Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

无油分子泵机组的组装

介绍了将ALCATEL公司生产的一台ATPl00涡轮分子泵、一台MDP50ll牵引分子泵及一台VRC公司生产的lBy6型干泵组装成无油分子泵机组的过程。文中给出了泵间配合的计算、机组方案的设计、连接管路、仪器支架的设计及选择。本机组所采取的设计方案使三个泵都最大限度地发挥了优点避免了缺陷，较好地满足了使用要求，为今后选购单泵和组装无油分子泵机组提供了可靠的理论和实验依据。     

深井长裸眼跨隔测试新工艺的应用

为减少勘探费用，缩短施工周期，取全取准各项地质资料，采取中途测试工艺。随着深井中途测试不断增多，特别是跨隔支撑测试具有一定施工风险和难度，要求测试质量不断提高。结合油田生产实际，合理选配了地层测试工具仪表，不断改进测试管串和优化施工设计，经盐22井中途跨隔测试应用，获得成功。     

Mobility management architectures based on joint mobile IP and SIP protocols

In the all-IP wireless networks beyond the third generation, mobility management can be effectively achieved by applying mobile IP (MIP) and the session initiation protocol (SIP) jointly. Nevertheless, an efficient combination of both protocols remains an open research issue. Conventional hybrid MIP-SIP mobility architectures operate MIP and SIP almost independently, resulting in significant redundant costs. This article investigates the representative hybrid MIP-SIP architectures and explores the joint optimizations between MIP and SIP for a more cost-efficient mobility support whilst utilizing their complementary power. Two novel design approaches are presented. The first approach culminates in a tightly integrated architecture, which merges the redundant mobility entities in MIP and SIP to yield maximum system efficiency. The other approach leads to a loosely integrated architecture, where necessary interactions are introduced between MIP and SIP mobility servers while their physical entities are kept intact. Major mobility procedures, including location update, session setup and handoff, are discussed in these architectures. The analytical results demonstrate that both proposed architectures outperform typical hybrid MIP-SIP architectures in terms of clear-cut reduced signaling costs     

不同注F剂量与CMOS运放电路辐照损伤的相关性

在不同注F剂量条件下,对P沟和N沟两种不同差分对输入CMOS运放电路的电离辐照响应进行了研究.分析比较了注F和未注F运放电路电离辐照响应之间的差异.结果表明,在栅场介质注入适量的F,可有效抑制辐照感生的氧化物电荷尤其是界面态的增长,从而提高CMOS运放电路的抗辐照特性.     

小波变换分离太阳射电频谱图中的纤维结构

太阳射电爆发纤维精细结构是太阳射电爆发活动中一类重要的观测现象,利用二维小波变换对纤维精细结构动态频谱图进行处理,分离频谱图中的纤维结构。首先对原始频谱图实行多层小波变换,由低频分量重构原始图像,就可得到爆发的背景信息,令原始频谱图减去背景并经过阈值处理后,便可将原始频谱图中的纤维结构很好地分离出来。     

下一代无线通信概念和技术

下一代无线通信(NextG:Next-generationwireless)的主流是随时随地的无线通信系统和无缝的高质量无线业务。概述了随时随地的无线通信和业务发展情况,并且介绍了为下一代无线通信的发展提供基础的关键技术。     

石膏转化制硫酸钾结晶动力学及结晶添加剂研究

研究了浓氨介质中石膏与氯化钾直接转化制硫酸钾的结晶动力学及结晶添加剂的作用效果。结果表明 ,硫酸钾在氨介质中的成核速率与晶体生长速率、悬浮密度、搅拌速率存在如下关联式 :B0 =5 .64 13×10 8G3.32 0 8Mt0 .0 559np0 .2 92 8。加入异丙醇、OP乳化剂及十二烷基苯磺酸钠等添加剂 ,可使硫酸钾结晶产品纯度提高 ,晶体形态整齐均匀