Development of a 400 kJ Nb3Sn superconducting magnet for an SMES system

An Nb₃Sn superconducting magnet to store 400 kJ was developed as a unit magnet for a 2.4-MJ SMES system used for stabilization studies of electrical power systems. The superconducting magnet consists of a cryostat and an Nb₃Sn coil. The dimensions of the coil are: 340 mm inner diameter, 700 mm outer diameter and 177 mm axial length. The pool-cooled coil is a stack of 20 Nb₃Sn double pancakes, and the cooling channels are aligned between pancake coils. To reduce Joule loss in electrical power converters, the maximum operating current of the coil is designed to be 350 A, which is one order of magnitude less than the operating currents of similar scale coils for pulse use. The conductor is an Nb₃Sn monolithic conductor with cross section 1.50 × 2.38 mm. For good superconducting stability and high dielectric strength of the coil, the Nb₃Sn double pancakes were wound by the react-and-wind technique. Operation of dc current to 105% (367.5 A) of the design operating current was achieved without quench. After the whole of the coil was exposed out of liquid helium, the coil did not quench under 120 A current operation for more than 2 hours. It was verified that the coil was stable for the SMES system. © 1998 Scripta Technica, Inc. Electr Eng Jpn, 121(3): 44–52, 1997     

Influence of electrode material on pressure‐rise due to arc in a closed chamber

This paper describes the phenomenon of internal pressure‐rise due to arcs ignited between metal rod electrodes in air. First, the internal pressure‐rises in a closed chamber due to arcs were measured at currents within the range of 1 to 12.5 kA. The rod electrodes were made of copper, iron, and aluminum, and were 20 mm in diameter. The measurements showed that the maximum pressure‐rise distinctly differed with each electrode material at the same total arc energy, namely, the maximum pressure‐rise was the highest in the case of the aluminum electrode and was the lowest in the case of the iron electrode. Next, to quantitatively verify this difference, the internal pressure‐rise was estimated, taking into account the energy balance in the closed chamber on each electrode material. It was found that the estimated pressure‐rise approximately agreed with the above experimental results by taking into consideration oxidation reactions of the electrodes, melting and vaporization of the electrodes, and radiation loss of the arcs under certain realistic assumptions. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 174(4): 9–18, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21071     

Current Control Method of Achieving Wide‐Range Power Driving for Linear Synchronous Motor with Half‐Wave‐Rectified Self‐Excitation

In a previous paper, we proposed a novel linear synchronous motor with half‐wave‐rectified self‐excitation. A long‐stator‐type linear synchronous motor was built and its performance was verified by experiments. This paper presents a new current control method for the linear synchronous motor in order to achieve a wide range of speeds and high‐power operations. First, we propose a current control method for high‐thrust operation in the constant‐thrust region. This operation is realized by using the reluctance thrust resulting from the saliency of the linear synchronous motor. We also propose a control method that maximizes the ratio of the thrust to the voltage; this method can be used to expand the operating range. Wide‐range‐speed operation can be achieved by applying this new control method along with field‐weakening control. The thrust and operating characteristics of the proposed control methods are estimated by performing experiments and coupled electric and magnetic analysis.     

Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Calculation of the Characteristics of Salient‐Pole Synchronous Machines Assisted by Permanent Magnets on the Basis of the Operating Principle

In this study we investigate a method for accurately calculating the characteristics of salient‐pole synchronous machines assisted by permanent magnets. First, the operating principle of the machines is investigated by using both finite element analysis and a simple magnetic circuit. Then, a theoretical representation of the assist effect on the permanent magnets is derived based on the magnetic circuit. Finally, the measured and calculated results are compared in order to confirm the validity of the proposed calculation method. We show that the load characteristics of the proposed machine can be accurately estimated from the no‐load and short‐circuit characteristics of the conventional machine without permanent magnets, and the size and magnetization of the inserted permanent magnets.     

Pressure Rise and Propagation Phenomena Due to Fault Arc in Container with Opened Pipe

This paper describes experimental and analytic studies on pressure rise and propagation phenomena due to high current arcs in a container with opened pipes. The shape of the experimental container was chosen taking into account underground common ducts. First, arcs were ignited in the container with varying diameter D and length L of the opened pipes and at arc currents of 4 kA to 12.5 kA and an arc duration of 0.1 s. Based on measured waveforms, the maximum pressure rise and the pressure oscillation frequency were obtained. It was found that there is a tendency for to increase with decreasing D and increasing L, and that D has a much greater impact on . In addition, the tendencies of with changing D and L can be approximately explained by Helmholtz resonance. Second, a CFD model for the container with opened pipe was developed based on the experimental results, and simulations were performed. The simulation results were found to correspond to the experimental pressure rise.     

A New Fluorogenic Probe for the Detection of endo‐β‐N‐Acetylglucosaminidase

We developed a fluorescence‐quenching‐based assay system to determine the hydrolysis activity of endo‐β‐N‐acetylglucosaminidases (ENGases). The pentasaccharide derivative 1 was labeled with an N‐methylanthraniloyl group as a reporter dye at the non‐reducing end and with a 2,4‐dinitrophenyl group as a quencher molecule at the reducing end. This derivative is hydrolyzed by ENGase, resulting in an increase in fluorescence intensity. Thus, the fluorescence signal is directly proportional to the amount of the tetrasaccharide derivative, hence allowing ENGase activity to be evaluated easily and quantitatively. Using this system, we succeeded in measuring the hydrolysis activities of ENGases and thus the inhibitory activities of known inhibitors. We confirmed that this assay system is suitable for high‐throughput screening for potential inhibitors of human ENGase that might serve as therapeutic agents for the treatment of N‐glycanase 1 (NGLY1) deficiency.     

Characteristics of permeation and separation of dimethyl acrylamide-methyl methacrylate random and graft copolymer membranes for a benzene/cyclohexane mixture

When a benzene/cyclohexane mixture was permeated through poly(dimethyl acrylamide-random-methyl methacrylate) (DMAA-r-MMA) and poly(dimethyl acrylamide)-graft-poly(methyl methacrylate) (DMAA-g-MMA) membranes by pervaporation, the benzene-permselectivity of the DMAA-r-MMA membrane changed from the diffusivity selectivity to the solubility selectivity with increasing DMAA content but DMAA-g-MMA membranes with a high DMAA content had the higher apparent diffusivity selectivity than the apparent solubility selectivity. Furthermore, the apparent solubility selectivity for a benzene/cyclohexane mixture between the DMAA-r-MMA membrane and the DMAA-g-MMA membrane with a high DMAA content was remarkably different. These results were attributed to the difference of structure between the copolymers. Received: 27 August 1997/Revised version: 22 October 1997/Accepted: 30 October 1997     

pH-controlled uphill transport of ammonium ions through polymer membranes with sulfonic acid groups

Uphill transport of ammonium ions through a membrane with sulfonic acid groups were investigated with pH-controllers which keep the solution at a constant pH. A membrane with sulfonic acid groups was prepared by casting an aqueous solution containing poly(styrenesulfonic acid) and poly(vinyl alcohol) on a glass plate. When a membrane with one side alkaline and the other acidic was fixed as a diaphragm in a cell, ammonium ions were transported from the alkaline side to the acidic side through the membrane against the concentration gradient of the adjacent solutions. Uphill transport of ammonium ions with pH-controllers was more efficient than without, thus keeping the pH difference between both sides of the membrane constant, which is a driving force for the uphill transport. Furthermore, the effect of pH of the acidic side on the uphill transport was investigated and the mechanism of the pH-controlled uphill transport is discussed.     

Effect of additives on the renaturation of reduced lysozyme in the presence of 4 M urea

Reduced lysozyme was renatured by sulfhydryl-disuffide interchangereactions at pH 8.0 in the presence of 4 M urea, with or withoutadditives at 40°C. In the absence of additives, the finalfolding yield of reduced lysozyme was 40%. In the presence ofsarcosine, glycerol, ammonium sulfate, N-acetyl glucosamineand glucose, its folding yields increased in all cases. In particular,yields increased up to 90% in the presence of 4 M sarcosine.On the other hand, the melting temperatures of lysozyme withor without additives in 0.02 M citrate buffer (pH 6.0) wereevaluated using differential scanning calorimetry. In the absenceof additive, the melting temperature of lysozyme was 73.8°C.In the presence of additives, all melting temperatures werehigher than that of lysozyme in the absence of additives. Moreover,there was a good correlation on addition of additives betweenan increase in the folding yield of reduced lysozyme with 4M urea and an increase in the melting temperature without 4M urea. Therefore, we conclude that additives, which stabilizenative lysozyme, are effective at increasing the folding yieldof reduced lysozyme in 4 M urea.