Melting of a vertical ice cylinder inside a rotating cylindrical cavity filled with binary aqueous solution

The melting of a vertical ice cylinder into a homogeneous calcium chloride aqueous solution inside a rotating cylindrical cavity with several rotating speeds is considered experimentally. The melting mass and temperature are measured on four initial conditions of the solution and four rotating speeds of the cavity. The temperature of the liquid layer becomes uniform by the mixing effect resulting from cavity rotation and it enhances the melting rate of the ice cylinder. As the cavity‐rotating speed increases, the melting rate increases. The dimensionless melting mass is related to the Fourier number and the rotating Reynolds number in each initial condition, therefore an experimental equation that is able to quantitatively calculate the dimensionless melting mass is presented. It is seen that the melting Nusselt numbers increase again in the middle of the melting process. The ice cylinder continues to melt in spite of the small temperature difference between the ice cylinder and the solution. © 2008 Wiley Periodicals, Inc. Heat Trans Asian Res, 37(6): 359–373, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20211     

New types of magnetic domain structure in orthoferrite

Mutual interaction of domains in bubble materials causes new types of domain structure. These structures, which are observed in an orthoferrite platelet, are classified into five categories: 1) periodic bubble domains in the valleys of a wavy wall; 2) coexistence of positive and negative bubbles on both sides of a wavy wall; 3) bubbles within a ring domain; 4) concentric ring domains; and 5) coexistence of positive and negative bubbles. Experimental observations by means of magnetooptical effect were performed to investigate the stabilities, controllabilities, and physical properties of the domains. The domain structures 3), 4), 5) are stable even in zero bias field and the structures 1), 2), 3), 5) can be transferred without changing the configuration.     

Advanced evaluation of thermal ratchetting of FBR components

A new prediction method for the thermal ratchetting of a cylinder subjected to an axially moving temperature distribution is proposed in this paper. This ratchetting is quite different from the conventional Bree-type ratchetting, and an advanced evaluation method has been required in the structural design of FBR components. The proposed method considers the work hardening of actual materials for FBR components. Firstly the basic scheme of the prediction method is shown, and secondly the application procedure to the actual design is shown. Predicted results by using this method coincide well with experimental results, when compared with the case by using the previous method.     

Submicrometre X-ray printing with X-ray masks delineated by high-voltage electron-beam writing

High-voltage electron-beam writing has been successfully utilised to fabricate high-resolution and high-accuracy X-ray masks with vertical-wall gold patterns which have made it possible to print a ? ?m resist pattern without any pattern size variation across steps.     

Analysis of thermal residual stress in a thick-walled ring of duralcan-base Al-SiC functionally graded material

A ring-cutting test and an elastic theory were applied to evaluate the macroscopic residual stress in a thick-walled ring made of Al-SiC functionally graded material (FGM). The FGM ring specimens, with outer diameter 90 mm, radial thickness approximately 8.4 to 10 mm, and width 30 mm, were fabricated by the centrifugal casting method from an ingot of Duralcan F3D.20S of Al-20 vol pct SiC master composite. Because of a difference in centrifugal forces of SiC particles and of molten aluminum alloy, the rings had a graded composition of SiC particles in the radial direction. The volume fractions of SiC particles in each ring specimen varied in the range of 0 to 43 vol pct from the inner to the outer surface of the ring, depending on the applied mold spin speed. A ring diametral compression test was performed to validate an analytical formula based on the curved beam theory that can account for the graded properties of the material. Excellent agreement between the theory and the experiment was found. The residual stress was found to be generated by a cooling of Δt=140 K, which was from half the melting point corresponding stress-free condition to the ambient temperature. The hoop residual stresses in the FGM ring varied in the range of −50 to +35 MPa and from tension at the inner surface to compression at the outer surface because of the graded composition. With an increase in wall thickness and/or composition gradation, the residual stresses were found to increase.     

An experimental study of conductive heating using a concentric double-electrode applicator

With hyperthermia for treatment of superficial tumors in mind, a prototype applicator with two electrodes arranged concentrically on a disk was designed for efficient local heating, and a basic heating test was carried out. Frequencies as low as 200 kHz were used in order to simplify the configuration of the power device. The applicator consists of two electrodes, a circular inner electrode and another looped outer electrode, arranged concentrically. Water was passed through the applicator as a cooling mechanism; it was placed in direct contact with the target tissue to be heated and then charged with electricity. In the heating test using a phantom, oval hot spots were noted below the inner electrode. Using cooling water at 3 degrees C and 8.2 W, an isothermal line of 45 degrees C was located at a 5-mm radius circle around the central axis with 9 mm depth. A similar temperature distribution map was obtained in heating tests on the thigh muscle of a mongrel adult dog. The temperature distribution maps obtained from these tests corresponded closely with the results of theoretical analysis carried out according to the finite-element method. Since a comparatively low frequency was employed for this applicator the power device was simplified, which made adequate heating possible with low electric power. The temperature distribution map indicated that efficient local heating of superficial tumors could be achieved.     

Regulation of albumin mRNA and its promoter-binding nuclear factors under different perioperative nutritional methods in hepatectomized rats

BACKGROUND: Regulation of perioperative albumin synthesis under parenteral (PN) and enteral (EN) nutrition was investigated. METHODS: Rats were divided into PN and EN groups. Both groups received the same regimen of artificial nutrition for 7 days and then underwent 70% hepatectomy. Serum albumin and mRNA levels of albumin and its promoter-binding nuclear factors (C/EBPalpha, beta, and DBP) were measured. RESULTS: Serum albumin and albumin mRNA in the PN group were significantly lower than those in the EN group at 72 hours after hepatectomy. Preoperative and postoperative DBP and C/EBPalpha mRNA levels in the EN group were significantly higher than those in the PN group. CONCLUSION: Serum albumin was well maintained by EN after hepatectomy owing to an early recovery of albumin mRNA level and its nuclear factor mRNA levels (C/EBPalpha and DBP). Compared with PN, EN is a more advantageous from of perioperative nutrition as pertains to albumin synthesis.     

A study of benzylphenols as antioxidants

A series of benzylphenols has been evaluated as antioxidants for paraffin wax at 160 C. Introduction of the benzyl group to thepara- and/or ortho-positions to the hydroxyl group on the benzene ring was shown to improve antioxidative activities of phenols. Excellent activities have been observed with benzylpyrocatechols and benzyl-resorcinol. Antioxidant activities of benzylphenol compounds increased with the decrease of¹³C NMR chemical shifts (δ) of the ipsocarbon of the OH substituent.