高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

Suppression of boron penetration in p+ polysilicon gateP-MOSFETs using low-temperature gate-oxide N2O anneal

It has been reported that high-temperature (~1100°C) N₂ O-annealed oxide can block boron penetration from poly-Si gates to the silicon substrate. However, this high-temperature step may be inappropriate for the low thermal budgets required of deep-submicron ULSI MOSFETs. Low-temperature (900~950°C) N₂O-annealed gate oxide is also a good barrier to boron penetration. For the first time, the change in channel doping profile due to compensation of arsenic and boron ionized impurities was resolved using MOS C-V measurement techniques. It was found that the higher the nitrogen concentration incorporated at Si/SiO₂ interface, the more effective is the suppression of boron penetration. The experimental results also suggest that, for 60~110 Å gate oxides, a certain amount of nitrogen (~2.2%) incorporated near the Si/SiO₂ interface is essential to effectively prevent boron diffusing into the underlying silicon substrate     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

Call control and traffic transport for connection-oriented highspeed wireless personal communications over metropolitan area networks

A distributed circuit-switched approach for supporting the deployment of high speed wireless personal communication services in urban areas through the interconnection of base stations via metropolitan area networks (MANs) is proposed. Broadband MANs minimize traffic congestion by dynamic sharing of link capacity and by serving as distributed switches for partitioning call control functions. While the DQDB protocol readily supports distributed packet-switching over the IEEE 802.6 MAN, isochronous traffic such as voice and video is best supported by circuit-switched connections. The authors present an enhanced bi-state pre-arbitrated (PA) transport mechanism, and associated call control and handoff management techniques, which enable distributed circuit-switching over the MAN. These capabilities are not currently addressed in the 802.6 standards. The bi-state PA transport mechanism facilitates statistical multiplexing of variable rate isochronous traffic sources. The network capacity is constrained by the call setup delay performance, and is analyzed by simulations. Alternative signaling architectures, involving different placements of call control network elements, are evaluated. The effects of erasure nodes, and close bus versus open bus architectures, are considered. The overlap inter-MAN call setup procedure is proposed to reduce delays. Different call handoff procedures are formulated according to the type of handoff and the resulting change in call connectivity. Most handoffs are intra-MAN, requiring simple procedures with short delays     

Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry     

高扬的旗帜——博山电机厂集团股份有限公司精神文明建设纪实

建厂已近60年的博山电机厂,在企业发展的历史上曾经有过辉煌:40年代,作为军工厂,在抗日战争的烽火和解放战争的硝烟中为新中国的解放事业做出了很大的贡献;50年代,作为全国八大电机厂之一,又为新中国的建设事业提供了许多优良的产品,而且作为汽车电机、直流微电机、交流     

Variational principle of combined energy—Mechanics of laminated structures

The conventional approaches for stress analysis of composite laminates have encountered discontinuity problems. In this paper, the C¹ continuity of displacements in the in-plane directions and C⁰ continuity of displacement along the thickness direction are discussed. Also, the global continuity of transverse stresses and local continuity of in-plane stresses are examined. Then, the formulations of stress analysis in both differential equation form and variational functional form are presented.