EFFECT OF ALLOY ELEMENTS ON QUASIEQUILIBRIUM MICROSTRUCTURE IN Fe-Mn-Ni-Cr STEELS

The microstructures of Fe-Mn-Ni-Cr steels with medium carbon and the effect of alloy ele-ments on them have been investigated by means of X-ray diffraction quantitative phase ana-lyses,metallography and hardness tests.The volume fraction of martensite in steels quenchedat 1100℃ can be expressed as:f_M~(1100)=162.643-15.482Mn-7.36Ni-4.286(Cr+Mo+V)Based on this expression,the quasi-equilibrium microstructure diagram has been obtained.Itis shown that the effect of Mn on the austenite stability is greater than that of Ni.The equiva-lent [Ni]=2.104Mn+Ni and equivalent [Cr]=Cr+Mo+V.The driving force for martensite transformation at M_s point has been calculated to hedrastically decreased by element Mn.     

QUASI-EQUILIBRIUM MICROSTRUCTURES AND EFFECT OF ALLOY ELEMENTS IN Fe-Mn-Ni-Cr STEELS

本文利用X射线定量相分析及金相观察和硬度测试,考察了中碳Fe-Mn-Ni-Cr钢的组织及合金元素的作用。建立了经1100℃淬火后的马氏体体积分数与合金成分的定量关系式; f_M~(1100)=162.643-15.482Mn-7.36Ni-4.286(Cr+Mo+V)并在此基础上给出了亚平衡组织图。结果表明,Mn稳定奥氏体的作用大于Ni的作用。Ni和Cr当量分别以[Ni]=2.104Mn+Ni,[Cr]=Cr+Mo+V表示。计算了M_S点处的马氏体相变驱动力,指出Mn具有强烈降低相变驱动力的作用。     

HIGH TEMPERATURE LOW CYCLIC FATIGUE BEHAVIOUR OF DIRECTIONALLY SOLIDIFIED Ni-BASE ALLOY DK3

研究了镍基定向凝固高温合金DK3和普通铸造合金K3在760℃应变控制和应力控制下的高温低周疲劳行为。结果表明:这两种合金的高温低周疲劳行为可以用常规的应力疲劳曲线来表征。DK3合金不存在“过渡疲劳寿命”N_T,K3合金则很低。在各种不同应变或应力水平下,DK3合金的低周疲劳寿命高于K3合金,当应力水平为785至980MPa时,其寿命约差1倍,当应力水平为490至685MPa时,则差2倍多。     

Quantification of trace amounts of impurities in high purity cobalt by high resolution inductively coupled plasma mass spectrometry

An analytical method using high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) for rapid simultaneous determination of 24 elements (Be, Mg, Al, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Ge, As, Se, Mo, Ag, Cd, Sn, Sb, Ba, Pt, Au, and Pb) in high purity cobalt was described. Sample digestions were performed in closed microwave vessels using HNO3 and HCl. The matrix effects because of the presence of excess HCl and Co were evaluated. The usefulness of high mass resolution for overcoming some spectral interference was demonstrated. The optimum conditions for the deter- mination were tested and discussed. The standard addition method was employed for quantitative analysis. The detection limits were 0.016-1.50 μg?g?1, the recovery ratios were 92.2%-111.2%, and the RSD was less than 3.6%. The method was accurate, quick, and convenient. It was applied to the determination of trace impurities in high purity cobalt with satisfactory results.     

贵金属Cu、Ag、Au的电子结构和物理性质

由纯金属单原子理论(OA)确定了面心立方结构(FCC)贵金属Cu、Ag、Au的电子结构依次为[Ar](3dn)5.58(3dc)4.21(4sc)0.23(4sf)0.98、[Kr](4dn)4.87(4dc)4.56(5sc)0.66(5sf)0.91、[Xe](5dn)4.20(5dc)4.90(6sc)1.57(6sf)0.33,并确定了Cu、Ag、Au的密排六方结构(HCP)和体心立方结构(BCC)两种初态特征晶体和初态液体的电子结构。根据自然态的电子结构定性解释了熔点、拉伸强度、维氏硬度、体弹性模量、电导和热导率物理性质差异与电子结构的关系,定量计算了晶格常数、结合能、势能曲线及线热膨胀系数随温度的变化。根据非自然态的电子结构,定性解释了晶体结构BCC和HCP的关系。     

A SIMPLIFIED MODEL FOR NO-STANDARD MICROREGION QUANTITATIVE EDS ANALYSIS OF MULTICOMPONENT ALLOYS

本文对作者建立的微区成分无标样定量分析法进行了简化,使原有的计算量大为减少。 用简化模型对Cu-Si,FeS_2,NaCl,GaAs试样和多元钢样原实验数据进行了定量计算,并与原模型多元程序计算结果进行比较。结果表明,这种简化是合理的。     

Borides at interfacial zone of IC6 TLP bonded joints

1　INTRODUCTIONTransientliquidphase (TLP)bondingtechniquehasbeensuccessfullyusedinjoiningheatresistantal loys ,likeHastelloyX ,Inconel713C ,In10 0 ,Udimet5 0 0 ,70 0 ,MarM 2 0 0 ,0 0 7,2 4 7,30 2 ,Rene′80 ,TD NiCr ,MA75 4,6 0 0 0 ,PWA14 2 2 ,CSMX 2etc ,whicharesusceptibletohotcrackingor post weldheat treatmentcrackingproblemsduringfusionweld ing[14 ] .Inaddition ,therewerereportsofjoiningNiAlandTiAlintermetallicsbyTLPbondingmethod[510 ] .Forexample ,Galehadinvestigatedthemic…     

面向网络化定制的产品族复合建模技术

在分析了网络化定制关键技术的基础上，针对性地对信息映射方法和产品族建进行了研究。提出了多层结构信息映射模型，以及综合类元件和参数化特征建模的双层复合产品族模型。结合本方法和以往网络化制造领域中所取得的成果，实现了较完整的基于Web的个性化定制过程。     

用气冲气推成形触头造型机制造电机壳铸型的试验研究

扼要介绍了用气冲气推成形触头造型机制造电机壳铸型的成型过程及其实砂效果,试验结果表明,在工作气压为0,4￣0.45MPa的条件下,气冲气推成形触头造型机对电机壳类铸型的紧实,实砂效果十分理想,砂型紧实度高而且均匀。