Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Formation of phase structure and crystallization behavior in blends containing polystyrene–polyethylene block copolymers

The microphase separation structure in the molten state and the structure formation in crystallization from such ordered melt were investigated for the blends of polystyrene–polyethylene block copolymers (SE) with polystyrene homopolymer (PS) and polyethylene homopolymer (PE) and for the blends consisting of two kinds of SE with different copolymer compositions from each other, using synchrotron small-angle X-ray scattering techniques (SAXS). The copolymer compositions of SE block copolymers employed were 0.34, 0.58 and 0.73 wt. fraction of PE, and their melt morphologies were cylindrical, lamellar and lamellar, respectively. Macrophase separation or the morphology change in the melt occurred depending on the molecular weight and the blend composition, as reported so far. In crystallization from such macrophase-separated and microphase-separated melts, the melt morphology was completely kept for all the blends. Crystallization behavior was also investigated for the blends. The crystallization within the spherical and cylindrical domains surrounded by glassy PS was not observed for SE/PS blends. In the crystallization from the macrophase-separated melt, two exothermal peaks were observed in the DSC measurements, while a single peak was observed for other blends. For the blends with PS, the degree of crystallinity was depressed and the apparent activation energy of crystallization was high, compared to those for the corresponding neat SE. For SE/PE and SE/SE blends, those were changed depending on the blend composition.     

Scanning electron microscopy of nerve fibers in human fetal cochlea

The cochleas of four human fetuses ranging 22–25 weeks gestation were studied by scanning electron microscopy (SEM) for the purpose of obtaining a better understanding of the nerve fiber arrangement in the human ear. After critical point drying, the specimens were dissected and the floor of the tunnel of Corti and the outer wall of Nuel's space were exposed for observation. Upper cochlear turns, especially the apical turn, seemed to be still immature. Observed nerve fibers were classified into three types:

• 1 Spiral fibers: Fibers traveling basalward and following the shape of the cochlea were found in both the tunnel of Corti and Nuel's space and believed to be the afferent nerves responsible for innervating the outer hair cells
• 2 Radial fibers: radiating outward from the osseous spiral lamina—one such radial fiber transversing high in the tunnel space (supposedly the efferent nerve servicing the outer hair cells), and another sort of radial fiber (found crossing the tunnel floor), the nature of which was uncertain.
• 3 Irregular fibers: Consisting of thin, randomly running fibers within the cochlea. The destination of these fibers was not determined, but possibly they represent transitory nerve branchings of afferent or more probably efferent nerves, which would later regress during maturation.

     

Corrosion behavior of wire-arc-sprayed stainless steel coating on mild steel

The corrosion characteristics of a wire-are-sprayed stainless steel coating on mild steel have been investigated in regards to atomizing gases and sealing treatment. Salt spray test was performed. The corrosion behavior of the coating was observed under a microscope succesively through a cycling test of wetting and drying in a salt solution. The sealing-treated coating was found to rust faster compared with the non-sealing-treated coating; it protected the mild steel substrate against corrosion, but even it deteriorated the coating itself due to the interruption of the substrate as an anode. The air-atomized coating ruste more heavily than the nitrogen-atomized one. Four different phases were observed in the coating in regards to corrosion behavior; namely, chromium-based oxide, iron-based oxide, chromium-depleted metallic phase, and stainless steel matrix phase. It was found that the chromium-depleted metallic phase and the iron-based oxide are non-corrosion-resistant, whereas the chromium-based oxide and the stainless steel matrix phase are corrosion-resistant.     

Fault tolerant approach for biosignal-based robot control

This paper proposes a fault tolerant framework for biosignal-based robot control with multiple sensor electrodes. In this approach, to cope with sensor faults, a reliable joint torque estimation model is selected from a group of estimation models based on sensor failure classifiers. The correlation among the electromyography (EMG) signal streams is used as input feature vectors for fault detection. To validate our proposed method, we artificially disconnect an EMG electrode or detach one side of an EMG probe from the skin surface during elbow-joint torque estimation experiments with five participants. When one EMG sensor electrode experiences one of the problems, the experimental results show that the joint torque can be estimated with significantly fewer errors using our proposed approach than a joint torque estimation method without sensor fault detection or than a method with a conventional sensor fault detection algorithm. Furthermore, we controlled a mannequin-arm-attached one-DOF exoskeleton based on the estimated torque profiles by generating movements with the estimated torque derived from the selected model.     

Implicit Formulation for SPH‐based Viscous Fluids

We propose a stable and efficient particle‐based method for simulating highly viscous fluids that can generate coiling and buckling phenomena and handle variable viscosity. In contrast to previous methods that use explicit integration, our method uses an implicit formulation to improve the robustness of viscosity integration, therefore enabling use of larger time steps and higher viscosities. We use Smoothed Particle Hydrodynamics to solve the full form of viscosity, constructing a sparse linear system with a symmetric positive definite matrix, while exploiting the variational principle that automatically enforces the boundary condition on free surfaces. We also propose a new method for extracting coefficients of the matrix contributed by second‐ring neighbor particles to efficiently solve the linear system using a conjugate gradient solver. Several examples demonstrate the robustness and efficiency of our implicit formulation over previous methods and illustrate the versatility of our method.     

A new optical elasticity resin for mobile LCD modules

Abstract— The display used in current cell phones has an air gap between the cover glass and the liquid‐crystal‐display (LCD) module to prevent the LCD glass from being damaged. Reflections at the boundaries of the air gap cause a reduction in the LCD luminance and contrast. To address this problem, a newly proposed LCD structure has been investigated. The “Super View Resin (SVR),” a transparent elastic resin which improves the shock resistance and visibility of the LCD, has been developed. Filling the air gap between the cover glass and LCD module with a refractive‐index‐matching resin solves the light‐reflection problem inherent in the use of a reinforced cover‐glass lens. Moreover, the elastic filler works as a damper, reducing any external shock, which prevents not only the cover glass and LCD module from being damaged, but also the glass from being shattered when it is broken.     

Superconductivity in the tetragonal phase of La1.9Bi0.1CuO4+δ annealed under high oxygen pressure

We have investigated the relation between the crystal structure and superconductivity in La_1.9Bi_0.1CuO₄₊ , in which the phase separation observed in La₂CuO₄₊ is suppressed. A phase diagram in theT– plane is given for La_1.9Bi_0.1CuO₄₊ with excess oxygen. For very small values, the crystal structure is orthorhombic, and an orthorhombic-tetragonal phase transition occurs markedly at 0.03 in the measured temperature range between 13 and 293 K. Superconductivity is observed in the range of 0.04<<0.11. This is clear evidence thathigh-T _c superconductivity also appears in the tetragonal phase.