离子液体用于燃料油深度脱硫的研究进展

首先介绍了加氢催化脱硫和其他脱硫技术的特点,综述了近年来国内外利用离子液体在萃取脱硫、萃取脱硫与氧化脱硫耦合、萃取脱硫与生物脱硫耦合等方面的研究。认为离子液体萃取脱硫具有操作简便、可循环使用、无需氢气、环境友好、能深度脱硫等特点,是一项具有广阔发展前景的技术。若要实现该技术的工业化应用,还需进一步加强离子液体在合成工艺、脱硫选择性及回收再生等方面的研究。     

OFDM-MIMO系统及其频率同步分析

多媒体业务对无线通信的带宽与品质提出了更高的要求，OFDM和MIMO由于满足了这一需求被越来越多的无线通信标准采用所为底层的调制和传输技术。频率同步问题是OFDM—MIMO物理层设计中正确解调的前提和基础，本文介绍了OFDM—MIMO的原理、特点和频率同步问题的研究现状。     

基于纠错编码和小波变换的数字图像水印算法

文章提出了一种基于小波变换和纠错编码的数字图像水印算法,该算法不需要利用原始图像。实验结果表明,该算法较好地保持了图像的质量,并大大提高了检测的可靠性,对常见的图像处理方法显示了较强的鲁棒性。     

F-X域粘弹性波动方程保幅偏移

提出了一种利用粘弹性声波波动方程进行偏移的新方法。其基本思路是,修改成像条件,使修改后的成像方程中考虑振幅补偿,然后利用粘弹性、单程波动方程在F-X域对震源和接收点波场进行延拓,进而完成散射、透射等补偿。理论数据处理和实际地震资料处理表明,该方法理论基础可靠,处理效果明显,能较好地解决实际地质问题。     

"信号调制法"研究电子诱导脱附--基本原理及误差分析

电子诱导脱附是近年来在真空科学与表面科学领域内的热门研究课题。它不仅作为研究和探讨原子激发过程以及电子能量传输机制的有效手段,而且已经逐渐成为获取表面和界面结构、状态等信息的有效方法。“信号调制法”是利用脉冲电流能量调制的电子探束取代传统的直流电子探束,并通过测量电子诱导脱附产物引起的压强变化量,来研究电子诱导脱附的新方法。本文系统地介绍了该方法的基本原理,并从理论上对该方法带来的测量误差进行了分析。     

低温等离子体对血管内金属支架的表面改性

生物材料用于人体必须要具备生物相容性。尤其是与血液相接触的材料如血管内支架必须要具备血液相容性。材料的表面特性直接影响血液系统中是否会出现血栓。本文针对金属血管内支架的表面特性、与血液的界面反应以及用于提高血液相容性的低温等离子表面改性进行了简要综述     

Novel algorithms for shared segment protection

The major challenges in designing survivable schemes are how to allocate a minimal amount of spare resources (e.g., bandwidth) using fast (e.g., polynomial-time) algorithms, and, in case a failure occurs, to be able to recover quickly from it. All existing approaches invariably make tradeoffs. We propose novel shared segment protection algorithms which make little or no compromise . We develop an elegant integer linear programming (ILP) model to determine an optimal set of segments to protect a given active path. Although the ILP approach is useful for a medium-size network, it is too time consuming for large networks. Accordingly, we also design a fast heuristic algorithm based on dynamic programming to obtain a near-optimal set of segments. Although the heuristic algorithm has a polynomial time complexity, it can achieve a bandwidth efficiency as high as some best-performing shared path protection schemes and, at the same time, much faster recovery than these shared path protection schemes. The proposed scheme is also applicable to a wide range of networking technologies, including Internet Protocol and wavelength-division multiplexing networks under the generalized multiprotocol label switched framework.     

Achieving fast and bandwidth-efficient shared-path protection

Dynamic provisioning of restorable bandwidth guaranteed paths is a challenge in the design of broad-band transport networks, especially next-generation optical networks. A common approach is called (failure-independent) path protection, whereby for every mission-critical active path to be established, a link (or node) disjoint backup path (BP) is also established. To optimize network resource utilization, shared path protection should be adopted, which often allows a new BP to share the bandwidth allocated to some existing BPs. However, it usually leads the backup paths to use too many links, with zero cost in term of additional backup bandwidth, along its route. It will violate the restoration time guarantee. In this paper, we propose novel integer linear programming (ILP) formulations by introducing two parameters (/spl epsi/ and /spl mu/) in both the sharing with complete information (SCI) scheme and the distributed partial information management (DPIM) scheme. Our results show that the proposed ILP formulations can not only improve the network resource utilization effectively, but also keep the BPs as short as possible.     

鱼雷罐喷粉预处理过程水模研究

在鱼罐喷粉预处理水模实验数据的基础上，进一步利用线性回归确定各工艺操作参数对喷吹基本参数（均混时间、粉剂穿透比和粉剂停留时间）的影响，得出各传输动力学基本参数的函数关系式。     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.