A comparison of the hydrolysis of sweet potato starch with β-amylase and infrared radiation allows prediction of reducing sugar production

The apparent reaction rate constants (k) of the reaction that generates reducing sugar (presented as mg maltose equivalents) from raw sweet potato starch by using β‐amylase were determined by varying enzyme concentration, starch concentration and pH. The Arrhenius plot of the k‐value reached a peak at approximately 86 °C; the activation energy and frequency factor were also determined. Moreover, the amount of reducing sugar produced in sweet potato heated by infrared irradiation was estimated by using the values of k and the kinetic parameters. The calculated amounts of reducing sugar produced generally agreed with the experimental values. These results indicate that the amount of reducing sugar produced in heat‐treated sweet potato can be predicted by the methodology described in this study.     

Near-IR sensitization of nanocrystalline TiO2 with a new ruthenium complex having a 2,6-bis(4-carboxyquinolin-2-yl)pyridine ligand

A new ruthenium(II)–polypyridine complex (1) having a 2,6-bis(4-carboxyquinolin-2-yl)pyridine ligand was synthesized as a sensitizer for dye-sensitized solar cells (DSCs). This complex exhibited remarkable light-harvesting properties in the near-IR region. DSCs sensitized with 1 showed a 35% incident photon-to-current conversion efficiency (IPCE) at 900 nm.     

Performance analysis on the liquid-ice thermal storage system for optimum operation

For the purpose of determining the optimum operation condition of liquid-ice thermal storage system, the performance analysis has been carried out. The target system was consisted of refrigerator, its auxiliary devices, liquid-ice production device, piping system, and thermal load section. The system performances were widely investigated analytically for the variety of operation conditions including the cycle performance of a refrigerator. The optimum operation condition of the liquid-ice thermal storage system from the viewpoint of coefficient of performance and the performance of heat release were discussed.     

Preparation and Properties of Glass-Ceramics Derived from Nitrogen-Containing β-Spodumene Glasses

Crystallization of Li-Al-Si-O-N oxynitride glasses based on the β-spodumene composition and the properties of the resultant glass-ceramics have been studied. The onset of the precipitation of metastable high-quartz solid solution and its transformation to β-spodumene shift to higher temperatures with increasing nitrogen content of the oxynitride glasses. Nitrided glass-ceramics crystallized at 1200°C have negative thermal expansion coefficients, since high-quartz structure is maintained up to 1000° and 1200°C. Knoop hardness and density of the glass-ceramics increase with increasing nitrogen content. There was evidence that part of the nitrogen atoms were incorporated into the high-quartz solid-solution structure and that a small amount of the minor phase of Si₂N₂O was precipitated in highly nitrided glass-ceramics.     

Transparent conducting film: Effect of mechanical stretching to optical and electrical properties of carbon nanotube mat

We describe in this paper a transparent conducting film (TCF). It is a fibrous layer of multiwalled carbon nanotubes (MWNTs), labeled a dilute CNT mat, that was prepared and unidirectionally stretched to improve both the optical and electrical properties. After stretching by 80% strain, transmittance at 550 nm wavelength was improved by 37% and sheet resistance was reduced to 71% of the original value. The improvement of the transmittance can be explained by increased area of the CNT mat after stretch, and the reduced sheet resistance can be explained by increased density of the CNT alignment in lateral direction due to contraction. Based on the microscopic observation before and after stretch, models to describe the phenomena are proposed. By further expanding on this method, it may be possible to obtain a transparent conducting carbon nanotube film which is crack-resistant for solar cell applications.     

Rapid erasing of wettability patterns based on TiO2-PDMS composite films

TiO₂-polydimethylsiloxane (TiO₂-PDMS) composite films are prepared using the sol–gel method from a Ti(OBu)₄–benzoylacetone solution containing PDMS. The prepared films are cured by irradiation with ultraviolet (UV) light. Structural changes in the films after UV irradiation are confirmed by UV–vis absorption experiments, which show that an absorption band characteristic of the benzoylacetonate chelate rings disappears. This finding is ascribed to structural changes associated with the dissociation of the chelate rings. The IR spectra of the thin films exhibit a broad absorption band after UV irradiation, indicating that a Ti–O–Ti network forms in the thin film. Contact angles are measured for the TiO₂-PDMS thin films, showing wettability conversion from hydrophobic to superhydrophilic states by irradiation with oxygen plasma for 1 s. This phenomenon is explained by XPS experiments which reveal that the number of carbon atoms decreases, whereas the number of oxygen atoms increases on the surface of the TiO₂-PDMS composite films. Finally, hydrophobic–superhydrophilic patterns are fabricated based on a patterned TiO₂-PDMS composite film. The film displays a rapid change to superhydrophilicity over the whole film surface upon plasma irradiation for 1 s, which means that the wettability patterns are rapidly erasable.     

Uniform culture in solid-state fermentation with fungi and its efficient enzyme production

Solid-state fermentation (SSF) has attracted a lot of interest for carrying out high-level protein production in filamentous fungi. However, it has problems such as the fermentation heat generated during the culture in addition to the reduced mobility of substances. These conditions lead to a nonuniform state in the culture substrate and result in low reproducibility. We constructed a non-airflow box (NAB) with a moisture permeable fluoropolymer membrane, thereby making it possible to control and maintain uniform and optimal conditions in the substrate. For the NAB culture in Aspergillus oryzae, temperature and water content on/in the whole substrate were more consistent than for a traditional tray box (TB) culture. Total weight after the culture remained constant and dry conditions could be achieved during the culture. These data demonstrate the possibility of growing a uniform culture of the whole substrate for SSF. The NAB is advantageous because it allows for the control of exact temperature and water content in the substrate during the culture by allowing vapor with latent heat to dissipate out of the box. In addition, several enzymes in the NAB culture exhibited higher production levels than in the TB culture. We believe that culturing in the constructed NAB could become a standard technique for commercial SSF.     

A maximum power point tracking for photovoltaic-SPE system using a maximum current controller

Processes to produce hydrogen from solar photovoltaic (PV)-powered water electrolysis using solid polymer electrolysis (SPE) are reported. An alternative control of maximum power point tracking (MPPT) in the PV-SPE system based on the maximum current searching methods has been designed and implemented.Based on the characteristics of voltage–current and theoretical analysis of SPE, it can be shown that the tracking of the maximum current output of DC–DC converter in SPE side will track the MPPT of photovoltaic panel simultaneously.This method uses a proportional integrator controller to control the duty factor of DC–DC converter with pulse-width modulator (PWM).The MPPT performance and hydrogen production performance of this method have been evaluated and discussed based on the results of the experiment.     

High-performance antireflective coatings with a porous nanoparticle layer for visible wavelengths

Ghosts and flares are well-known problems that are caused by reflections from lens surfaces when we take photographs. It is more difficult to prevent such stray light in a digital camera than in a film camera because of high reflectance from the low-pass filter and diffraction from the image sensor. To prevent such stray light, we introduce an ultralow refractive index layer into the antireflective (AR) coatings. We used the solgel method to form porous fluoride layers with ultralow refractive indices, and we succeeded in developing a unique process to form AR coatings with superior performance.