A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process     

A mechanism for transgranular stress-corrosion cracking

A model is proposed to explain transgranular-stress corrosion cracking (T-SCC) in face-centered cubic (fcc) materials. Crack propagation is shown to be anisotropic, in that growth near {110} < 001> is discontinuous due to crack arrest by dislocation blunting whereas growth away from this growth orientation is continuous. For the former case, renucleation of arrested cracks involves active dissolution of shear bands at the crack tip, which changes the stress state at Lomer-Cottrell locks, causing them to fail by cleavage. Once the crack is nucleated, its instantaneous macroscopic crack-growth velocity is considered to be comprised of multiple nucleation of microcracks with intervening arrests. This microcracking results from the interaction of the stress fields from neighboring cracks which are forming simultaneously, the crack-opening constraint due to ligaments which act as “bridges” behind the crack front, and the localized dissolution at the microcrack tip which affectsK _IC and leads to the “cobblestone” appearance. Experimental evidence and theoretical considerations are presented to support the model. The system studied was Cu-25 at. pct Au in 0.6 M NaCl solution at potentials between 300 and 400 mV (sce), which precludes hydrogen embrittlement. This article is based on a presentation made in the symposium “Quasi-Brittle Fracture” presented during the TMS fall meeting, Cincinnati, OH, October 21–24, 1991, under the auspices of the TMS Mechanical Metallurgy Committee and the ASM/MSD Flow and Fracture Committee.     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

异丙苯在Cu-HMS分子筛上的催化氧化

以含Cu的中孔分子筛(Cu-HMS)为催化剂,研究异丙苯的催化氧化。研究发现,Cu-HMS催化剂的加入使异丙苯氧化的诱导期显著缩短。在75℃下,以Cu-HMS为催化剂,O2为氧化剂的纯异丙苯氧化反应,苯乙酮为主要副产物,反应的选择性和转化率都很高。当催化剂用量为1 5×10-4mol/ml时,反应8h后,异丙苯转化率为32 7%,目的产物的累积浓度(质量分数)为37 7%,选择性为99%;反应12h后,异丙苯转化率为42 4%,目的产物的累积浓度为46 3%,选择性为95 6%。     

甲醇氧化羰化制碳酸二甲酯产物气相色谱分析

以Chromosorb 10 1为固定相 ,气相色谱法分析甲醇氧化羰化制碳酸二甲酯产物中水、甲醇、乙酸甲酯和碳酸二甲酯等组份的含量 ,考察了柱温 ,载气流量对分离度的影响 ,确定了适宜的分析条件 ,并用校正面积归一化法定量。该方法操作简便 ,快速 ,精度高 ,重现性好     

高速往复式内燃机平衡轴低质量设计分析

分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。扇形平衡重半径及宽度应尽量大、夹角应尽量小。偏心圆平衡重的偏心圆半径应尽可能大 ,轴承半径应尽可能小。同样质量的扇形平衡重产生的平衡力比偏心圆平衡重要大。     

分离式热管换热器在脱硫装置的应用

介绍了分离式热管换热器的工作原理及其在工业脱硫装置中的应用，并不其余热回收情况与传统的二次中热方法相比较，阐明了其节能及环保作用。     

悬停直升机的雷达探测技术

首先对直升机旋翼的雷达回波进行建模与分析,在此基础上分析了雷达探测悬停直升机的可能性,提出了一种适用于所有直升机类型的多扫描周期积累检测系统方案,讨论了可能影响其检测性能的因素.     

XAZ340-4GF反洗压滤机的研制与应用

介绍了XAZ340-4GF反洗压滤机的研制过程,介绍了该机型的结构\原理\工艺系统.并简要介绍了其工业应用情况。     

纳米α-FeOOH颗粒的形态和结构

以硫酸法钛白的副产物绿矾为原料，采用滴加法制备纳米铁黄（α－FeOOH）颗粒。研究了反应体系的pH值、反应温度、通氧速率、搅拌速率和添加剂等对铁黄颗粒形态结构的影响，采用XRD、TEM等分析手段对颗粒进行表征。结果表明，调节体系pH值能控制铁黄晶型结构和色相；改变通氧速率、搅拌速率、添加剂种类以及反应温度等可以调节纳米α－FeOOH的大小和分散性。