锌灰制备活性氧化锌新工艺

以炼锌厂废锌灰为原料，经硫酸浸取制备活性氧化锌，考察了工艺条件对锌浸出率的影响。实验结果表明：锌灰在50℃浸取，酸用量40g／L，可使锌的溶出率达92．8％。碱式碳酸锌最佳水解温度为40℃，水解时间为2h，pH为7．5时，溶液中锌质量浓度为10g／L，得到96％以上的水解率。采用该工艺制得的氧化锌符合HG／T2572-1994。     

Preparation and characterization of sulfonated polyetherimide/polyetherimide blend membranes

Polyetherimide (PEI) was sulfonated by chlorosulfonic acid (CSA) in 1,2‐dichloroethane for the first time. With the increase of the CSA/PEI repeat unit ratio and/or reaction time, the ion‐exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increased accordingly. Water‐uptake testing and contact‐angle measurement showed that the hydrophilicity of the SPEI increases with the increase of the IEC. Membranes were fabricated from SPEI/PEI blends with different ratios. The morphologies of the blend membranes were examined by scanning electron microscopy, which showed that the membrane pore size is larger when SPEI with higher IEC was used. With the increase of SPEI ratio in the blend membranes, the membrane pore size also increased. The contact‐angle data of the membranes showed that the hydrophilicity of the blend membrane was elevated because of the sulfonate group on the SPEI molecular backbone. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1709–1715, 2004     

微孔膜气体分布器对气液传质的影响

本文开发了一种新型微孔膜气体分布器,并对使用该分布器时鼓泡塔反应器内气液传质性能进行了研究。实验结果表明,使用这种新型膜气体分布器可以得到细小均匀的气泡,较大幅度地增大了气液传质比表面积,从而大大强化了反应器的传质能力。     

Effect of structural and electrochemical properties of different Cr-doped contents of Li[Ni1/3Mn1/3Co1/3]O2

Layered Li[Ni_(1−x)/3Mn_(1−x)/3Co_(1−x)/3Cr_x]O₂ materials with x = 0, 0.01, 0.02, 0.03, 0.05 are prepared by a solid-state pyrolysis method. The oxide compounds were calcined with various Cr-doped contents, which result in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_(1−x)/3Mn_(1−x)/3Co_(1−x)/3Cr_x]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry, and SEM. XRD experiment revealed that the Li[Ni_(1−x)/3Mn_(1−x)/3Co_(1−x)/3Cr_x]O₂ (x = 0, 0.01, 0.02, 0.03, 0.05) were crystallized to well layered -NaFeO₂ structure. The first specific discharge capacity and coulombic efficiency of the electrode of Cr-doped materials were higher than that of pristine material. When x = 0.02, the sample showed the highest first discharge capacity of 241.9 mAh g⁻¹ at a current density of 30 mA g⁻¹ in the voltage range 2.3–4.6 V, and the Cr-doped samples exhibited higher discharge capacity and better cycleability under medium and high current densities at room temperature.     

Intercalation of methylene blue in n-alkanethiolated self-assembled monolayers: Versatile electrochemical platforms for characterizing surfactant adsorption on hydrophobic surfaces

A versatile electrochemical platform for characterizing the adsorption of neutral and positively charged surfactants on hydrophobic surfaces was established using methylene blue (MB) as the probe. As a rigid, planar and electroactive species, MB can intercalate inside the regular self-assembled monolayers (SAMs) of n-hexanethiol and exhibit well-defined electrochemical responses. The adsorption of surfactants on the hydrophobic SAMs through the intercalation interaction between the hydrophobic tails of surfactants and the SAMs might change the density of the SAMs and influence the electrochemical behaviors of MB, providing a simple but effective approach for characterizing surfactant adsorption on hydrophobic surfaces. As an example, the adsorptive behaviors of cetyltrimethylammonium bromide (CTAB), a positively charged surfactant, and Triton X-100, a neutral surfactant, on hydrophobic surfaces were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The results showed that these surfactants generally experienced three different adsorptive behaviors: the monomer adsorption at low concentrations, the loose monolayer adsorption at intermediate concentrations and the dense monolayer adsorption at high concentrations. In the case of CTAB, a new additional submonolayer adsorptive behavior between the monomer and the loose monolayer adsorption was observed for the first time, due to its rather long hydrophobic tail.     

Preparation and properties of nadic‐end‐capped cyclotriphosphazene‐containing polyimide/carbon fiber composites

New novel fire‐resistant and heat‐resistant cyclotriphosphazene‐containing polyimide resins were prepared in situ by the polymerization of (p‐aminophenoxy)(phenoxy)cyclotriphosphazenes with 3,3′,4,4′‐benzophenonetetracarboxylic acid or 3,3′,4,4′‐diphenylsulfonetetracarboxylic acid and a crosslink agent, 5‐norbornene‐2,3‐dicarboxylic acid and were used as polymer matrix compositing with a woven carbon fiber to prepare nadic‐end‐capped cyclotriphosphazene‐containing polyimide/carbon fiber composites. The thermal stability, flame retardance, morphology of the surface fracture, and some physical properties of the composites were investigated by thermogravimetric analysis, scanning electron microscopy, and a material testing system, respectively. The composites had good thermal stability, flame retardance, and mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 810–818, 2003     

氯醇化管道反应新工艺的压降和传质的研究

氯醇化管道反应新工艺是环氧丙烷生产过程中关键步骤，该反应属气液非均相系统，但装有Ｋｅｎｉｃｓ型静态混合构件的管道反应器用于气液系统还缺乏大量的基础数据。研究以Ｎ２－Ｈ２Ｏ２作为实验系统，测定了不同工况下压降和氧含量，并应用一心均相模型救是了相应的摩擦系数和传质系数。     

Preparation and ionic conductivity of solid polymer electrolyte based on polyacrylonitrile‐polyethylene oxide

The transparent and flexible solid polymer electrolytes (SPEs) were fabricated from polyacrylonitrile‐polyethylene oxide (PAN‐PEO) copolymer which was synthesized by methacrylate‐headed PEO macromonomer and acrylonitrile. The formation of copolymer is confirmed by Fourier‐transform infrared spectroscopy (FTIR) measurements. The ionic conductivity was measured by alternating current (AC) impedance spectroscopy. Ionic conductivity of PAN‐PEO‐LiClO₄ complexes was investigated with various salt concentration, temperatures and molecular weight of PEO (Mn). And the maximum ionic conductivity at room temperature was measured to be 3.54 × 10^?4 S/cm with an [Li⁺]/[EO] mole ratio of about 0.1. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 461–464, 2006     

壳聚糖渗透汽化膜分离醇／水的性能：Ⅱ.壳聚糖复合膜

用聚丙烯腈超滤膜为基膜制成的ＣＳ复合膜，对乙醇／水溶液的分离具有较稳定的透过性，复合膜先后运行于低浓度的乙醇溶液的９５ｗｔ％乙醇溶液，膜的稳定性能优于均质膜。实验还表明用多种交联剂代替硫酸处理超薄复合膜，可有效地提高膜的渗透选择性。     

Synthesis, characterization and thermal properties of hexaarmed star-shaped poly(ε-caprolactone)-b-poly(d,l-lactide-co-glycolide) initiated with hydroxyl-terminated cyclotriphosphazene

Hexakis[p-(hydroxymethyl)phenoxy]cyclotriphosphazene was prepared by the reaction of hexachlorocycltriphosphaneze with the sodium salt of 4-hydroxybenzaldehyde and subsequent reduction of aldehyde groups to alcohol groups by using sodium borohydride. Hexaarmed star-shaped hydroxyl-terminated poly(ε-caprolactone) (PCL) were successfully synthesized via ring-opening polymerization of ε-caprolactone (CL) with the above hydroxyl-terminated cyclotriphosphazene initiator and stannous octoate catalyst in bulk. The number-average molecular weight of PCL linearly increased with the molar ratio of monomer to initiator. The star-shaped PCL with hydroxy end groups could be used as a macroinitiator for block copolymerization with d,l-lactide (d,l-LA) and glycolide (GA) using stannous octoate catalyst. IR, ¹H NMR and GPC analysis showed the star-block copolymers were successfully synthesized and the molecular weights and the unit composition of the star-shaped block copolymers were controlled by the molar ratios of d,l-LA and GA monomers to CL. The copolymer presented a two-phase structure, namely, PCL crystalline and d,l-LAGA amorphous domains, which made the copolymer different from linear PCL and star-shaped PCL in crystallinity and thermal behaviors.