, which is an essential parameter in gold nanoparticle synthesis. In the proposed method, the mixing time was inversely proportional to the switching frequency and the minimum mixing time was 95 ms at a switching frequency of 200 Hz. During synthesis experiments, the mean diameter of the synthesized gold nanoparticles was found to increase, and the coefficient of variation of particle size was found to decrease with decreasing mixing time. We successfully improved the coefficient of variation to less than 10% for a mean diameter of around 40 nm.