Oxides Catalysts of Rare Earth and Transient Metal for Catalytic Oxidation of Benzene

The catalysts of CeO2 and the mixture of CeO2 and CuO were prepared, and the activities of these catalysts for completely oxidizing benzene were studied.The results show that the optimal proportion of CeO2/CuO is 6: 4.The highest temperature at which benzene was completely oxidized on these catalysts at different airspeed was measured.Compared these catalysts with the noble metal used, our catalysts had superiority in the resources and the industrial cost besides good activities.     

Space–Time Power Schedule for Distributed MIMO Links Without Instantaneous Channel State Information at the Transmitting Nodes

A space-time optimal power schedule for multiple distributed multiple-input multiple-output (MIMO) links without the knowledge of the instantaneous channel state information (CSI) at the transmitting nodes is proposed. A readily computable expression for the ergodic sum capacity of the MIMO links is derived. Based on this expression, which is a non-convex function of power allocation vectors, a projected gradient algorithm is developed to optimize the power allocation. For a symmetric set of MIMO links with independent identically distributed channels, it is observed that the space-time optimal power schedule reduces to a uniform isotropic power schedule when nominal interference is low, or to an orthogonal isotropic power schedule when nominal interference is high. Furthermore, the transition region between the latter two schedules is seen to be very sharp in terms of nominal interference-to-noise ratio (INR). For MIMO links with correlated channels, the corresponding space-time optimal power schedule is developed based on the knowledge of the channel correlation matrices. It is shown that the channel correlation has a great impact on the ergodic capacity and the optimality of different power scheduling approaches.     

Viterbi译码器的硬件实现

介绍了一种Vkerbi译码器的硬件实现方法。设计的基于硬判决的Viterbi译码器具有约束长度长（9)、译码深度深（64)的特点。为了兼顾硬件资源与电路性能两个方面，在设计中使用了4个ACS单元，并根据Xilinx Virtex系列FPGA的结构特点．利用FPGA内部的BlockRAM保存汉明距离和幸存路径，提高了译码速度。     

碳纳米管的制备及研究

介绍了在直流电弧放电法制备富勒烯过程中，从阴电极表面收集到大量的碳纳米管及巴基葱，产生率达到５０％，并用电子显微镜对其进行了观察和初步研究。     

Modeling and control of magnet power supply system with switch-moderipple regulator

This paper presents the dynamic performance analysis and closed-loop design of a new power supply system for a high-current magnet load. This new system introduces a series switch-mode ripple regulator (SMRR) into a phase-controlled rectifier to improve system dynamic response and to reduce the harmonic content in the magnet current. In this paper, the new system control configuration is explained. The small signal dynamic model is established. The function of the SMRR as a speed-up feed-forward path during dynamic transients is assessed. The criteria of the closed-loop regulator design are identified. The theoretical analyses are accompanied by computer simulation and experimental results. The systematical design procedure is outlined by an example which offers better performance than ever reported on high-current magnet power supplies in terms of fast dynamic response (closed-loop bandwidth several kHz) and low harmonic content (less than 10 ppm) in the magnet current     

峒室爆破CAD设计方法研究

本文对峒室爆破断面布药计算机辅助设计参数驱动方法进行了探讨围绕断面布药主要参数的变化，提出一种基于参数驱动的计算机辅助设计方法，利用ｗｉｎｄｏｗｓ操作系统下的动态数据交换特性，对断面布药进行布药参数优化，实现了交互调整布药，形成一套断面布的计算机软件，为工程爆破设计实现计算机提供了一种可行的方法。     

热释电红外摄像机斩波调制电路的设计

本文提出了热释电红外摄像机斩波调制的电路模型，并对此电路模型进行了具体的电路设计和分析。     

激光辐照对不同饵料微藻生长的影响

利用Nd:YAG激光(波长1.06μm,功率5W,照射时间0.5-3min)和Ar 激光(波长:488nm,功率70mw,照射时间5-20min)分别照射角毛藻和叉鞭金藻,辐照后进行细胞增殖和生长速率的测定。实验结果表明:照射剂量为1min的Nd:YAG激光及剂量为5min的Ar 激光对叉鞭金藻有较明显的促长效果,这两种激光处理组的细胞增殖量在辐照后的两天内较对照组分别高42.9%和48.1%,但这种促长效果随时间的推移逐渐消失。不同剂量的两种激光辐照角毛藻后,在延滞期均出现生长抑制现象,但进入指数生长期或传代培养后,剂量为1min的Nd:YAG激光及剂量为10min的Ar 激光对角毛藻有明显的促长效果,其中在指数生长期1min剂量的Nd:YAG激光处理可促长27.0%,传代培养后10min的Ar 激光处理组生长速率提高达51.2%。本文对不同激光及不同激光参数条件下,两种饵料藻的耐受性及生长特性的差异也进行分析探讨。本实验结果不仅证实了已有研究的推论,还展示出激光技术在饵料藻种选育中的应用前景。     

Turbo码中快速交织器的设计

分析了交织器在Ｔｕｒｂｏ码中的重要作用，以及目前交织器存在的缺陷，介绍了一种快速交织器的设计方法。该交织器易于实现，具有交织时延低的突出优点。计算机仿真结果表明，该快速交织器可以获得优异的性能。     

p型碲镉汞液相外延材料Ag掺杂的研究

利用SIMS和变温霍尔测量手段对P型Hg0.77Gd0.23Te液相外延材料的Ag掺杂技术、机理及掺杂碲镉汞材料的性能进行了研究。结果表明采用AgNO3溶液直接浸泡方式对该材料进行掺Ag是成功的，掺杂浓度与被掺杂材料中的汞空位浓度是一致的，掺杂后，P型碲镉汞材料的受主能级比掺杂前有明显的减小，从实验结果可看到掺Ag碲镉汞材料的电学性能在室温下保持稳定。