Transformation of the reabsorption characteristics of lignite treated by low and high temperature drying process

Abstract

The reabsorption characteristics of the lignite treated by low and high temperature drying process were addressed in the paper. The information about the moisture form, functional groups, effective water-filled porosities and equilibrium moisture content of the lignite before and after the drying process was investigated using Differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy and a self-made reabsorption device, respectively. The results show that the low drying temperature (140, 190, 230?°C, 10?min, N₂) has little impact on the effective water-filled porosities of the resulted samples, whereas it has a great influence on the main oxygen-containing functional groups, which amount firstly decreases and then increases with the drying temperature increasing. In the case of the lignite samples dried under high-temperature (600, 700, 800?°C, 30?s, N₂), the amount of the effective water-filled porosity of the sample decreases and the amount of oxygen-containing functional groups increases as the temperature increasing. The reabsorption capability of the high temperature dried sample is much lower than that of the sample treated under low drying temperature. The reabsorption characteristics of the low-temperature dried samples are affected by the amount of the oxygen-containing functional groups, while the effective water-filled porosity is main factor for the lignite samples derived from high temperature drying process. Moreover, the work gives a good evidence that the high-temperature drying process is an effective choose for lignite upgrading.     

环境监测机构实验室内部质量控制措施分析

实验室内部质量控制是发现和消除分析过程存在随机误差的重要措施.本文分析通过制定并实施质量控制计划、空白试验、校准曲线的核查、精密度控制、准确度控制、质量控制图、比对试验、密码样分析等质控措施,把实验室分析误差控制在允许范围内,以得到正确可靠的监测数据.     

1,5-己二烯交联烯烃聚合物的合成及其抗剪切稳定性

以金属配合物为催化剂、1,5-己二烯为交联剂,采用本体聚合法合成了交联超高相对分子质量烯烃类聚合物(简称交联聚合物)。用傅里叶变换红外光谱、核磁共振、凝胶渗透色潜表征交联聚合物的结构和相对分子质量。用旋转黏度计和超声波仪研究了1,5-己二烯用量对交联聚合物溶液表观黏度的影响及交联聚合物的相对分子质量对交联聚合物溶液抗剪切稳定性的影响。实验结果表明,在最佳聚合条件(单体80mL、助催化剂0．4mL、CS-1催化剂0．090g、1,5-己二烯0．40mL、0℃、24 b)下所合成的交联聚合物的重均相对分子质量为7．7×106,数均相对分子质量3．6×106。加入少量1,5-己二烯能提高交联聚合物的抗剪切能力,同时也能提高交联聚合物的相对分子质量。交联聚合物的相对分子质量越大,抗剪切稳定性越好。1,5-己二烯用量约为0．1 mL时(单体40 mL),交联聚合物溶液的表观黏度达到最大值(16．8 mPa·s)。     

水泥浆失水制约下套管与井眼间隙的研究

通过对水泥浆失水规律的室内试验分析以厦对注水泥顶替过程中水泥浆失水桥堵套管与井眼间隙问题的研究，建立了顶替过程中滤失层不发生水泥浆失水而桥堵环形空间的临界失水量计算模型，提出了调配水泥浆失水性能和确定合理套管井眼间隙的具体方法，对注水泥现场施工和井身结构设计具有一定的指导意义。     

Corrosion morphology of AZ91D exposed in an atmospheric environment

The focused ion beam technique was employed to investigate the atmospheric corrosion morphology of AZ91D. It was found that the α matrix of the alloy was preferentially corroded in the areas adjacent to intermetallic phases. The most interesting finding was that the corrosion products in corrosion cavities were pelletlike, which has never been reported before.     

Structure, properties, and thermal stability of nanocrystallite Fe-Ti-N soft magnetic films

We deposited Fe-Ti-N magnetic films with a high sputtering power of 7 W/cm/sup 2/. When the composition of the films was in the range of Fe-Ti(3.9 at.%)-N(8.8 at.%) to Fe-Ti(3.3 at.%)-N(13.5 at.%), the films were composed of /spl alpha/' and Ti/sub 2/N precipitates. With the addition of nitrogen, 4/spl pi/M/sub s/ became higher than that of pure iron, reaching a maximum of 23.8 kG. At the same time, H/sub c/ was reduced to a minimum of 1.12 Oe. The best films can meet the needs of the recording head in dual-element giant magnetoresistive/inductive heads, yielding high storage density (10 Gb/in/sup 2/). The incorporation of N in /spl alpha/-Fe brought about the /spl alpha/' phase with its higher saturation magnetization. Ti additions inhibited the equilibrium decomposition /spl alpha/'/spl rarr//spl alpha/+/spl gamma/'. Because H/sub C//sup D//spl prop/D/sup 6/, where D is average grain diameter, grain size control is very important. The nitrogen induces severe distortion of the /spl alpha/' lattice, which can cause the grains to break into pieces and reduce the grain size. High sputtering power also led to the formation of fine grains, with diameter in the order of 14 nm. Probably Ti/sub 2/N is preferentially precipitated on the grain boundary, pinning the grain boundary and stabilizing the grain size during high-temperature heat treatment. The temperature limit for stability of the structure and its associated low coercivity was not less than 520/spl deg/C.     

Analysis and optimization of DS-CDMA systems with time-limited partial response chip waveforms

Conventional direct sequence code division multiple access systems (DS-CDMA) using offset quadrature phase shift key (OQPSK) usually employ a strictly bandlimited partial response square-root raised cosine pulse as the chip waveform. They have the disadvantage of large envelope fluctuation that will incur performance degradation due to the intermodulation and bandwidth enlargement caused by post nonlinear processing. To improve the performance of DS-CDMA systems, the chip waveform and receiver should be properly selected. This paper presents a systematic performance analysis of a matched filter receiver and zero-forcing filter (ZF) receiver for DS-CDMA using a time-limited partial response chip waveform. Nevertheless the systematic performance analysis is applicable to bandlimited chip pulse as well. For the zero-forcing filters, we propose to select the frequency responses that satisfy the first Nyquist criterion. With this class of filters, we can choose the roll-off factor to minimize the total power of multiple access interference and noise power. The zero-forcing filter with proper choice of roll-off factor, referred to as optimum ZF, yields a performance better than the matched filter counterpart. The bit error rate (BER) performance of the optimum ZF with superposed quadrature amplitude modulation signal as the time pulse waveform is evaluated. It is shown that the optimum ZF provides better BER performance than conventional OQPSK and minimum shift keying, and its envelope uniformity is much better than that of OQPSK.     

低阻VDMOSFET的优化设计与制造

文章对9926型双N沟增强型VDMOSFET进行了结构和版图的优化设计。给出了该器件的纵横向结构参数,材料的物理参数和版图总体结构。单胞结构的优化设计使单胞密度达到204万个/cm2,比国际市场现有产品的单胞密度(156万个/cm2)提高了30%。这种设计采用浅n+注入工艺可使器件生产成本下降31%。最后对研制结果进行了分析讨论。     

林达大型低压甲醇合成塔在内蒙天野20万吨/年装置上的应用

简要介绍了林达均温型甲醇塔在内蒙天野20万t/a甲醇装置开车及初步运行情况。运行情况验证了该反应器的先进性,其催化剂床层测温点多、温度分布均匀、运行稳定。