Co‐ordinated voltage control of DFIG wind turbines in uninterrupted operation during grid faults

Emphasis in this article is on the design of a co‐ordinated voltage control strategy for doubly fed induction generator (DFIG) wind turbines that enhances their capability to provide grid support during grid faults. In contrast to its very good performance in normal operation, the DFIG wind turbine concept is quite sensitive to grid faults and requires special power converter protection. The fault ride‐through and grid support capabilities of the DFIG address therefore primarily the design of DFIG wind turbine control with special focus on power converter protection and voltage control issues. A voltage control strategy is designed and implemented in this article, based on the idea that both converters of the DFIG (i.e. rotor‐side converter and grid‐side converter) participate in the grid voltage control in a co‐ordinated manner. By default the grid voltage is controlled by the rotor‐side converter as long as it is not blocked by the protection system, otherwise the grid‐side converter takes over the voltage control. Moreover, the article presents a DFIG wind farm model equipped with a grid fault protection system and the described co‐ordinated voltage control. The whole DFIG wind farm model is implemented in the power system simulation toolbox PowerFactory DIgSILENT. The DFIG wind farm ride‐through capability and contribution to voltage control in the power system are assessed and discussed by means of simulations with the use of a transmission power system generic model developed and delivered by the Danish Transmission System Operator Energinet.dk. The simulation results show how a DFIG wind farm equipped with voltage control can help a nearby active stall wind farm to ride through a grid fault, without implementation of any additional ride‐through control strategy in the active stall wind farm. Copyright © 2006 John Wiley &Sons, Ltd.     

Compound-specific chlorine isotope analysis: a comparison of gas chromatography/isotope ratio mass spectrometry and gas chromatography/quadrupole mass spectrometry methods in an interlaboratory study

Chlorine isotope analysis of chlorinated hydrocarbons like trichloroethylene (TCE) is of emerging demand because these species are important environmental pollutants. Continuous flow analysis of noncombusted TCE molecules, either by gas chromatography/isotope ratio mass spectrometry (GC/IRMS) or by GC/quadrupole mass spectrometry (GC/qMS), was recently brought forward as innovative analytical solution. Despite early implementations, a benchmark for routine applications has been missing. This study systematically compared the performance of GC/qMS versus GC/IRMS in six laboratories involving eight different instruments (GC/IRMS, Isoprime and Thermo MAT-253; GC/qMS, Agilent 5973N, two Agilent 5975C, two Thermo DSQII, and one Thermo DSQI). Calibrations of (37)Cl/(35)Cl instrument data against the international SMOC scale (Standard Mean Ocean Chloride) deviated between instruments and over time. Therefore, at least two calibration standards are required to obtain true differences between samples. Amount dependency of δ(37)Cl was pronounced for some instruments, but could be eliminated by corrections, or by adjusting amplitudes of standards and samples. Precision decreased in the order GC/IRMS (1σ ≈ 0.1‰), to GC/qMS (1σ ≈ 0.2-0.5‰ for Agilent GC/qMS and 1σ ≈ 0.2-0.9‰ for Thermo GC/qMS). Nonetheless, δ(37)Cl values between laboratories showed good agreement when the same external standards were used. These results lend confidence to the methods and may serve as a benchmark for future applications.     

Parallel kinematic concept for stationary high performance cutting in wood machining centers

In recent years parallel kinematic machines for wood machining have come into use more frequently. Despite first promising prototypes, these machines are single solutions for specific applications. To meet the requirements of shorter product life cycles and higher product diversity, high flexibility is demanded of the machining system. This paper presents a new wood machining center obtaining both, the reduction of the primary and secondary processing times. The machine concept, based on a parallel kinematic structure, allows high operating speeds and accelerations not only for workpiece machining but also for handling. Thus, the machine can be used without any external handling devices. The kinematic structure originates from a plane closed five-bar chain with two linear drives and additional drive axes for stroke and rotation. In order to increase the useable workspace a continuous motion between different assembly modes is realized. To guarantee a high feed rate and to minimize set-up times, an optimized dust exhaustion is included.     

Decentralized array processing using the MODE algorithm

Centralized methods for source location using sensor arrays have computational and communication burdens that increase significantly with the number of sensors in the array. Therefore, these methods may not be usable in the applications involving very large arrays. In such applications, the data processing may need to be decentralized. This paper introduces two methods for decentralized array processing, based on the recently proposed MODE algorithm. For prescribed nonoverlapping subarrays, both methods are shown to be statistically optimal in the sense that asymptotically they provide the most accurate decentralized estimates of source location parameters. The problem of subarray selection to further optimize the estimation accuracy is only briefly addressed. The two methods are intended for different types of applications: the first should be preferred when there exist significant possibilities for local processing or for parallel computation in the central processor; otherwise the second method should be preferred. The accuracy of the two decentralized methods is compared to the centralized Cramér-Rao bound, both analytically and numerically, in order to provide indications about the loss of accuracy associated with decentralized processing.The work of P. Stoica was supported by a grant from the Royal Swedish Academy of Engineering Sciences and by the Swedish Research Council for Engineering Sciences under contract 91-676. The work of A. Nehorai was supported by the Air Force Office of Scientific Research under grant no. AFOSR-90-0164, and by the Office of Naval Research under grant no. N00014-91-J-1298.on leave at the Department of Applied Electronics, Chalmens University of Technology, 2-41296 Göthensberg, Sweeden.     

Rekonstruktion von Barockspiegeln des Historischen Grünen Gewölbes im Dresdener Schloss

Reconstruction of Baroque Mirrors of the Historical Green Vault in the Dresden Royal Palace On the 1^st September 2006 the Federal Chancellor Dr. Angela Merkel inaugurated the reconstructed Historical Green Vault, the treasury museum of the Saxon electors and kings. Since its destruction on 13^th February 1945 two generations have been working scientific‐artistically in order to set the course for its reconstruction. The idea of a baroque mirror chamber has firstly been implemented on a sequence of 8 rooms in the Green Vault. The original mirrors, which were covered with tin amalgam, had a considerably lower reflexivity modern day silver mirrors. From originally 423 m² mirror surface, only 60 m² could be reused. For the restoration and reconstruction of the original mirrors extensive analytic investigations became necessary, which the state‐owned company Sächsisches Immobilien‐ und Baumanagement (SIB) commissioned the Fraunhofer Institute for Electron Beam and Plasma Technology (FEP). On basis of these results the responsible restoration commission decided to replace partly destroyed mirror surfaces using the historical tin amalgam mirror technology. The fully destroyed jewel room would be restored with mirrors including partial gold etching. Due to hygienical and temporal reasons those mirrors were coated through a mercury‐free vacuum thin film technology ‐ the magnetron sputtering. The results show that a layer system consisting of tin‐bronze‐titanium and protective lacquers represent an adequate replacement for the original tin amalgam mirrors. The procedure allows relatively uncomplicated partial silverings and a subsequent inserting of artistic gold etchings.     

Don't underestimate the problems of user centredness in software development projectsthere are many!

. On the basis of a longitudinal field study of 29 commercial software development projects, the pros and cons of user centredness in software development were analysed. We looked at two concepts: user participation-an organizational device-involving a user representative in the team, and user orientation-a cognitive-emotional concept-which pertains to positive attitudes towards users. Both were found to be associated with project difficulties relating to process and product quality as well as overall project success. We suggest that the issue is no longer whether or not to involve users, but instead to develop a realistic understanding of the difficulties associated with user centredness.