Effect of polymer density on polyethylene hollow fiber membrane formation via thermally induced phase separation

Microporous high‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) hollow fiber membranes were prepared from polyethylene–diisodecyl phthalate solution via thermally induced phase separation. Effect of the polyethylene density on the membrane structure and performance was investigated. The HDPE membrane showed about five times higher water permeability than the LDPE membrane because it had the larger pore and the higher porosity at the outer membrane surface. The formation of the larger pore was owing to both the initial larger structure formed by spinodal decomposition and the suppression of the diluent evaporation from the outer membrane surface due to the higher solution viscosity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 471–474, 2004     

Analysis of the current distortion factor of a three‐phase,three‐wire system

In a balanced three‐phase system, the three‐phase current distortion factor of three‐phase ac power sources has been expressed by applying the conventional single‐phase current distortion factor, which is defined for a single‐phase system. However, in an unbalanced three‐phase system, it is difficult to express the three‐phase current distortion factor for distorted three‐phase ac currents by means of the conventional single‐phase current distortion factor. For instance, the conventional current distortion factors for three‐phase ac currents are usually different from each other in the unbalanced three‐phase system. To solve the above problem, this paper proposes a novel definition of the three‐phase current distortion factor. The proposed three‐phase current distortion factor is quite effective for the unbalanced three‐phase system as well as the balanced three‐phase system. © 2000 Scripta Technica, Electr Eng Jpn, 131(4): 1–10, 2000     

Development of a Simplified Calculation Tool for Voltage Drop Caused by Transformer Inrush in Distribution System

It is well known that a voltage drop due to inrush current at an energizing transformer may at times interrupt electrical equipment. Generally, the voltage drop is calculated by using a sophisticated tool such as EMTP, so that the transformer saturation phenomenon has been properly represented. However, it is not practical for distribution system engineers to calculate the voltage drop with transformer inrush by using EMTP, because there are many network access requests needing such calculations with many kinds of transformers. Therefore, in this paper, a simplified and easy‐to‐use calculation tool for voltage drops caused by transformer inrush in a distribution system is developed. In order to understand the voltage drop by inrush current during the planning stage, it is formulated by considering the transformer saturation/unsaturation periods in each winding type. The newly developed tool is based on versatile spreadsheet software such as Microsoft Excel ýO.R. It can be used with accuracy similar to that of EMTP. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 185(1): 36–47, 2013; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22394     

Multiple fuzzy state-value functions for human evaluation through interactive trajectory planning of a partner robot

The purpose of this study is to develop partner robots that can obtain and accumulate human-friendly behaviors. To achieve this purpose, the entire architecture of the robot is designed, based on a concept of structured learning which emphasizes the importance of interactive learning of several modules through interaction with its environment. This paper deals with a trajectory planning method for generating hand-to-hand behaviors of a partner robot by using multiple fuzzy state-value functions, a self-organizing map, and an interactive genetic algorithm. A trajectory for the behavior is generated by an interactive genetic algorithm using human evaluation. In order to reduce human load, human evaluation is estimated by using the fuzzy state-value function. Furthermore, to cope with various situations, a self-organizing map is used for clustering a given task dependent on a human hand position. And then, a fuzzy state-value function is assigned to each output unit of the self-organizing map. The robot can easily obtain and accumulate human-friendly trajectories using a fuzzy state-value function and a knowledge database corresponding to the unit selected in the self-organizing map. Finally, multiple fuzzy state-value functions can estimate a human evaluation model for the hand-to-hand behaviors. Several experimental results show the effectiveness of the proposed method.     

Reduction of system matrices of planar beam in ANCF by component mode synthesis method

A method of reducing the system matrices of a planar flexible beam described by an absolute nodal coordinate formulation (ANCF) is presented. In this method, we focus that the bending stiffness matrix expressed by adopting a continuum mechanics approach to the ANCF beam element is constant when the axial strain is not very large. This feature allows to apply the Craig–Bampton method to the equation of motion that is composed of the independent coordinates when the constraint forces are eliminated. Four numerical examples that compare the proposed method and the conventional ANCF are demonstrated to verify the performance and accuracy of the proposed method. From these examples, it is verified that the proposed method can describe the large deformation effects such as dynamic stiffening due to the centrifugal force, as well as the conventional ANCF does. The use of this method also reduces the computing time, while maintaining an acceptable degree of accuracy for the expression characteristics of the conventional ANCF when the modal truncation number is adequately employed. This reduction in CPU time particularly pronounced in the case of a large element number and small modal truncation number; the reduction can be verified not only in the case of small deformation but also in the case of a fair bit large deformation.     

Micromachining of electroformed nickel mold using thick photoresist microstructure for imprint technology

In order to fabricate polymer-based microstructures with feature sizes on the order of micrometers, we have been developing a microimprint technology with a fine nickel (Ni) mold instead of a conventional photolithography technique. The Ni mold was successfully fabricated by electroforming using a positive thick photoresist microstructure patterned on a silicon substrate as a replication master. The photoresist microstructure with excellent edge quality can be obtained under irradiation with single wavelength (g line) selected from a high-pressure mercury lamp. In addition, its sidewall angle in the range of 65° to 84° can be controlled precisely by varying the distance between a photomask and a photoresist surface. On the structured photoresist master, Ni was electroplated up to a thickness of about 110 μm, and then removed from the master. In this process, two-step electroplating at different current densities was carried out in order to prevent deformation of the photoresist master due to stress generated in a Ni electrodeposit. With the Ni mold, fine patterns with a width of 10 or 30 μm and a depth of 24 μm were almost completely transferred to polymetric materials (PMMA). The geometrical dimensions of the fabricated PMMA microstructures were found to be only about 10% reduction against the Ni mold.     

Survey of actual viewing conditions at home and appropriate luminance of LCD‐TV screens

Abstract— To understand actual viewing conditions at home is important for TV design. And the preferred luminance level of LCD TVs under actual viewing conditions is also important in order to obtain both good picture quality and low power consumption. The actual viewing conditions of households and the preferred luminance levels was investigated. In a field test of 83 households, the display luminance, screen illuminance, and viewing locations were measured on site. In laboratory experiments, young and elderly subjects adjusted the luminance of an LCD‐TV screen to their preferred levels under different screen illuminance levels, angular screen sizes, and average luminance levels (ALL) of the images. As a result, two equations, which represent the preferred luminance level of LCD‐TV screens corresponding to different viewing conditions for young and elderly subjects were obtained. When the ALL of the images was 25% and the screen illuminance and angular screen size were set at 100 lx and 20°, respectively, the preferred luminance was 1 60 cd/m² for the young subjects and 248 cd/m² for the elderly subjects. By using the setting of the preferred luminance of an LCD TV under actual viewing conditions, it is possible to conserve energy consumption.     

Development of flexible displays using back‐channel‐etched In–Sn–Zn–O thin‐film transistors and air‐stable inverted organic light‐emitting diodes

We developed flexible displays using back‐channel‐etched In–Sn–Zn–O (ITZO) thin‐film transistors (TFTs) and air‐stable inverted organic light‐emitting diodes (iOLEDs). The TFTs fabricated on a polyimide film exhibited high mobility (32.9 cm²/Vs) and stability by utilization of a solution‐processed organic passivation layer. ITZO was also used as an electron injection layer (EIL) in the iOLEDs instead of conventional air‐sensitive materials. The iOLED with ITZO as an EIL exhibited higher efficiency and a lower driving voltage than that of conventional iOLEDs. Our approach of the simultaneous formation of ITZO film as both of a channel layer in TFTs and of an EIL in iOLEDs offers simple fabrication process.     

Density and viscosity of linear perfluoropolyethers under high pressures

New experimental data on the density and viscosity of linear, unbranched perfluoropolyethers are presented at temperatures from 273 to 333 K and pressures up to 180 MPa. The measurements were carried out by a high-pressure burrette apparatus and a falling-cylinder viscometer. The uncertainties of the measurements are estimated to be less than 0.09% for the specific volume and 2.5% for the viscosity. The P-V data at each temperature are correlated satisfactorily by the Tait equation. The viscosity data are also analyzed and correlated with pressure or molar volume by several empirical and theoretical equations.