Considerations in application and selection of unit substationtransformers

This paper discusses secondary unit substations transformers (USTs) ranging from 300 up through 2500 kVA with 34.5-kV maximum primary voltages and with secondary voltages 600 V and below. Pad-mounted (compartmentalized) transformers are not considered in this paper. The first part of this paper discusses USTs belonging to two general categories, liquid type and dry type (nonliquid type). Liquid types include a discussion of the presently available insulating fluids: mineral oil, high-temperature hydrocarbon fluid, silicone fluids, and the new vegetable-based fluids. Dry types include a discussion of vacuum pressure impregnated polyester, vacuum pressure encapsulated silicone, partial cast, and full cast insulation systems. The National Electric Code (1999) requirements as they affect both liquid- and dry-type USTs for both outdoor and indoor locations are considered. The paper discusses the relative advantages of each UST within each category with respect to the following: (1) first cost; (2) operating costs (losses); (3) overload capability; (4) fan cooling; (5) space factor; (6) environmental factors; (7) sound levels; and (8) maintenance     

The Athy—Heckel equation applied to granular agglomerates of basic tricalcium phosphate [3Ca3PO4)2·Ca(OH)2]

It is shown that direct compression grade tricalcium phosphate yields linear Heckel plots only if the particle density used is that obtained by liquid pycnometry or mercury porosimetry. If the true density is used (i.e. that obtained by gas displacement), then linearization is not obtained in a pressure range where bonding evidently occurs. It is shown that the pore volume in the range of diameters from 0.5 to 2 μm decreases as tableting pressure increases, and that bonding is associated with the loss of pores of this size.     

“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

Analog VLSI model of binaural hearing

The stereausis model of biological auditory processing is proposed as a representation that encodes both binaural and spectral information in a unified framework. A working analog VLSI chip that implements this model of early auditory processing in the brain is described. The chip is a 100000-transistor integrated circuit that computes the stereausis representation in real time, using continuous-time analog processing. The chip receives two audio inputs, representing sound entering the two ears, computes the stereausis representation, and generates output signals that can directly drive a color CRT display. Outputs from the chips for a variety of artificial and speech stimuli are shown.     

Half-bridge inverter using 4H-SiC gate turn-off thyristors

This paper reports on the first demonstration of a half-bridge power inverter constructed from silicon carbide gate turn-off thyristors (GTOs) operated in the conventional GTO mode. This circuit was characterized with input bus voltages of up to 600 VDC and 2 A (peak current density of 540 A/cm²) with resistive loads using a pulse-width modulated switching frequency of 2 kHz. We discuss the implications of the thyristor's electrical characteristics and the circuit topology on the overall operation of the half-bridge circuit. This work has determined the conservative critical rate of rise value of the off-state voltage to be 200 V/μs in these devices     

Performance and modeling of advanced Ti:LiNbO3 digitaloptical switches

High-performance Y-branch digital optical switches realized in Ti:LiNbO₃ are presented. Their switching response functions have been optimized in terms of switch voltage and crosstalk ratio. The optimization is based on analyzing different types of waveguide shaping and switching arrangements using coupled mode theory and computer simulations. Excellent switching characteristics are achieved with devices exploiting a specially shaped waveguide branch in a dilated switch arrangement. Demonstrated performances include switching voltage as low as 9 V with crosstalk suppression better than 45 dB and fiber-to-fiber losses as low as 4 dB. Polarization independence with crosstalk suppression better than 40 dB over a 1520- to 1570-nm wavelength range is achieved for any applied switch voltage greater than 18 V. These optimized digital optical switches have further demonstrated the capability to reshape electrical input signals at switching rates of several hundred megahertz