Modification of platinum surfaces by spontaneous deposition: Methanol oxidation electrocatalysis

The presence of a second metal on platinum surfaces affects the performance of methanol oxidation. However, most of the electrocatalytic reactions are studied by using electrochemically deposited platinum alloys, but in the case of spontaneous deposition the situation is not so clear since the surface distribution, stability and morphology are usually not well documented. The formation of surface decorated samples on mono- and poly-crystalline platinum is followed by electrochemical and spectroscopic techniques and analysis of their performance towards methanol adsorption and oxidation compared with that on pure platinum. Pt/Sn and Pt/Ru are of special interest because of their well-known performance in methanol fuel cells. Methanol oxidation on Pt(111)/Ru, Pt(111)/Sn and Pt(111) shows that ruthenium is the only one able to promote the reaction since the simultaneous dissolution of tin occurs and competes with the process of interest. The in situ infrared spectroscopy is used to compare methanol oxidation on Pt(111)/Ru and Pt(111) in acid media using p-polarized light. The formation of bridge bound carbon monoxide is inhibited in the presence of ruthenium ad-species, whereas on Pt(111) the three adsorption configurations are observed. Linear sweep polarization curves and Tafel slopes (calculated from steady state potentiostatic plots) for methanol oxidation are compared on polycrystalline surfaces modified by tin or ruthenium at different coverages. There is almost no change in the Tafel slopes due to the presence of the foreign metal except for Pt/Ru, where a 0.09 V decade⁻¹ slope was calculated below 0.55 V due to hydroxyl adsorbates on ruthenium islands. The anodic stripping of methanol residues on the three surfaces indicates a lower amount of carbon monoxide-type adsorbates on Pt/Ru, and the simultaneous tin dissolution process leading to residues oxidation on Pt/Sn electrodes.     

Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

The growth of ambient aerosols in the conditions of the respiratory system

The effect on ambient aerosols of exposure to the conditions of the respiratory system was determined by sampling simultaneously through two dichotomous samplers in parallel. In one of the samplers the aerosol was brought to 37°C and near 100% relative humidity before passing through the virtual impactor. The results show that, as a result of humidification, about 10–15% by mass of the aerosol which would normally been collected in the fine (less than 2.5 μm aerodynamic diameter) fraction of the sample grows sufficiently when humidified to be collected with the coarse fraction. It is suggested that the direct application to inhalation studies of dichotomous sampler results should be approached with some caution.     

Unsaturated polyesters. II. Structure and properties of polyester resins based on cinnamylsuccinic acid

Unsaturated Polyester resins were prepared by the reaction of cinnamylsuccinic acid with saturated diols, namely, ethylene, diethylene, propylene, dipropylene, tetramethylene, and hexamethylene glycols, and the unsaturated diols, namely, 1,4-butene- and 1,4-butynediols. All the polyester resins obtained have been characterized and were found to cure with styrene, with relatively low conversions. The properties of the cured polyesters in the form of films were determined. IR and ¹H-NMR spectroscopy were used for both qualitative and quantitative analyses of the polyesters and their hydrolyzate products, after curing with styrene.     

Experimental Procedure for Determining Transport Properties of Oxide Scales

To determine the transport properties of oxide scales growing on an alloy, a laboratory apparatus was developed which allows plotting of characteristic V = f (i) curves and oxidation with an applied electric field. The apparatus and formalism used are described; it appears that such experimental procedures allow determination of the mean ionic transport number, ti; the conductivity values σ, σ_i, and σ,_e; and the effective charge, Z*, of the moving species in the oxide scale (A1₂O₃ in the present case).     

Preparation of vanadyl porphyrin complexes from a metal-porphyrin petroleum concentrate and study of their catalytic activity

A mixture of vanadyl porphyrin complexes was obtained from a metal-porphyrin concentrate (MPC) isolated from crude petroleum by selective extraction. The petroleum MPC was subjected to demetallization and the subsequent introduction of the vanadyl cation into the porphyrin ring. It was shown that the mixture of vanadyl-porphyrin complexes obtained from MPC catalyzes the cyclohexene epoxidation reaction. On the basis of experimental data, it was assumed that the mechanism of olefin oxygenation in the presence of vanadyl porphyrin complexes is similar to the mechanism of the Prilezhaev epoxidation reaction of unsaturated compounds.     

Nanolayered lightweight flexible shields with multidirectional optical transparency

New nanolayered coatings are designed and deposited on flexible plastic substrate having the thickness of 100 /spl mu/m, in order to realize lightweight ultrathin transparent shielding foils. The structure of the coating is optimized considering three figures of merit: the average transmittance in the visible range for normal incidence, the normalized average transmittance for oblique incidence at 550 nm, and the transmittance quality factor. The nanotechnology exploited for the deposition of the transparent metals is the dual ion beam sputtering. Tests of durability, optical transmission, and shielding effectiveness demonstrate that the film has a high adhesion under mechanical solicitation, high resistance against aging, peak transmittance in the visible range higher than 70%, omnidirectional properties in the range 0/spl deg/-60/spl deg/, and shielding effectiveness of 40 dB up to 6 GHz.