Fundamental Behavior of Direct-Coupled Submicrosecond Pulse Energization in Electrostatic Precipitators

The fundamental characteristics of the direct-coupled pulse energization in electrostatic precipitators (EP's) are investigated in a test rig comprised of a coal pulverizing facility, a furnace, a gas cooling system, and an EP. The EP consisted of a corona electrode with barbed wires and a collection electrode with 300-mm duct spacing. This simulates the type of EP normally used in a coal-fired power station. The pulse-energized collection field shows a very high collection performance of more than 99 percent collection efficiency and the performance enhancement compared to the conventional dc energization, causing very severe back corona, becomes as large as H = 2.50.H is the enhancement factor in terms of the Deutsch migration velocity in the case of the very high resistivity dust of rd = 2 x 1013 ?cm at the gas temperature of Tg = 150°C. Even at the lower level of the dust resistivity at Tg = 110°C, where no back corona occurs in the dc-energized collection field, the performance enhancement is as large as H = 1.21. The mechanism of such great performance enhancement is likely to be the result of the very uniform and very intense formation of corona plasmas on the wires as a result of the very fast rise in the pulse voltage applied and a special sawtooth waveform of the operating voltage between the corona and collection electrodes.     

Breaking Ability and Interrupting Phenomena of a Circuit Breaker Equipped with a Parallel Resistor or Capacitor

This paper discusses the breaking ability of an air blast circuit breaker (ABB) or SF6 gas circuit breaker (GCB), and the interrupting phenomena around current zero in the case where a resistor or capacitor is connected in parallel with its interrupter to improve the breaking ability. It has been clarified that the use of a parallel resistor for ABB, and that of a parallel capacitor for GCB are the most effective methods to improve the breaking abilities; the parallel resistor not only serves to reduce the rate of rise of the transient recovery voltage (rrrV), but also shifts the current from the interrupter to itself around the current zero, thus reducing the stress for interruption. The improvement of the breaking ability is achieved by reducing the initial average rrrV between zero and 1 microseconds (inherent value), when the parallel capacitor is used with the GCB.     

A spherical aberration-corrected 200 kV TEM

A spherical aberration (Cs)-corrected 200 kV TEM was newly developed. The column of the microscope was extended by 25 cm and the inner yoke of the objective lens was modified to insert some parts of the corrector elements. The corrector has two hexapole elements that play a main role in Cs correction and they are placed at a position equivalent to the coma-free point of the objective lens by using two transfer doublet lenses. The Cs correction was successfully carried out by means of the third-order aberration that was generated in the two extended hexapoles. The Cs can be corrected to the desired value and also can be overcompensated in order to produce a negative Cs, as with the corrected Cs of -23 microm shown in this work. The optical system of the corrector does not produce second- and fourth-order aberrations, and can correct residual aberrations up to the third order. All of the corrector elements are computer-controlled and the third-order aberrations are quite stable after they are properly corrected. The resolution of 0.135 nm was experimentally confirmed by the Young's fringe method. Image simulations of a silicon [110] single crystal were made with various Cs and defocus values to demonstrate the effectiveness of arbitral control of Cs.     

Resistance to wear and cavitation erosion of bearing alloys

Sliding wear and vibratory cavitation erosion tests in paraffin oil were carried out on bearing alloys, i.e. tin-based and lead-based white metals, Cu-Pb alloy and leaded bronze. In lubricated wear under mild conditions the surface is worn smooth and a slight difference exists between the wear resistances of the four alloys. In cavitation erosion an eroded surface which is much rougher than the worn surface is formed. Cavitation erosion is affected strongly by the composition and crystal structure of the alloy and thus the erosion resistances of the four alloys differ greatly, the ranking of resistance being lead-based white metal < Cu-Pb alloy < tin-based white metal < leaded bronze. The surface damage, which is caused by the joint action of cavitation erosion and wear, was also investigated by rubbing the eroded surfaces which had been exposed to cavitation erosion for various times. This damage becomes larger with increasing cavitation damage. The resistance to this damage differs much more in the four alloys tested and tends to correlate with the results of the erosion tests rather than those of the wear tests. Therefore, it is clear that the cavitation erosion resistance should be considered in the selection of bearing materials.     

Development of a numerical cancellous bone model for finite-difference time-domain simulations of ultrasound propagation

The trabecular frame in cancellous bone has numerous porous spaces of various sizes and shapes. Their continual arrangement changes with position in the bone. Assuming that the complicated pore space is the aggregation of spherical pores, in this study, the trabecular structure was analyzed using a three-dimensional (3-D) X-ray microcomputed tomography (muCT) image. Analysis involved a 3-D cancellous bone model developed for numerical simulations of ultrasound propagation. In this model, the trabecular structure was simplified by regularly arranging spherical pores in a solid bone. Using a viscoelastic, finite-difference, time-domain (FDTD) method with the simplified cancellous bone model, ultrasound pulse waveforms propagating through cancellous bone were simulated in two cases of the propagations parallel and perpendicular to the main trabecular orientation. The porosity dependences of the propagation properties, attenuation, and propagation speed were derived from the simulated waveforms. Comparisons with simulated results using the realistic cancellous bone model reconstructed from a 3-D muCT image, assisted to further validate this simplified model.     

Bioconversion of n−3 and n−6 PUFA by <Emphasis Type="Italic">Clavibacter</Emphasis> sp. ALA2

Clavibacter sp. ALA2 oxidized n−3 and n−6 PUFA into a variety of oxylipins. Structures of products converted from EPA and DHA were determined as 15,18-dihydroxy-14,17-epoxy-5(Z),8(Z),11(Z)-eicosatrienoic acid and 17,20-dihydroxy-16,19-epoxy-4(Z),7(Z),10(Z),13(Z)-docosatetraenoic acid by GC-MS and NMR analyses. In contrast, γ-linolenic acid and arachidonic acid were converted to diepoxy bicyclic FA, tetrahydrofuranyl monohydroxy FA, and trihydroxy FA. Thus, the structures of bioconversion products were different between n−3 and n−6 PUFA. Furthermore, strain ALA2 placed hydroxy groups and cyclic structures at the same position from the ω-terminal despite the number of carbons in the chain and the double bonds in the PUFA.     

Water activity-adjusted enzymatic partial hydrolysis of phospholipids to concentrate polyunsaturated fatty acids

Selective partial hydrolyses of egg yolk phospholipid and squid skin phospholipid were carried out. By keeping the water activity (a _w) of Lipozyme IM at an intermediate level, it was easy to concentrate docosahexaenoic acid (DHA). It was also possible to concentrate both DHA and arachidonic acid (AA) simultaneously to a certain level under this a _w range. However, it was impossible to concentrate AA alone when DHA was present. Though there is a limitation in concentrating AA exclusively, the proposed a _w-adjusted hydrolytic reaction is a promising way for preparing phospholipids rich in DHA.     

Microfluidic device with chemical gradient for single-cell cytotoxicity assays

Here, we report the fabrication of a chemical gradient microfluidic device for single-cell cytotoxicity assays. This device consists of a microfluidic chemical gradient generator and a microcavity array that enables entrapment of cells with high efficiency at 88 ± 6% of the loaded cells. A 2-fold logarithmic chemical gradient generator that is capable of generating a serial 2-fold gradient was designed and then integrated with the microcavity array. High density single-cell entrapment was demonstrated in the device without cell damage, which was performed in 30 s. Finally, we validated the feasibility of this device to perform cytotoxicity assays by exposing cells to potassium cyanide (0-100 μM KCN). The device captured images of 4000 single cells affected by 6 concentrations of KCN and determined cell viability by counting the effected cells. Image scanning of the microcavity array was completed within 10 min using a 10× objective lens and a motorized stage. Aligning cells on the microcavity array eases cell counting, observation, imaging, and evaluation of singular cells. Thus, this platform was able to determine the cytotoxicity of chemicals at a single-cell level, as well as trace the cytotoxicity over time. This device and method will be useful for cytotoxicity analysis and basic biomedical research.     

Electron microscopy at a sub-50 pm resolution

An aberration-corrected electron microscope developed in CREST project has been applied for imaging atoms and clusters buried inside crystals. The resolution of the microscope in scanning transmission electron microscopy (STEM) has experimentally proved to be better than 47 pm by use of a cold-field emission gun at 300 kV. The high resolution has given an advantage for imaging light elements such as lithium atoms discriminating one by one. Moreover, a three-dimensional structure imaging has been demonstrated for dopant clusters by a sub-50 pm STEM, using its high depth resolution.