邻二甲苯-4-磺酸从猪血粉水解液中沉淀提取L-亮氨酸的工艺

考察了pH值、邻二甲苯–4–磺酸与L–亮氨酸的物质的量比、氯化铵浓度和温度等因素对邻二甲苯–4–磺酸反应沉淀L–亮氨酸的影响。结果表明：邻二甲苯–4–磺酸沉淀L-亮氨酸的适宜pH值为不高于1.5;邻二甲苯–4–磺酸与L-亮氨酸的最适物质的量比为3∶1;溶液中氯化铵浓度增大使L–亮氨酸的沉淀率缓慢下降;温度升高L–亮氨酸的沉淀率迅速降低,反应应于低温下进行,实际生产中可选择在0 ℃。按上述最佳工艺条件从除酸后猪血粉水解液中提取L–亮氨酸,沉淀率达到90.62%,经精制L-亮氨酸产品达到《中华人民共和国药典》(2000年版二部)的标准。     

含纳米二氧化硅粒子的丙烯酯丁酯细乳化

为了调控含纳米SiO₂的丙烯酸丁酯细乳化后液滴的粒径及粒径分布,研究了细乳化体系组成和超声分散条件对细乳化液滴粒径及粒径分布的影响.发现存在使细乳化液滴粒径及粒径分布趋于稳定的临界超声功率和超声时间;随着十二烷基硫酸钠（SDS）乳化剂浓度增加,液滴粒径减小,而十六烷浓度对液滴粒径影响较小;随着BA分散液中纳米SiO₂质量分数和BA分散液/水质量比的增加,液滴平均粒径增大,粒径分布变宽,这是由于纳米SiO₂粒子吸收了部分超声波能量,同时改变了分散相特性所致.当放置或聚合温度在65℃以下时,细乳化液或相应的聚丙烯酸丁酯/纳米SiO₂复合乳胶能稳定分散.     

矿渣掺量对混凝土氯离子结合能力的影响

用等温吸附法测定了混凝土在系列氯化钠(NaCl)溶液中的平衡氯离子(Cl-)浓度,计算了矿渣混凝土对Cl-的总结合能力、物理结合能力和化学结合能力,研究了矿渣掺量对混凝土Cl-结合能力影响的规律.结果表明:在固定水胶比和胶凝材料用量的情况下,随矿渣掺量的增加,混凝土对Cl-的总结合能力和化学结合能力的变化趋势是先升后降;混凝土对Cl-的物理结合能力的影响不大.混凝土具有最大Cl-结合能力时的矿渣掺量(质量分数)为40%.     

原位乳液聚合制备的聚丙烯酸丁酯/纳米SiO2复合粒子的形貌和形成机理

通过吸附于水相分散纳米SiO2粒子表面的2,2'-偶氮(2-脒基丙烷)二氢氯化物(AIBA)的引发作用,进行丙烯酸丁酯(BA)的原位乳液聚合,制备聚丙烯酸丁酯(PBA)/纳米SiO2复合乳胶粒.分别采用透射电镜观察复合粒子的形貌,高速离心分离/超声分散和氢氟酸腐蚀表征复合胶乳中PBA乳胶粒与纳米SiO2粒子的结合程度.发现有纳米SiO2粒子聚集于复合乳胶粒表面,复合粒子表面粗糙,呈"草莓形"结构;当复合粒子中SiO2质量分率为14.6%～22.6%时,60%左右的纳米SiO2富集于复合粒子表面,30%左右被包覆在复合粒子内部,另有少量游离于水相.采用原位乳液聚合得到的复合粒子中纳米SiO2与聚合物的结合牢度远大于以AIBA为引发剂合成的PBA乳液与纳米SiO2分散液直接混合所能达到的结合牢度.认为在原位乳液聚合过程中,由于纳米SiO2粒子表面锚固的PBA量的不同,引起SiO2粒子的亲水/亲油性和与PBA的相容性也不相同,导致出现以上的SiO2的分布特性和复合粒子形貌.     

油酸修饰纳米CaCO3对PP结晶行为和力学性能的影响

Oleic acid (OA)-modified CaCO3 nanoparticles were prepared using surface modification method. Infrared spectroscopy (IR) was used to investigate the structure of the modified CaCO3 nanoparticles, and the result showed that OA attached to the surface of CaCO3 nanoparticles with the ionic bond. Effect of OA concentration on the dispersion stability of CaCO3 in heptane was also studied, and the result indicated that modified CaCO3 nanoparticles dispersed in heptane more stably than unmodified ones. The optimal proportion of OA to CaCO3 was established. The effect of modified CaCO3 nanoparticles on crystallization behavior of polypropylene (PP) was studied by means of DSC. It was found that CaCO3 significantly increased the crystallization temperature, crystal-lization degree and crystallization rate of PP, and the addition of modified CaCO3 nanoparticles can lead to the for-mation of β-crystal PP. Effect of the modified CaCO3 content on mechanical properties of PP/CaCO3 nanocompo-sites was also studied. The results showed that the modified CaCO3 can effectively improve the mechanical proper-ties of PP. In comparison with PP, the impact strength of PP/CaCO3 nanocomposites increased by about 65% and the flexural strength increased by about 20%.     

赤泥基胶凝材料的制备与性能研究

以赤泥、粉煤灰为主要胶凝材料,掺入适量激发剂(石灰)和脱硫石膏,制备了性能优异的赤泥基胶凝材料,并优化了配合比,研究了赤泥基胶凝材料的力学性能、体积稳定性和抗渗性.研究表明赤泥掺量65％,粉煤灰掺量20％,石灰掺量10％,脱硫石膏掺量5％时赤泥基胶凝材料的28 d抗压强度达到3.4 MPa,劈裂抗拉强度达到1.11 MPa.而赤泥掺量65％,粉煤灰掺量25％,石灰掺量5％,脱硫石膏掺量5％时,赤泥基胶凝材料的28 d干燥收缩为115×10-6 m,28 d温度收缩在-20～40℃ 范围内最小为40×10-6 m/℃,空气渗透系数为9.79×10-10 cm/s,抗水渗透系数为1.02×10-6 cm/s.研究表明在适量掺加石灰和脱硫石膏,有利于提高粉煤灰的水化,提高结构密实度,提高了赤泥基胶凝材料的力学性能、体积稳定性和抗渗性.     

Kinetic Treatment for copolymerization of styrene or methyl methacrylate with N-phenylmaleimide

Shirota‘s kinetic model and our kinetic model were used to treat the kinetic data of styrene (St) and N-phenylmaleimide (PMI) copolymerization in which chaxge-transfer complex (CTC) was formed. The results obtained by Shirota‘s kinetic model were disagreed with the experiments and the experimental phenomena could not be explained. The kinetic data of all feed fractions can be treated with our kinetic model, and the experimental phenomena can be explained from the propagation constants and reactivity ratios. Our kinetic model is also suitable for the kinetic data of methyl methacrylate (MMA) and PMI copolymerization in which CTC can not be formed.     

发泡剂1-一氟-1,1′-二氯乙烷在偏氯乙烯-丙烯腈-苯乙烯三元共聚树脂颗粒中的引入工艺

采用水相悬浮浸渍法制备可发泡偏氯乙烯(VDC)-丙烯腈(AN)-苯乙烯(St)三元共聚树脂颗粒,研究了体系中1-一氟-1,1′-二氯乙烷(R141b)蒸汽压对R141b分另1在水和树脂中溶解量的影响,并进行了发泡剂加入量的设计。     

邻苯二甲酸酐与环氧氯丙烷反应合成聚酯树脂

以四乙基溴化胺为催化剂,1,4-丁二醇为起始剂,邻苯二甲酸酐和环氧氯丙烷为原料合成聚酯树脂,采用傅立叶红外光谱(FT-IR)和核磁共振(1H-NMR)对产物的结构进行表征,并考察了催化剂用量和反应温度对合成聚酯树脂的影响.结果表明,合成聚酯树脂的端基为羟基,且随着温度升高和催化剂用量增加,反应速率增加,合适的反应条件为...     

注塑机肘杆式合模机构的优化分析

运用机构学方法分别对四点式和五点式斜排肘杆机构进行运动及力学性能分析,建立2种肘杆机构数学模型。借助MATLAB程序与ADAMS软件分别对2种肘杆机构进行计算和运动学仿真,并对其运动曲线进行分析。结果表明,四点斜排肘杆机构的动模板速度、加速度及机构力放大比均优于五点斜排肘杆机构,为注塑机肘杆机构的设计与选型提供了理论依据。