Study on environmental effect on fatigue and creep-fatigue strength of 316FR stainless steel in sodium at elevated temperature

Low-carbon 316 stainless steel with medium-nitrogen (316FR) is considered as the principal structural material for next generation fast breeder reactor (FBR) plants in Japan. The material strength standard and the creep-fatigue life evaluation method for 316FR have been developed. However, they are based on the results of material tests in air, while actual structural material will be used mainly in liquid sodium environment in the plants. In order to clarify the environmental effect, cyclic bending tests were carried out with and without hold time in sodium. Tested materials were 316FR and conventional 304 and 316 stainless steels. Weld metal of 316FR was also tested. As a result, it was found that fatigue and creep-fatigue lives of 316FR in sodium were larger than those in air and no explicit consideration of the environmental effect is necessary in design. It was also found that the life evaluation method based on the ductility exhaustion concept is applicable to creep-fatigue life assessment in sodium.     

Scattering characteristics in reheated fluorozirconate glasses

The relation between the scattering intensity and reheating conditions in fluorozirconate glasses was studied precisely to clarify the effect of devitrification induced by fiber drawing using the preform method. The drawing-induced scattering is substantially caused by the nucleation of microcrystallites and begins to increase at a temperature lower than that predicted by DTA or DSC measurements. Nevertheless, it is revealed that ultralow-loss fluoride glass fibers can be drawn without excess loss increase by the perform method under optimized glass compositions and reheating conditions.     

Evaluation of hexabromocyclododecane in fish and marine mammal oil supplements

We analyzed the dietary fish and marine mammal oil supplements purchased from Japanese markets for hexabromocyclododecane (HBCD); 20 brands were analyzed by liquid chromatography–tandem mass spectrometry (LC/MS/MS). HBCD was detected in 15 of 22 samples, and the concentrations of all the HBCD isomers (α, β, and γ) ranged from <0.9 to 67 ng/g lipid weight. α-HBCD was the dominant residue among the HBCD isomers. However, the composition of HBCD isomers varied according to the sample type. We found that 1 sardine oil brand and 2 shark liver oil brands extracted from fish captured in seawater around Japan contained relatively high levels of HBCD, indicating that both the surface and deep seawaters around Japan may have been contaminated with HBCD.     

Present status of the High Temperature Engineering Test Reactor (HTTR)

In Japan, the research and development on the High Temperature Gas-cooled Reactors (HTGRs) had been carried out for more than fifteen years since 1969 as the multi-purpose Very High Temperature gas-cooled Reactor (VHTR) program for direct utilization of nuclear process heat such as nuclear steel making. Recently, reflecting the change of the social and energy situation and with less incentives for industries to introduce such in the near future, the JAERI changed the program to a more basic ‘HTTR program’ to establish and upgrade the HTGR technology basis.The HTTR is a test reactor with a thermal output of 30 MW and reactor outlet coolant temperature of 950°C, employing a pin-in-block type fuel block, and has the capability to demonstrate nuclear process heat utilization using an intermediate heat exchanger. Since 1986 a detailed design has been made, in which major systems and components are determined in line with the HTTR concept, paying essential considerations into the design for achieving the reactor outlet coolant temperature of 950°C. The safety review of the Government started in February 1989. By request of the Science and Technology Agency the Reactor Safety Research Association reviewed the safety evaluation guideline, general design criteria, design code and design guide for the graphite and the high-temperature structure of the HTTR.The installation permit of the HTTR was issued by the Government in November 1990.     

EVALUATION ON LIMITATION OF LINEAR ELASTIC FRACTURE MECHANICS FOR SMALL FATIGUE CRACK GROWTH

Abstract— The growth characteristics of small fatigue cracks were investigated under rotary bending in a high tensile strength steel, and the critical crack length above which linear elastic fracture mechanics (LEFM) is applicable was evaluated systematically from the results of the present study and previous studies in which two steels having different microstructures and strengths were used. It is found that the critical crack length extends over two regions each exhibiting different growth mechanisms. These regions of microstructurally small cracks and mechanically small cracks are found to be a unique function of the microstructural unit size and the yield strength of the materials, respectively. Therefore, using these relationships, it is possible to estimate the critical crack length for a given material.     

Technical evolution of permanent magnet synchronous motors for home appliances

This paper reports on the highly efficient motor technologies used in home appliances in Japan. The permanent magnet synchronous motor (PMSM) is especially suitable because the use of permanent magnets does not require any extra current to produce magnetic power in the rotor, or any other kind of energy. In Japan, there has been a rapid shift from induction motors to PMSMs, and in this paper we will show several examples of PMSMs as applied to the home appliance field. It can be seen that great improvements have been made in high‐efficiency motor technologies. Copyright © 2007 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Ultimate strength of compressed stiffened plates and minimum stiffness ratio of their stiffeners

A theoretical investigation into the effectiveness of a stiffener against the ultimate strength of a stiffened plate is carried out. Series of the buckling analyses, the elastic large deflection analyses and the elastic-plastic large deflection analyses are performed by the analytical method and the finite element method on the stiffened plate under thrust. Experiments are also carried out on the stiffened plate under thrust to confirm the theoretical results.On buckling of a stiffened plate, it is well known that ther exxists a minimum stiffness ratio of a stiffener to the plate, $\text{λ}{}^{\mathrm{B}}{}_{\min }$, which gives the maximum limiting value of the buckling strength. Concerning the ultimate strength it was confirmed that there exists a significant stiffness ratio of a st stiffener to the plate, $\text{λ}{}^{\mathrm{U}}{}_{\min }$ similar to $\text{λ}{}^{\mathrm{B}}{}_{\min }$ for the buckling strength.It was also found that there are three typical collapse modes for the stiffened plate under thrust, that is: (1) MODE OO, overall collapse after overall buckling; (2) MODE LO, overall collapse after local buckling; (3) MODE LL, local collapse after local buckling.Approximatelmethods are proposed to evaluate the ultimate strength and $\text{λ}{}^{\mathrm{U}}{}_{\min }$ of a multi-stiffened plate under thrust.The effects of initial imperfections such as welding residual stresses and initial deflection on ultimate strength and $\text{λ}{}^{\mathrm{U}}{}_{\min }$ of a stiffened plate under thrust are also discussed.     

Copolymerization of glycidylmethacrylate–methylmethacrylate–divinylbenzene in cyclohexane

The copolymerization of glycidylmethacrylate–methylmethacrylate–divinylbenzene in cyclohexane was studied as an example of crosslinking precipitation copolymerization. The resultant copolymer is fine spheroidal. The copolymerization proceeds acceleratively at first, then steadily, and gradually slows down. The larger the divinylbenzene concentration, the smaller is the copolymerization rate. Glycidylmethacrylate is preferentially incorporated in the copolymer.     

Conformational studies of poly(N-methyl-l-alanine) by n.m.r. spectroscopy

Nuclear magnetic resonance (n.m.r.) and circular dichroism of $\text{poly}\text{(N-}\text{methyl-}\text{l}\text{-alanine}\text{)}$ in methylene $\text{chloride}\text{-d}{}_2\text{dichloroacetic acid}$ were investigated. In methylene chloride-d₂$\text{poly}\text{(N-}\text{methyl-}\text{l}\text{-alanine}\text{)}$ was found to consist of nearly all-trans amide bonds and assume a stable secondary structure. Trace amounts of cis amide bonds were also present. The addition of dichloroacetic acid destroyed the secondary structure and induced a drastic change of the n.m.r. spectrum, which was similar to that observed with the monomeric amide, $\text{N-}\text{acetyl}\text{-N-}\text{methyl-}\text{l}\text{-alanine}$ dimethylamide. In comparison of the polymer with the monomeric amide, it was concluded that the transition of $\text{poly}\text{(N-}\text{methyl-}\text{l}\text{-alanine}\text{)}$ was caused by the isomerization of amide bonds. The complex n.m.r. spectrum was interpreted in terms of the distribution along the polymer chain of various non-planar amide links as well as planar cis and trans amide links. The difference of the mechanism of conformational transition between poly(amino acid) and poly(imino acid) is also discussed.