Ozone Generator with Cylindrical Type of Rotating Electrode

An ozone generator using a rotating electrode to improve ozone generation efficiency is proposed. The ozone generator electrode unit consists of a rotating electrode and fixed electrode. The rotating electrode has the grounded 36 pieces of tungsten wires fixed in parallel to the rotation axis on the rotating cylinder surface. A dielectric electrode is used as a fixed electrode located on the inside of the tube of the electrode unit. The width of the apparent discharge gap is 1mm. Alternating current with a frequency of 50 Hz is applied to the electrode unit. The rotation speed can be adjusted from 0 rpm to 1200 rpm by a variable speed motor. Oxygen gas is used as the material gas. Higher ozone concentration and higher ozone generation efficiency are obtained compared with that when the rotation speed is 0 rpm. The gas temperature is measured at the inlet and outlet of the ozone generator, and the rotation speed for the cooling effect is most effective at about 500 rpm. The maximum generation efficiency is estimated to be 61 g/kWh at 800 rpm, and this value is twice as large as in the case of 0 rpm.     

Guinea pig bone marrow cells treated with platelet-activating factor generate factor(s) which affects their DNA synthesis and microbicidal activity

We have previously reported that platelet-activating factor (PAF) induces proliferation and microbicidal activity of guinea pig bone marrow cells. In the present study, we have found that the conditioned medium of PAF- or nonmetabolizable PAF agonist-treated guinea pig bone marrow cells augmented DNA synthesis and induced microbicial activity of bone marrow cells. A PAF specific antagonist, CV-6209, inhibited generation of the active conditioned medium by PAF. Addition of the PAF antagonist only partially suppressed the augmentative effect of the active conditioned medium on DNA synthesis; this is consistent with the fact that, because of the rapid breakdown, no appreciable amount of PAF remained in the conditioned medium of PAF-treated cells. Although mouse bone marrow cells did not respond to PAF unlike guinea pig cells, their DNA synthesis was significantly enhanced by the conditioned medium of PAF-treated guinea pig bone marrow cells. Thus, some newly generated factor(s) distinct from the originally inoculated PAF seemed to modulate the bioactions of PAF on bone marrow cells. An appreciable amount of PAF was produced by calcium ionophore-treated guinea pig bone marrow cells. These findings indicate that PAF synthesized in guinea pig bone marrow cells induces generation in the cells of some factor(s) which affects proliferation or microbicidal activity. Presented at The Third International Conference on Platelet-Activating Factor and Structurally Related Ether Lipids, Tokyo, Japan, May 1989.     

Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Relationships between hydrogen donor abilities and chemical structure of aromatic compounds in terms of coal liquefaction

To obtain fundamental information about hydrogen transfer, the relationships between hydrogen donor ability and chemical structure of model compounds representing donor solvents is studied using gas chromatography,¹H n.m.r. and computing calculation methods. The order of the model compounds in terms of the ability as donor solvent to release hydrogen is: decalin < tetralin < 1,2-dihydronaphthalene < < 1,4-dihydronaphthalene. This trend closely correlates with the difference in binding energies of the hydroaromatic compounds and their radicals, determined by intermediate neglect of differential overlap (INDO) calculation. Electron spin resonance spectroscopy (e.s.r.) confirms that radical species are created after heat-treatment of the donor compounds. The ability of model compounds representing coal to accept hydrogen is assessed from a comparison of the¹H n.m.r. spectra. It is established that donor and acceptor efficacies are dependent upon chemical structure.     

Elastoplastic Finite Element Analysis and Strength Evaluation of Adhesive Butt Joints of Similar and Dissimilar Hollow Shafts Subjected to External Bending Moments

Stress distributions and deformation of adhesive butt joints are analyzed by an elastoplastic finite element method when the joints of similar and dissimilar shafts are subjected to external bending moments. The effects of the ratio of Young's modulus for the adherends to that for an adhesive and the effects of the adhesive thickness on the interface stress distribution are investigated. Joint strength is predicted by using the elastoplastic interface stress distributions. It is found that the singular stress at the edge of the interfaces increases with an increase of the ratio of Young's modulus. Measurement of strains in joints and experiments on joint strength were conducted. The numerical results are in fairly good agreement with the experimental results. It is observed that the joint strength for dissimilar shafts are smaller than those for similar shafts. A fracture of dissimilar adhesive up-bonded shafts occurred from the interface of the adherend with smaller Young's modulus. It is seen that joint strength increases as the adhesive thickness increases.     

Dehydrogenative Cracking of n-Butane over Modified HZSM-5 Catalysts

Dehydrogenative cracking reaction of n-butane was studied using HZSM-5 catalyst modified with various metal oxides. Alkaline earth (magnesium), transition metal (cobalt) and rare earth (lanthanum) elements are used for the modification. The selectivity of the products was studied at low conversion (20%). Methane, ethane, ethylene, propylene, butenes and butadiene were the main products. With the use of the cobalt- or magnesium-containing HZSM-5, dehydrogenative cracking was observed and the selectivity of ethylene was much larger than that of ethane. On the other hand, the selectivity of ethylene and ethane were almost the same in the reaction using the lanthanum-containing HZSM-5. It is considered that the cobalt- and magnesium-loaded sites on HZSM-5 played an important role in the dehydrogenative cracking.     

Prediction model of surface residual stress within a machined surface by combining two orthogonal plane models

The variation of surface residual stress within a machined surface layer caused by face turning was studied. The size of the tool’s corner radius and the feed rate affect residual stress. A process model using the finite element method is proposed and the mechanical effects of the corner radius and feed rate on a machined surface were discussed. When a tool with a small corner radius is used, surface residual stress perpendicular to the cutting direction becomes compression stress. As well, surface residual stress changes from tension to compression as the feed rate decreases. The process model consists of an orthogonal cutting simulation and an indentation-like simulation of a corner radius into a work piece surface. The simulated results show quantitative agreement with the residual stress measured experimentally. The integrity of the machined surface will be controlled more efficiently if the cutting conditions during finishing are determined with the proper consideration of the surface generating process.     

Novel process for cover glass with ideal stress distribution

Abstract — This paper proposes a new process to manufacture cover glass that overcomes a strength trade‐off between the face and the edge. In the process, alkali barrier films are deposited on glass faces before an ion exchange process in order to control face stress properties without inhibiting the edge strengthening. As a demonstration of the process, alkali‐alumino‐silicate glass sheets with sputter‐deposited SiO₂ films were chemically strengthened, and then their stress properties and strengths were investigated. As a result, thicker SiO₂ films cause lower face DOL (depth of strengthened layer), and it is observed that the faces have lower DOL than the edges. In strength tests corresponding to major fracture modes of smartphone cover glass, specimens with 80–100 nm films have more balanced face performance and better edge impact strengths than the no‐film specimen.