(p,q)-Logical completeness for output-coherent sets of (p,q)-Logical functions and an application of the set to image processing

We have previously proposed an idea of p-valued input, q-valued output threshold logic to synthesize many-valued, p-valued, logical networks, and derived the condition for (p, q)-logical completeness for the output-closed set of (p, q)-logical functions. In this paper, the condition for (p, q)-logical completeness for the output-coherent set F of (p, q)-logical functions is described, and the proof is given in almost the same way as for the output-closed set. The output-coherent set F is applied to image processing. That is, a restoration scheme is described for images to which normal random noise is added.     

Densification of rare-earth (Lu, Gd, Nd)-doped alumina nanopowders obtained by a sol-gel route under seeding

Rare-earth (RE: Lu, Gd, Nd, 0.10 mol%)-doped alumina nanopowders were prepared by a new sol-gel route using polyhydroxoaluminum (PHA) and RECl₃ solutions under α-alumina (∼ 75 nm) seeding. Among the rare-earth dopants studied, Lu yields the most suitable nanopowders for low-temperature densification. The 0.10 mol% Lu-doped nanopowders, which were obtained at a calcination temperature of 900 °C under 5 mass% α-alumina seeding, consisted of ∼ 80-nm α-alumina particles and γ-alumina nanoparticles. Using these Lu-doped alumina nanopowders, fully densified alumina ceramics with a uniform microstructure composed of fine grains with an average size of 0.61 μm could be obtained at 1400 °C by pressureless sintering. Clearly, the Lu-doped nanopowders obtained here represent a viable option for fabricating dense, finer-grained alumina ceramics because an undoped sample with 5 mass% seeds gave a microstructure with an average grain size of 1.78 μm at 1400 °C.     

Dynamic Characteristics Analysis of Two‐DOF Oscillatory Actuator and Experimental Verification of Prototype

Recently, linear oscillatory actuators have been used in a wide range of applications. In particular, small linear oscillatory actuators are expected to be used in haptic devices by being extended to provide multi‐degree‐of‐freedom motion with arbitrary acceleration. In this paper, we propose a compact two‐DOF oscillatory actuator that can move in various directions on a plane. The static and dynamic characteristics of the actuator are determined by the 3D finite element method. The effectiveness of this method is shown through a comparison of the measured results with the experimental results from a prototype. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(1): 58–65, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22312     

Fabrication of submicron alumina ceramics by pulse electric current sintering using M2+ (M = Mg,Ca, Ni)-doped alumina nanopowders

Dense submicron-grained alumina ceramics were fabricated by pulse electric current sintering (PECS) using M²⁺(M: Mg, Ca, Ni)-doped alumina nanopowders at 1250 °C under a uniaxial pressure of 80 MPa. The M²⁺-doped alumina nanopowders (0–0.10 mass%) were prepared through a new sol–gel route using high-purity polyhydroxoaluminum (PHA) and MCl₂ solutions as starting materials. The composite gels obtained were calcined at 900 °C and ground by planetary ball milling. The powders were re-calcined at 900 °C to increase the content of α-alumina particles, which act as seeding for low-temperature densification. Densification and microstructural development depend on the M²⁺ dopant species. Dense alumina ceramics (relative density ≥99.0%) thus obtained had a uniform microstructure composed of fine grains, where the average grain size developed for non-doped, Ni-doped, Mg-doped and Ca-doped samples was 0.67, 0.67, 0.47 and 0.30 μm, respectively, showing that Ca-doping is the most promising method for tailoring of nanocrystalline alumina ceramics.     

Asymmetric electric double layer capacitors using carbon electrodes with different pore size distributions

Asymmetric capacitors composed of carbon electrodes with different pore size distributions (PSD) were constructed in order to study the fundamental relationship between the PSD of positive and negative carbon electrodes and the performance of electric double layer capacitors. The performance of asymmetric capacitors in a non-aqueous electrolyte solution (TEMA·BF₄/PC) was found to be governed by the PSD of the carbon used in the negative electrode. Capacitance depends on the BET surface area of the negative electrode and the rate performance depends on its mesoporous surface area. These results were explained by the fact that it is more difficult to adsorb large solvated cations (TEMA⁺) in micropores (less than 2 nm wide) than in mesopores (2-50 nm wide), and that this is more difficult with a higher rate of charge-discharge.     

Preparation of novel porous solids from alumina-pillared fluorine micas by acid-treatment

New porous solids from alumina-pillared fluorine micas (APMs), which were obtained from synthetic Na-tetrasilicic fluorine mica [NaMg_2.5Si₄O₁₀F₂], were prepared by sulfuric acid-treatment under mild conditions at 25 °C. The products were investigated by XRD, ICP, SEM, TEM and N₂ adsorption–desorption isotherm at 77 K. XRD measurements indicated that the interlayer pillared structure having a large basal spacing collapsed during the early stages of the acid-treatment. ICP analyses indicated that Al³⁺ and Mg²⁺ ions were leached out from the pillared micas during the acid-treatment. The pore properties of the leached products were found to differ from those of the mother pillared micas: the acid leaching of the pillared micas leads to the formation of mesopores around 3.2 nm in diameter. The correlation between the change in pore properties and cation elution behavior suggests that the mesopore formation results from the leaching of Mg²⁺ ions from the octahedral sheet of the pillared micas. The leached products thus obtained retained the flaky morphology of the mother pillared micas. These results show that the mild acid-treatment using APMs provides a novel route for obtaining unique mesopore solids having the large particle sizes of the mother micas.     

High-pressure viscosity prediction of di(2-ethylhexyl) phthalate and tricresyl phosphate binary mixtures using dielectric relaxation data

Dielectric permittivity and loss in di(2-ethylhexyl) phthalate and tricresyl phosphate binary mixtures were measured over a frequency range from 100 Hz to 1.5 MHz under high pressure. The mixtures showed single dielectric relaxation. The composite plots of the dielectric loss data showed one master curve and time–temperature–pressure superposition were applicable. The prediction of high-pressure viscosity was carried out from the change of dielectric relaxation time with temperature and pressure. The predicted results showed relatively good agreement with viscosity data obtained from a falling-sphere viscometer.     

Observation of the solid-state formation of a TTF–CA complex by terahertz spectroscopy

The solid-state synthesis of a tetrathiafulvalene–chloranil (TTF–CA) complex was demonstrated, and progress in the formation of the complex was monitored using a GaP Raman terahertz (THz) spectrometer. Clear transitions in the THz absorption spectra indicated that the mixture of TTF and CA became the black phase TTF–CA complex. The results of X-ray diffraction, Raman scattering, and FTIR spectra are presented as supporting evidence.     

Geometric control and tuneable pore size distribution of buckypaper and buckydiscs

The fabrication of buckypaper from unfunctionalised multi-walled carbon nanotubes (MWCNTs) without the aid of surfactants or surface modification techniques is accomplished through a novel and quick frit compression method. The dimensions can be controlled through the size of the syringe housing and the through the mass of carbon nanotubes added. Their thicknesses are typically much larger than surfactant-cast buckypaper and range from 120 μm up to 650 μm; buckypaper with thicknesses larger than 500 μm we call buckydiscs. Buckypaper and buckydiscs are mechanically robust to handle, flexible, stable in solvents and possess larger porosities than Triton-X100 cast buckypaper. They also exhibit a memory effect when bending wetted samples, returning to their former geometry on drying. Buckypaper and buckydiscs were studied by mercury intrusion porosimetry to reveal a defined distribution of mesopores and small macropores that is, along with their density and apparent free volume, dependant on the casting solvent and therefore tuneable. Moreover, the frit compression system also allows control over the 3-dimensional geometry of the buckydiscs during the casting process.     

Study on dominant mechanism of high-cycle fatigue life in 6061-T6 aluminum alloy through microanalyses of microstructurally small cracks

The mechanism controlling the fatigue life of a precipitation-hardened Al–Mg–Si alloy (6061-T6) at a high-cycle fatigue (HCF) regime of over 10⁷ cycles was investigated in detail. It was found that over 90% of the total fatigue life was occupied by the growth process of a microstructurally small crack at relatively low stress amplitude. The small crack was often found to be arrested and halted for a long period (more than 10⁶ cycles) before it began to grow again, which resulted in a significantly slow growth process. The small crack was then analyzed not only by the conventional fractography but also by the cross-sectional observation of the crack tip region using a focused ion beam and transmission electron microscopy. These observations, supplemented also by a grain orientation analysis using electron backscattered diffraction, explicitly revealed the following points: (i) the small crack growth observed on the specimen surface is primarily related to facet-type cracking that occurs exclusively at the specimen surface; (ii) the growth direction of the small crack has strong anisotropy (i.e. surface-induced growth); (iii) the facet-type cracking is related to the formation of persistent fine slip bands that accompany no structural change of the matrix. On the basis of these results, the micromechanism of small crack growth and its relation to the concept of fatigue limit at the HCF regime is discussed in detail.