Numerical simulation of tip leakage vortex effect on hydrogen-combustion flow around 3D turbine blade

In these years, a lot of environmental problems such as air pollution and exhaustion of fossil fuels have been discussed intensively. In our laboratory, a hydrogen-fueled propulsion system has been researched as an alternative to conventional systems. A hydrogen-fueled propulsion system is expected to have higher power, lighter weight and lower emissions. However, for the practical use, there exist many problems that must be overcome. Considering these backgrounds, jet engines with hydrogen-fueled combustion within a turbine blade passage have been studied. Although some studies have been made on injecting and burning hydrogen fuel from a stator surface, little is known about the interaction between a tip leakage vortex near the suction side of a rotor tip and hydrogen-fueled combustion. The purpose of this study is to clarify the influence of the tip leakage vortex on the characteristics of the 3-dimensional flow field with hydrogen-fueled combustion within a turbine blade passage. Reynolds-averaged compressible Navier-Stokes equations are solved with incorporating a k-ε turbulence and a reduced chemical mechanism models. Using the computational results, the 3-dimensional turbulent flow field with chemical reactions is numerically visualized, and the three-dimensional turbulent flow fields with hydrogen combustion and the structure of the tip leakage vortex are investigated.     

Impacts of air bleeding on membrane degradation in polymer electrolyte fuel cells

A long-term accelerated test (4600 h) of a 25 cm² single cell with excess air bleeding (5%) was carried out to investigate the effects of air bleeding on membrane degradation in polymer electrolyte fuel cells. The rate of membrane degradation was negligibly low (fluoride-ion release rate = 1.3 × 10⁻¹⁰ mol cm⁻² h⁻¹ in average) up to 2000 h. However, membrane degradation rate was gradually increased after 2000 h. The CO tolerance of the anode gradually dropped, which indicated that the anode catalyst was deteriorated during the test. The results of the rotating ring–disk electrode measurements revealed that deterioration of Pt–Ru/C catalyst by potential cycling greatly enhances H₂O₂ formation in oxygen reduction reaction in the anode potential range (∼0 V). Furthermore, membrane degradation rate of the MEA increased after the anode catalyst was forced to be deteriorated by potential cycling. It was concluded that excess air bleeding deteriorated the anode catalyst, which greatly enhanced H₂O₂ formation upon air bleeding and resulted in the increased membrane degradation rate after 2000 h.     

Experimental study on latent heat storage characteristics of W/O emulsion -Supercooling rate of dispersed water drops by direct contact heat exchange-

Recently, much attention has been paid to investigate the latent heat storage system. Using of ice heat storage system brings an equalization of electric power demand, because it will solved the electric -power-demand-concentration on day-time of summer by the air conditioning. The flowable latent heat storage material, Oil/Water type emulsion, microencapsulated latent heat material-water mixture or ice slurry, etc., is enable to transport the latent heat in a pipe. The flowable latent heat storage material can realize the pipe size reduction and system efficiency improvement. Supercooling phenomenon of the dispersed latent heat storage material in continuous phase brings the obstruction of latent heat storage. The latent heat storage rates of dispersed water drops in W/O (Water/Oil) emulsion are investigated experimentally in this study. The water drops in emulsion has the diameter within 3 ～ 25μm, the averaged water drop diameter is 7.3μm and the standard deviation is 2.9μm. The direct contact heat exchange method is chosen as the phase change rate evaluation of water drops in W/O emulsion. The supercooled temperature and the cooling rate are set as parameters of this study. The evaluation is performed by comparison between the results of this study and the past research. The obtained experimental result is shown that the 35K or more degree from melting point brings 100% latent heat storage rate of W/O emulsion. It was clarified that the supercooling rate of dispersed water particles in emulsion shows the larger value than that of the bulk water.     

Experiment and analysis of practical-scale solar pond stabilized with salt gradient

A large-scale solar pond with salty water was constructed in the suburbs of Kitami in 1985. Its performance has been measured and analyzed by the authors after that. The solar pond body is circular of 44 m diameter, and the pond water is of 3 min total depth. After, 15 months, the depth of the salt gradient zone (S.G.Z.) was thinned by 10 cm in the top and by 20 cm in the bottom due to convection of the top and bottom zones. The temperature in the convective storage zone (C.S.Z.) reached 70°C, its maximum, at the beginning of September in 1985, however, it was not as high in 1986 due to contamination of the pond water. The temperature of the storage zone was reduced from November to April due to ice covering on the pond surface. The collected heat yielded largely and the collection efficiency reached more than 30% in summer, but decreased to negative values in winter. The thermal performance of the solar pond was predicted by a simulation calculation, and the calculated result compared well with the measurements.     

Si thin platelets as high-capacity negative electrode for Li-ion batteries

Pure Si platelets and Ni or Cu layer-laminated Si platelets with difference thickness were prepared, and their charge/discharge properties were examined in 1 M LiClO₄/EC + DEC (1:1 by volume) as alternative negative electrode materials to graphite for Li-ion batteries. The shape of thin platelets and lamination with Ni layer are significantly effective to improve the cycleability in Li-Si alloy system by relieving the stress during the alloying/de-alloying processes, reinforcing the mechanical strength and reducing the Li⁺ ion diffusion length. Moreover, the first irreversible capacity is minimized by reduction of the amount of Ketjen Black (KB) in the composite electrode because of electrolyte decomposition on the surface of KB. Consequently, the Si/Ni/Si-LP30 (30/30/30 nm) composite electrode with 5 wt% KB also exhibits over 700 mAh g⁻¹ even after 50 cycles in 1 M LiPF₆/EC + DEC (1:1).     

Theoretical analysis of transient recovery voltages when clearing a transformer secondary fault

An analytical formula for the transient recovery voltage and its derivative dv/dt across a circuit breaker has been derived for the case of a transformer secondary fault. A comparison of the calculated results with field test and EMTP simulation results has demonstrated it to have satisfactory accuracy. By applying the formula, the effects of various circuit parameters on the transient recovery voltage and its derivative dv/dt are elucidated. The derivative dv/dt, defined conventionally as the ratio of the crest value and the time to the crest, is found to be about two‐thirds of the maximum value of dv/dt given as a function of time. In addition, a formula for the critical circuit parameters at which dv/dt across a vacuum circuit breaker reaches the critical condition, that is, the circuit breaker fails to interrupt a fault current, is derived. © 2000 Scripta Technica, Electr Eng Jpn, 134(3): 44–52, 2001     

Field test and EMTP simulation of transient voltages when clearing a transformer secondary fault

A field test was carried out to investigate a fault clearing transient due to current interruption of a three‐phase to ground fault at the secondary side of a 3‐MVA, 22/6.6‐kV transformer by a vacuum circuit breaker. EMTP simulations in comparison with the measured results have made it clear that the capacitance C_p of a CR divider to measure voltages reduces dv/dt of transient recovery voltage across the circuit breaker by the ratio of (C_t/(C_t + C_p) where C_t is the transformer stray capacitance. The leakage inductance evaluated from the transformer rating has been found to be noticeably greater than that determined from the measured fault current possibly due to the transformer saturation. Considering the transformer magnetizing conductance and selecting an appropriate interrupted current, EMTP simulation gives a satisfactory result compared with a field test. © 1999 Scripta Technica, Electr Eng Jpn, 130(2): 40–48, 2000     

Convective heat transfer of horizontal spherical particle layer heated from below and cooled from above Part II: Effect of thickness of particle layer

Convection heat transfer and pressure drop measurements were performed with a rectangular duct, having a cooled upper and a heated lower surface, which was packed with spherical particles. Air was used as the test fluid and four kinds of spherical particles having different diameters and thermal conductivities were used as the packing materials. The ratio of the diameter of the spherical particle to the distance between the cooled and heated surfaces, d/H, was varied from 0.173 to 1. The thermal conductivity of the particle layer was also measured under the still air condition. The thermal conductivity of the particle layer was not affected by the value of d/H. In the case of the one-stage arrangement of spherical particles (d/H = 1), the flow resistance took on a remarkably small value compared with the flow resistance of a homogeneous spherical particle layer. Moreover, the flow resistance of the particle layer formed with some layers of particles could be predicted by combining the flow characteristics of the one-stage particle layer and that of the homogeneous spherical particle layer. The heat transfer coefficient of the particle layer was larger than that of turbulent air flow on a flat plate. At a constant superficial air velocity, there existed a value of d/H which gave a maximum value of the average heat transfer coefficient. Nondimensional heat transfer correlation equations were derived in terms of parameters expressing the average characteristics of the spherical particle layers. © 1998 Scripta Technica, Heat Trans Jpn Res, 26(3): 176–192, 1997     

A regulatory role for recombinase activating genes, RAG-1 and RAG-2, in T cell development

Effects of etoposide (VP-16) and cytosine arabinoside (Ara-C) on the cell cycle of HL-60 and THP-1 cells were studied by flow cytometry using the bromodeoxyuridine (BrdU)/DNA assay technique to investigate the efficacy of VP-16 for monocytic leukemia cells. VP-16 inhibited the proliferation of THP-1 cells more strongly than that of HL-60 cells at any concentrations used at 24 and 48 hr. VP-16 arrested HL-60 and THP-1 cells in the G2/M phase and reduced them in the G0/G1 and early S phase at higher concentrations. There was no significant difference in the percentage of G2/M phase cells at the same concentration between both cells. However, reduction in the G0/G1 and early S phase cells was more marked in THP-1 than HL-60 cells significantly. On the other hand, Ara-C perturbed the cell cycle of HL-60 cells more than that of THP-1 cells at 24 and 48 hr. These results suggest that the effects of VP-16 on the cell cycle may be more intense in THP-1 than HL-60 cells, and support the efficacy of VP-16 for treating monocytic leukemia in vivo.     

Is outer arm dynein intermediate chain 1 multifunctional?

The outer arm dynein of sea urchin sperm axoneme contains three intermediate chains (IC1, IC2, and IC3; M(r) 128,000, 98,000, and 74,000, respectively). IC2 and IC3 are members of the WD family; the WD motif is responsible for a protein-protein interaction. We describe here the molecular cloning of IC1. IC1 has a unique primary structure, the N-terminal part is homologous to the sequence of thioredoxin, the middle part consists of three repetitive sequences homologous to the sequence of nucleoside diphosphate kinase, and the C-terminal part contains a high proportion of negatively charged glutamic acid residues. Thus, IC1 is a novel dynein intermediate chain distinct from IC2 and IC3 and may be a multifunctional protein. The thioredoxin-related part of IC1 is more closely related to those of two redox-active Chlamydomonas light chains than thioredoxin. Antibodies were prepared against the N-terminal and middle domains of IC1 expressed as His-tagged proteins in bacteria. These antibodies cross-reacted with some dynein polypeptides (potential homologues of IC1) from distantly related species. We propose here that the three intermediate chains are the basic core units of sperm outer arm dynein because of their ubiquitous existence. The recombinant thioredoxin-related part of IC1 and outer arm dyneins from sea urchin and distantly related species were specifically bound to and eluted from a phenylarsine oxide affinity column with 2-mercaptoethanol, indicating that they contain vicinal dithiols competent to undergo reversible oxidation/reduction.