Feasibility study of large-scale mass customization 3D printing framework system with a case study on Nanjing Happy Valley East Gate

At present, the development and implementation of digital transformation are the keys to promoting high-quality industry development. The new digital fabrication method of robotic 3D printing is a research area being studied by many to tackle the issue of the declining productivity of traditional construction methods. Although many studies have been done, most of the current 3D printing projects are facing limitations in terms of scale. In order to bridge the gap, this article proposed a mass customization 3D printing framework system for large-scale projects. This article discusses how mass customization is made possible through the joint operation of the FUROBOT software and 3D printing hardware. By taking the east gate of Nanjing Happy Valley Plaza as a case study, the article demonstrates and studies the feasibility of the large-scale mass customization 3D printing framework system.     

Decreased CD10-positive granulocytes for the differential diagnosis of myelodysplastic syndrome

Myelodysplastic syndromes (MDS) are highly heterogeneous myeloid neoplasms, and a large number of patients are difficult to diagnose and classify by blood and bone marrow examination. As a surface marker of granulocyte, studies have shown CD10 can be used to define the degree of granulocyte maturation in MDS patients. However, whether it can be used for differential diagnosis of MDS and other hematological diseases remains inconclusive. To explore the value of CD10 for differential diagnosis of MDS, 60 newly diagnosed MDS, 20 aplastic anemia (AA) patients, and 35 iron-deficient anemia (IDA) patients were selected for this study. Bone marrow (BM) specimens were processed for surface marker analysis and labeled with pre-conjugated monoclonal antibodies. Stained cells were detected by flow cytometry. Our results indicated that CD10-positive granulocytes were significantly decreased in BM of MDS patients than AA and IDA patients, and the level of CD10-positive mature granulocytes was not associated with the clinical stages of malignancy. Receiver operating characteristic (ROC) areas under the curve (AUC) of CD10-positive granulocytes was 0.86 and 0.85, respectively, in MDS patients than the IDA group and AA group with good specificity and sensitivity. Further, CD10-positive granulocytes were increased after effective treatment. In conclusion, we found the decrease in CD10-positive granulocytes has a differential diagnostic value of MDS.     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。     

一种5 重real-time PCR筛查转基因水稻方法的建立

以转基因水稻中最常用的CaMV35S启动子、NOS终止子、Cry1Ab/Ac基因、HPT基因及SPS水稻内标基因为研究对象，利用5 种不同的荧光信号（FAM、HEX、Taxas Red、Cy5、Cy5.5）进行多重实时聚合酶链式反应（real-time polymerase chain reaction，real-time PCR）检测方法的研究。通过引物组合筛选、反应体系优化、特异性测试、灵敏度测试、适用性测试等一系列实验，建立了5 重real-time PCR方法，灵敏度可达0.032%。此方法具有灵敏度高、结果准确、通量大等优点，可实现水稻中转基因成分的快速、高效检测。     

氮化硅/石墨激光合金化涂层的组织结构与性能研究

为获得金属表面特别是高副接触金属表面含自润滑特性且具有高硬度耐磨特性的功能材料 ,研究了 45 # 钢表面激光合金化氮化硅 /石墨复合涂层的工艺方法、组织特征、界面形态及其形成机制 ,利用光学显微镜、扫描电镜和X射线能谱对所形成合金化层的元素分布和含量进行了分析 ,并对试样硬度进行了测定。结果表明 ,合金化层中元素Fe ,Co ,Si,C分布均匀 ;C含量达到了 15 6 9%,大部分以石墨的形式存在 ,具有一定的自润滑性能 ;但在形成合金化层的温度条件下 ,氮化硅分解严重 ;合金化层硬度提高的主要原因是Si Fe ,Co Fe固溶体的强化作用及高碳马氏体的生成和高硬度碳化物的存在。     

CMOS光接收机主放大器设计

利用CMOS工艺设计一种用于SDH STM 4速率级(622 Mb/s)光纤用户网的光接收机放大电路。此电路由输入/输出缓冲、主放大单元、偏置补偿电路4部分组成。通过直接耦合技术提高增益,降低功耗;利用有源电感负载提高系统带宽。采用商用SmartSpice电路仿真软件和CSMC HJ 0.6μm工艺参数对该电路进行仿真。结果表明,该电路在5 V工作电压下中频增益为81 dB,3 dB带宽为470 MHz。     

基于ARM微处理器的故障记录系统

给出了在普通数据采集基础上的故障记录系统的设计方案,利用ARM微处理器实现了模拟信号较完整的故障波形记录和开关信号的事件顺序记录(SOE)。对LPC2106ARM系列处理器、ADS7871模/数转换器以及数据通信接口等内容进行了讨论,阐述了系统的工作原理、软件处理方式、系统通信。该设计方案电路简单,特别适用于电力系统。     

A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process