Experimental and theoretical studies on a distributed temperaturesensor based on Brillouin scattering

Results are reported from recent research on the use of the Brillouin gain/loss mechanism for distributed sensing. A theoretical model of the interaction of the pulsed and CW beams is described and compared with experiments. Results from a system with a 51 km sensing length are presented. We finally investigate issues related to the variation within the sensing fiber of the polarizations of the two beams     

Simulation study of peak junction temperature and power limitationof AlGaAs/GaAs HBTs under pulsed and CW operation

The authors have used a 3-D transmission-line matrix (TLM) modeling method to study the junction temperature distribution and power limitation of device geometries with multiple embedded heat sources. Peak values of the junction temperature against the dissipated power density under both pulsed and CW operation are presented for a typical power AlGaAs/GaAs HBT structure. These data should facilitate the rapid determination of junction temperature for a given output power, which is of paramount importance in power device design     

AN improved method of optimization for electrical machines

Methods of optimizing the design of electrical machines are discussed. The augmented Lagrangian multiplier method is described, and an algorithm for this method is introduced. The method is compared with the more familiar exterior penalty function method using, as an example, the cost optimization of permanent magnetic variable-speed drive motors. The improved method is shown to be superior, both in its ability to reach an optimum consistently and in the number of required iterations     

Double-step generation of ellipses

The principle of double-step incremental generation of nonparametric curves on a discrete plane is used to develop a double-step algorithm for scan converting ellipses in sixteen separate segments. The algorithm iterates only half as many times as current algorithms, while each iteration demands the same number of operations or slightly fewer operations than M. Pitteway's (1967, 1985) algorithm (previously the fastest one). This marked gain in the speed of scan conversion is due to the fact that the middle pixel in a two-step increment is obtained without computation     

TEM study of PLZT ceramics

The microscopic structures of PLZT(7.9/70/30 and x/65/35, x = 7 or 8) ceramics were studied by means of transmission electron microscopy. The presence of micro-regions in PLZTs was first verfied.     

Effects of thymectomy and glucocorticoid therapy on peripheral lymphocytes in myasthenia gravis

Clinical manifestations and peripheral blood lymphocyte subset changes were studied in patients with myasthenia gravis (MG) to elucidate the mechanism of clinical improvement following treatment, with thymectomy (Tx) or glucocorticoid (GC) therapy. The changes found were: 1. There was a significant increase in percentages of CD3+, CD29+ CD4+ cells and CD4/CD8 ratio and a significant decrease in percentages of CD8+ and CD16,56+ cells in patients who had never been treated with any immune therapy. 2. After Tx or GC therapy, CD3+ and CD4+, CD29+ cells were decreased, but the number CD19+ and CD16, CD56 cells did not change. 3. Tx had a special effect on CD8+ cells. In most of the patients who showed clinical improvement after Tx, CD8+ cells were increased and CD4/CD8 ratio wad decreased. 4. Anti-acetylcholine receptor (AChRAb) titers were markedly decreased after GC therapy. These results indicate that there were obvious abnormalities in cell-mediated immunity in addition to those in humoral immunity in myasthenia gravis. These abnormalities tended to be normalized after Tx or GC therapy.     

A numerical investigation on the geometry dependence of the crack growth resistance in CT specimens

The influence of the specimen thickness B and the ligament length b on the J _R -curves is numerically investigated for CT specimens. The thickness effect is taken into account with 2-D analyses by dividing a plain sided specimen into a plane stress part and a plane strain part. The fracture process is controlled by experimentally determined critical values of the crack tip opening displacement for crack growth initiation (CTOD_i) and the crack tip opening angle for stable crack growth (CTOA_C). It is shown that for the global behaviour of a plain sided specimen, the B/b ratio is essential. The difference between the geometry dependence of the initiation value of the J-integral and the geometry dependence of the slope of the J _R -curves is also shown.