Effect of ultrasonic treatment on photoelectric and luminescent properties of ZnSe crystals

The results of the effect of ultrasonic treatment of ZnSe crystals on the structure of the energy spectrum of electronic states of centers with deep levels forming photoelectric and luminescent properties of this compound are presented. It is for the first time proved experimentally that the climb of edge dislocations under the effect of ultrasound leads to regrouping and generation of defects forming deep levels, which manifest themselves in phenomena of photosensitivity and radiative recombination.     

Grouped Approach for the Design of H.264/AVC Motion Estimation Architectures

This letter presents a novel approach for organizing computational resources into groups within H.264/AVC motion estimation architectures, leading to reductions of up to 75% in the equivalent gate count with respect to state‐of‐the‐art designs.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Reflectarray research at the communications research centre Canada

It has been a decade since a research program began on reflectarray technology at the Communications Research Centre Canada (CRC). This endeavor has demonstrated the advantages and shortcomings of this technology, the issues that ought to be addressed, and future opportunities. This paper summarizes the outcome of this research in the context of projects that have been carried out, and the resulting insight into reflectarray technology. Design methodology, fabrication process, and measurements results will be briefly discussed for each particular development.     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry     

Effective factors on synthesis of the hematite–silica red inclusion pigment

The work focuses on the synthesis of a red ceramic pigment by inclusion of hematite in a fumed silica matrix with different specific surface areas. Iron(II) sulfate was used as hematite precursor. Mixtures of iron(II) sulfate and fumed silica with different mole ratios were heated at different temperatures from 1000 to 1300 °C for 4 h.     

Identification of the temperature field and stresses in a thermosensitive cylinder according to the surface strains

We identify the time dependence of temperature of a surface of a long hollow thermosensitive cylinder and its thermal and thermal stressed states according to the known temperature and strains on the other surface. The posed problem is reduced to the inverse problem of thermoelasticity. By using the solution of the direct problem of thermoelasticity, we perform the numerical verification of the proposed procedure of solution of the inverse problem. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 43, No. 6, pp. 55–61, November–December, 2007.     

Pre-Attentive and Attentive Detection of Humans in Wide-Field Scenes

We address the problem of localizing and obtaining high-resolution footage of the people present in a scene. We propose a biologically-inspired solution combining pre-attentive, low-resolution sensing for detection with shiftable, high-resolution, attentive sensing for confirmation and further analysis. The detection problem is made difficult by the unconstrained nature of realistic environments and human behaviour, and the low resolution of pre-attentive sensing. Analysis of human peripheral vision suggests a solution based on integration of relatively simple but complementary cues. We develop a Bayesian approach involving layered probabilistic modeling and spatial integration using a flexible norm that maximizes the statistical power of both dense and sparse cues. We compare the statistical power of several cues and demonstrate the advantage of cue integration. We evaluate the Bayesian cue integration method for human detection on a labelled surveillance database and find that it outperforms several competing methods based on conjunctive combinations of classifiers (e.g., Adaboost). We have developed a real-time version of our pre-attentive human activity sensor that generates saccadic targets for an attentive foveated vision system. Output from high-resolution attentive detection algorithms and gaze state parameters are fed back as statistical priors and combined with pre-attentive cues to determine saccadic behaviour. The result is a closed-loop system that fixates faces over a 130 deg field of view, allowing high-resolution capture of facial video over a large dynamic scene.     

Sensitometric characteristics of an all‐solid‐state photoelectrochromic pixel for an electrochromic light‐addressable display

Abstract— An all solid‐state photoelectrochromic element (PECE) was developed on the basis of electrochromic layers of WO₃ and polyaniline with a layer of polymer electrolyte placed on a base of polyamidosulfoacid, in which a thin‐film CdS_xSe_1?x photoresistor was used as an electronic key. The dependence of the sensitometric characteristics of the PECE on the applied voltage was studied.