Estimation method of frequency bias using normal operating data

A technique of calculating the frequency bias of an electric power system from frequency fluctuation data and total output power is described. An evaluation method for testing the calculations by the new method is developed. The results are in good agreement with estimates based on generator speed regulation but the method gives an excessively high figure for the load frequency bias.     

New approach to the frequency response analysis of an InGaAsavalanche photodiode

The frequency response of an avalanche photodiode has been calculated by solving the transport equations, taking the electric field profile into account. The relationship between the carrier concentration (Nb) in the multiplication layer and the frequency response has been obtained for the first time. This calculation has been carried out for a conventional In_0.53Ga_0.47As avalanche photodiode. The results explain well present experimental data. The saturation velocity of holes in InP is estimated to be 2×10⁶ cm/s. The upper limitation of the gain-bandwidth product is estimated to be 140 GHz at Nb=2×10¹⁷ cm^-3      

Stereospecific anionic polymerization and copolymerization of 1,1-diphenylethyl methacrylate

1,1-Diphenylethyl methacrylate (DPEMA), which is a new methacrylic ester, was synthesized and polymerized by n-butyllithium (n-BuLi) in toluene and THF. The triad tacticity of the polymers was determined from the n.m.r. spectrum of poly(methyl methacrylate) (PMMA) which was derived from them. A highly stereoregular polymer was not formed either in toluene or in THF by n-BuLi between ?78° and 30°C. In toluene, the tacticity depended very much on the polymerization temperature, and unexpectedly, the polymer obtained at ?78°C was rich in syndiotacticity. The polymers obtained in THF were atactic regardless of the temperature. A highly isotactic polymer was formed with Grignard reagents. DPEMA (M₁) was also copolymerized with methyl methacrylate (MMA), diphenylmethyl methacrylate (DPMMA), and trityl methacrylate (TrMA) (M₂) in toluene and THF with n-BuLi; the tacticity of the copolymers was determined. Generally, the stereoregularity of the copolymers was lower than those of the M₂ homopolymers. In the copolymerization with MMA monomer reactivity ratios were also determined.     

Native state kinetic stabilization as a strategy to ameliorate protein misfolding diseases: a focus on the transthyretin amyloidoses

Small molecule-mediated protein stabilization inside or outside of the cell is a promising strategy to treat protein misfolding/misassembly diseases. Herein we focus on the transthyretin (TTR) amyloidoses and demonstrate that preferential ligand binding to and stabilization of the native state over the dissociative transition state raises the kinetic barrier of dissociation (rate-limiting for amyloidogenesis), slowing and in many cases preventing TTR amyloid fibril formation. Since T119M-TTR subunit incorporation into tetramers otherwise composed of disease-associated subunits also imparts kinetic stability on the tetramer and ameliorates amyloidosis in humans, it is likely that small molecule-mediated native state kinetic stabilization will also alleviate TTR amyloidoses.     

New structures of GaAlAs lateral-injection laser for low-threshold and single-mode operation

Two new structures of lateral-injection transverse junction stripe (TJS) lasers, in which the stripe geometry is formed by the double heterojunctions, have been developed. These lasers, the homojunction type and the single-heterojunction type, have a self-reverse-biased p-n junction for concentrating current into the narrow active region. The temperature dependence of the threshold current has been very much improved in one of the new structures, the homojunction type, and is fair compared with those of good conventional broad-contact lasers. The threshold current does not increase rapidly up to 350 K in the homojunction lasers. These lasers exhibit improved characteristics of low threshold, the single longitudinal mode oscillation as well as the single fundamental transverse-mode oscillation, and "kink-free" behavior in the current depedence of the light-output power.     

Study of the stress corrosion cracking of GFRP: effect of the toughness of the matrix resin on the fatigue damage and stress corrosion cracking of GFRP

The stress corrosion cracking of glass fibre-reinforced plastic (GFRP) accompanies a phenomenon of catastrophic failure as a result of the rapid fall in strength owing to corrosion breaking of the glass fibres. This produces a flat surface without pulling fibres out of the plane. Attack on the glass fibres can only occur by contact with an acid which must first diffuse into the matrix resin. It is confirmed, however, that no diffusion occurs or that it is too slow to be detected. The relationship between fatigue damage and stress corrosion in an acidic environment, has been investigated, focusing on the effect of matrix toughness on the resistance to stress corrosion failure of GFRP. Three types of GFRP, made from matrices with different toughness, were studied after subjecting them to fatigue damage at different levels.     

Simultaneous estimation of the thermophysical properties of three kinds of fruit juices based on the measured result by a transient heat flow probe method

The thermophysical properties of three kinds of fruit juices (grape juice, orange juice, and pineapple juice) were measured at various temperatures (10–50 °C) and concentrations (10–50%). A new method for the simultaneous determination of thermophysical properties using a modified version of current probe theory method was proposed. The temperature changes of the probe upon insertion in the sample were fitted to an approximate solution of the heat conduction equation, and the values of two parameters in that solution were determined. Using the values of these parameters, the thermal conductivity and thermal diffusivity of each sample were determined. The specific heat of each sample was estimated from the definition of thermal diffusivity. These thermophysical properties were expressed as a function of concentration and temperature.     

Production of Carbon Nanotube by Ethylene Decomposition over Silica-Coated Metal Catalysts

Formation of carbon nanofibers (CNFs) and carbon nanotubes (CNTs) through the decomposition of ethylene at 973 K was achieved using various metal catalysts covered with silica layers. CNFs of various diameters were formed by ethylene decomposition over a Co metal catalyst supported on the outer surface of the silica. In contrast, silica-coated Co catalysts formed CNTs with uniform diameters by ethylene decomposition. Silica-coated Ni/SiO₂ and Pt/carbon black also formed CNTs with uniform diameters, while CNFs and CNTs with various diameters were formed over Ni/SiO₂ and Pt/carbon black without a silica coating. These results indicate that silica layers that envelop metal particles prevent sintering of the metal particles during ethylene decomposition. This results in the preferential formation of CNTs with a uniform diameter.     

Ceramic molds suitable for rapid forming of CFRP composites via microwave irradiation

Carbon fiber reinforced plastic (CFRP) composites have been considered quite eminent structural materials. For more extensive applications, however, more rapid forming methods of the CFRP composites are required. As for CFRP composites with thermoplastic matrices, microwave heating and pressing with ceramic molds should be promising. In the present work, zirconia molds with varied thermal conductivity were employed to give a desired shape to the CFRP composites heated with microwave irradiation. Experimental results showed that use of the zirconia molds with smaller thermal conductivity results in shorter necessary time for the forming process. Mechanism of the notable change in the heating efficiency is discussed as well.