Temperature and pressure effects on supercritical CO2 extraction of tomato seed oil

Tomato seed oil was extracted with supercritical carbon dioxide in a semibatch-flow extractor within the temperature range 313–343 K and the pressure range 10.8–24.5MPa. The extraction rates increased with pressure, but decreased with temperature increase because of the variation in solvent density and resultant differences in oil solubility. The fatty acid composition of the extracted oil was similar to that of soybean oil.     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.     

Properties of indium oxide/tin oxide multilayered films prepared by ion-beam sputtering

The preparation and characterization of indium oxide (InO _x )/tin oxide (SnO _y ) multilayered films deposited by ion-beam sputtering are described and compared with indium tin oxide (ITO) films. The structure and the optoelectrical properties of the films are studied in relation to the layered structures and the post-deposition annealing. Low-angle X-ray diffraction analysis showed that most films retained the regular layered structures even after annealing at 500° C for 16 h. As an example, we obtained a resistivity of 6×10^–4 cm and a transparency of about 85% in the visible range at a thickness of 110 nm in a multilayered film of InO _x (2.0 nm)/SnO _y (0.2 nm)×50 pairs when annealed at 300° C for 0.5 h in air. Hall coefficient measurements showed that this film had a mobility of 17 cm² V^–1 sec^–1 and a carrier concentration (electron density) of 5×10²⁰ cm^–3.     

Modification of mesophase pitch by blending Part 2 Modification of mesophase pitch fibre precursor with thermoresisting polyphenyleneoxide (PPO)

Polyphenyleneoxide was blended in amounts of 5 or 10 wt% into petroleum-derived mesophase pitch to reinforce the pitch fibre before the oxidative stabilization to achieve better handling properties. Although polyphenyleneoxide was fusible but hardly soluble in the mesophase pitch even at a spinning temperature of 350° C, blended pitch could be smoothly spun into pitch fibre 10m diameter, as could the parent pitch. Fibrous polyphenyleneoxide of less than 1m diameter was homogeneously dispersed in the pitch fibre, being arranged along the fibre axis. Such fibrous polyp henyleneoxide reinforced the pitch fibre considerably. The fibrous substances at the centre of the fibre disappeared in the carbonized fibre at 1300° C after oxidation at 250° C, although some short ones were observed in the skin region of the fibre, suggesting that polyphenyleneoxide was co-carbonized to be assimilated with mesophase pitch at the centre of the fibre, where the effects of oxidation may be rather limited. The oxidation reactivity and its mechanical strength after carbonization were slightly lower in comparison with those of the parent mesophase pitch.     

Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Surface segregation of siloxane containing component in polysiloxane‐block‐polyimide and s‐BPDA/ODA polyimide blends

Surface segregation in polymer blend systems between 3,3′,4,4′‐biphenyltetracarboxylic dianhydride/4,4′‐diaminodiphenyl ether (s‐BPDA/ODA) polyimide and block copolymer based on polysiloxane‐block‐polyimide (SPI) has been investigated. These polyimide blends, having various compositions of the SPI, were processed by a solution casting method. The glass substrate used in the film‐casting process shows significant effect on the migration of surface segregated species to enrich the air‐exposed surface, whereas the more polar s‐BPDA/ODA tends to remain close to the polar glass substrate. X‐ray photoelectron spectroscopy reveals that even at low SPI concentration, the siloxane moieties in the block copolymer tend to segregate into the air side surface. Contact angle measurement evidently indicates an enrichment of the hydrophobic siloxane fraction on the blend film surface. The average water contact angle of glass side surface is 77°C whereas that of the air side is about 102°C in every blend ratio. This behavior confirms the surface segregation phase separation in these polymer blends. Finally, the surface morphology observed by atomic force microscopy also suggests segregation type of phase separation in these blend systems. POLYM. ENG. SCI., 47:489–498, 2007. © 2007 Society of Plastics Engineers.     

Continual conversion of free fatty acid in rice bran oil to triacylglycerol by immobilized lipase

Rice bran oil containing 30–50% free fatty acid was continually converted to an oil containing more than 75% of triacylglycerol (TG) by means of immobilized lipase. The reaction was carried out at 60°C for 24 h with dehydration and reactant mixing by dry nitrogen flow under a positive nitrogen atmosphere. Enzymatic TG synthesis with evaporation by heating was not suitable because of the increasing peroxide value of the oil. Part of this article was presented at the annual meeting of the Japan Oil Chemists' Society at Sendai, Japan, October, 16, 1990.     

Effect of poly(acrylic acid) on the preparation of thick silica films by electrophoretic sol–gel deposition of re-dispersed silica particles

Thick silica films were prepared by the electrophoretic sol–gel deposition technique in the presence of poly(acrylic acid) (PAA) using monodispersed silica particles; the particles were prepared by the sol–gel method, pre-heat treated and then re-dispersed in the mixture of H2O and ethanol. The weight of deposited silica films was maximized when 0.2 mass % of PAA against the whole amount of sol was added. The particles constructing the thick silica films were packed densely when the amount of added PAA was less than 0.2 mass%. The weight of the film increased with decrease in the content of H2O in the sol when a fixed amount of PAA was added. After the heat treatment of deposited films at 800 °C, crack-free silica films of about 30 m thickness were prepared. © 1998 Chapman & Hall     

Magnetic probe array with high sensitivity for fluctuating field

A magnetic probe array is constructed to measure precisely the spatial structure of a small fluctuating field included in a strong confinement field that varies with time. To exclude the effect of the confinement field, the magnetic probes consisting of figure-eight-wound coils are prepared. The spatial structure of the fluctuating field is obtained from a Fourier analysis of the probe signal. It is found that the probe array is more sensitive to the fluctuating field with a high mode number than that with a low mode number. An experimental demonstration of the present method is attempted using a field-reversed configuration plasma, where the fluctuating field with 0.1% of the confinement field is successfully detected.