软土地区盾构施工沉降界限

结合杭州地铁二号线实测沉降,采用“vi速度法”及“拟合直线法”分析不排水瞬时沉降与排水固结沉降的时间界限.分析发现,在地表无隆起的情况下,可以将地表变形分成3个阶段,其中瞬时沉降及固结沉降可以分别拟合为斜率不同的直线,前者斜率大于后者.在盾构脱开管片8.5～9 d后,地层进入排水固结阶段. 在同步注浆导致地表隆起的情况下,地层受到二次扰动,可以将地表变形分为5个阶段,在盾尾脱开管片10.5～12 d后,地层进入排水固结阶段．     

天然帽用草纤维的形态结构及EDS能谱分析

对蓆草、棕丝草、琅琊草、咸草、蒲草等5种帽用草纤维用扫描电镜观察其表面形态和截面结构,发现帽用纤维表面存在大量的气孔和沟槽,测量出气孔的长度20-73μm,宽度8-33μm。截面有较大的空隙,纤维空隙的大小依次是棕丝草、蒲草、琅琊草、蓆草、咸草。对其表面选取微区进行EDS能谱分析,结果表明5种帽用草纤维都含有C、O、Al,且C、O元素的含量都在96.99%以上,其他如Si、Na、Mg、Cl、P等属于微量元素,属纤维素纤维。     

高强度热成形钢板冷却速率-强度-硬度预测

基于高强度钢板热成形平板模具分区冷却试验获得了淬火过程阶段冷却速度对机械强度-硬度的影响规律。采用量纲分析法建立了热成形材料冷却速率-机械强度-硬度指数模型,并验证了该模型的有效性。通过编制用户子程序将该模型引入自主开发的KMAS_HF软件平台中,实现了对典型U形热成形产品淬火后强度硬度的数值仿真预测。结果表明:该模型对热成形高强度钢淬火后机械性能仿真预测具有较好的适用性,为实现梯度硬度复合热成形工艺优化及产品性能分析提供了一种新的仿真分析流程。     

Preparation and characterization of high strength and high modulus PVA fiber via dry-wet spinning with cross-linking of boric acid

To improve the mechanical properties of polyvinyl alcohol (PVA) fibers, a series of PVA fibers were prepared via dry-wet spinning with cross-linking of boric acid (BA) (PVA/BA fibers), and using the mixed solvent of dimethyl sulfoxide and water. Moreover, the final PVA/BA fibers were characterized by Fourier transform infrared spectra (FTIR), scanning electron microscopy (SEM), differential scanning calorimetery (DSC), thermogravimetric analyzer (TGA), powder X-ray diffraction (XRD) and yarn strength tester. Furthermore, with the increasing of BA content, FTIR analysis showed that the degree of crosslinking of BA with PVA increased. SEM images of final PVA/BA fibers presented smooth surfaces, and the diameters decreased firstly and then increased. DSC, TGA, and XRD analysis indicated that the melting temperatures, thermal properties and crystallinities first increased and then decreased with the increasing of BA content. In addition, mechanical properties measurements illustrated that the cross-linking existed at an optimal BA content of 0.3 wt%, and PVA/BA-0.3 fiber had the highest tensile strength and Young's modulus of 13.1 ± 0.4 and 360.2 ± 10.4 cN/dtex, respectively.     

分段长初级双边直线感应电动机建模分析

分段长初级双边直线感应电动机(LP-DSLIM)系统由若干段单元电机串联或并联组成,为准确描述次级运动过程中单元电机的推力等状态变化和过分段时的暂态过程,该文提出了一种新型单元电机数学模型及分段LP-DSLIM系统模型.首先,对分段LP-DSLIM系统的特点进行分析,通过引入虚拟次级板将每段单元电机耦合的次级延长至与初级等长,以使单元电机初级、次级之间始终保持全耦合;然后,结合耦合因数得到实际次级磁链和初级磁链,以此推导得到新型单元电机数学模型,并基于此建立串联供电和并联供电的分段LP-DSLIM系统模型;最后,有限元计算和实验结果验证了提出的新型单元电机数学模型和分段LP-DSLIM系统模型的正确性.     

Research progress on preparation of biomass-derived porous carbon and its adsorption of pharmaceuticals in wastewater

The rapid development of urban modernization and industrialization has caused increasingly serious pollution to the environment, especially water contamination. In recent years, the content of pharmaceuticals in industrial wastewater has increased year by year, and the pollution should not be ignored any more. Therefore, the development of new porous materials for the adsorption and separation of pharmaceutical molecules in wastewater has become a current research hotspot. This article summarizes the recent research on the adsorption and separation of pollutants in wastewater by biomass-derived porous carbons (biochars). First, it briefly introduces the treatment methods of pollutants in wastewater, and mainly focuses on the preparation and modification of biochars. Combined with the surface chemical properties and pore structure of the carbon materials, this paper summarizes and prospects the adsorption properties of biochar to pharmaceuticals.     

基于体效应的SiC MOSFET器件栅极老化监测方法研究

长期以来,栅极老化一直是SiC MOSFET器件可靠性研究的关键,而偏置温度不稳定性则是栅极老化的重要现象。由于栅极老化的偏置温度不稳定性存在应力撤出后的恢复现象,如能在可靠性实验中快速、准确地监测SiC MOSFET器件的栅极老化变化量,对可靠性研究具有重要意义。因此,文中提出一种新的栅极老化监测方法。该方法以体效应下的阈值电压VTH(body)为基础,建立理论模型来描述VTH(body)和栅极老化之间的关系。提出在栅极电压开关过程中从体二极管电压–栅极电压曲线中得到VTH(body)的方法,并详细研究实验参数对VTH(body)的影响。此外,通过高温栅偏实验对VTH(body)的实用价值进行验证,并与栅极老化参数阈值电压VTH进行对比。实验结果证明,提出的新型栅极老化监测方法可以实现栅极老化的快速、准确及非恒温环境监测。     

Phase Transformations in Low-Fe Alloys of the Al-Cu-Fe System

Microstructure and phase transformation in the Al-Cu-Fe alloys of the approximate compositional range of 20-50 at.% Cu and 2 - 10 Fe at.% have been investigated from samples quenched from their respective temperatures by means of different thermal analysis, magnetothermal analysis, scanning electron microscopy, electron probe analysis and powder X-ray diffraction. Representative phase transformations categorized as polymorphic, discontinuous precipitation,quasi-binary eutectoid, and ternary transitional U-type phase transformation are presented. These phase transformations were found to have a common feature which consumes the β phase and appears the φ phase. A schematic diagram was proposed to demonstrate the transition processes with decreasing temperature.     

Morphology, structure and formation mechanism of silicide coating by pack cementation process

The MoSi2 coating on C 103 niobium based alloy was prepared by pack cementation method. The formative mechanism, morphology and structure of coating were investigated. The silicide coating was formed by reactive diffusion obeying parabolic rule during pack cementation process. It is found that the composite structural coating is composed of three inferior layers as follows. The main layer is composed of MoSi2, the two phases＇ transitional layer consists of NbSi2 and a few NbsSi3 and the diffuse layer is composed of NbsSi3. The dense amorphous glass layer formed on the surface at high temperature oxidation circumstance can effectively prevent the diffusion of oxygen into coating.     

基于参数化特征建模的汽车转向器CAD系统的研制

通过对汽车转向器结构特点进行分析，得出了汽车转向器CAD策略，利用UG软件平台并结合UG／OpenGRIP语言来创建参数直接驱动的转向器三维参数化CAD建模程序，开发了一种基于参数化特征建模的汽车转向器CAD系统。经实际应用表明，该系统设计效率高，实用性强，大大缩短了产品开发周期。