Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

造纸机集散控制系统

本文介绍了造纸机集散控制系统．讨论了其硬件的组成和软件结构．研究了ＤＤＳ过程级控制器的功能及对造纸机各分部速度的优化控制．系统投人运行后，取得较好的经济效益．     

Gate and drain currents in off-state buried-type p-channel LDDMOSFETs

The buried-type p-channel LDD MOSFETs biased at high positive gate voltage exhibit novel characteristics: (1) the ratio of the drain to gate currents is about 1×10^-3 to 5×10^-3; and (2) the gate and drain currents both are functions of only the gate voltage minus the n-well bias. Such characteristics are addressed based on the formation of the surface n ⁺ inversion layer due to the punchthrough of the buried channel to the underlying shallow p-n junction. The measured gate current is due to the Fowler-Nordheim tunneling of electrons from this inversion layer surface and the holes generated within the high-field oxide constitute the drain current. The n⁺ inversion layer surface potential is found to be equal to the n-well bias plus 0.55 V. As a result, both the oxide field and the gate and drain currents are independent of drain voltage     

微重力落塔电磁悬吊、释放技术研究

论述了微重力落塔电磁悬吊、释放、提升机构的关键技术,电磁释放过程的特性分析以及微重力落塔实际试验的情况。分析说明:悬吊、释放性能的好坏决定了试验落舱的微重力水平,也是微重力落塔试验能否成功的关键技术。     

回归分析法简化钻爆设计

以某工程钻爆参数为例,阐述了在地下工程掘进施工中,应用回归分析法建立钻爆参数的相关模型,并利用此模型帮助建立某断面钻爆方案.     

倾斜水塔的爆破拆除

针对某部倾斜水塔的定向爆破拆除,从防止水塔倾倒偏移和筒体触地冲击地面对周围环境造成影响等不利情况,确定爆破方案和采取相应的防护措施.     

硼酸使掺铁铝酸锂发光增强的现象

在硼酸存在下合成了掺铁铝酸锂荧光体,研究了在不同温度下硼酸加入量对荧光体发光强度的影响,并通过X射线粉末衍射和粒度分析,初步探讨了发光增加的原因。     

The effect of pack-aluminisation on the microstructure of MCrAlY and the performance of thermal barrier coatings

Plasma spraying and pack-aluminising processes were combined and applied to the nickel-base superalloy Mar-M247 to improve its cyclic oxidation resistance. The performance tests of duplex ZrO₂-8 wt.%Y₂O₃/MCrAlY thermal barrier coatings (TBCs) were conducted at 1050 °C, 1075 °C, 1100 °C, 1150 °C and 1200 °C. The results of the experiments in this study showed that TBC specimens with the aluminised MCrAlY bond coat exhibited higher cyclic lives (except for the Ni-22Cr-10Al-1Y bond coat), at all the temperatures tested, than specimens on which the bond coat was not aluminised. The microstructures of the Co-29Cr-6Al-1Y, Co-32Ni-21Cr-8Al-0.5Y and Ni-22Cr-10Al-1Y bond coats with or without aluminising treatment were examined in detail using a scanning electron microscope equipped with an electron probe microanalyzer.     

An efficient approach for calculating the dispersions of photonic-crystal fibers: design of the nearly zero ultra-flattened dispersion

A novel and efficient approach is proposed to calculate the dispersions of the guided modes of the photonic-crystal fibers (PCFs). Based on the vector boundary-element method (VBEM), the surface integral equations for the first and second derivatives of the propagation constants with respect to the wavelength are explicitly derived. Compared with the three-point finite-difference approach, which needs to solve and search three effective indexes near the interested wavelength, this approach can determine the dispersions of the PCFs by only solving one effective index at this wavelength based on the derived formulations. This novel approach saves over 60% computing time without losing the accuracy. Based on this approach, a novel four-ring PCF is designed by optimizing only three geometrical parameters to achieve the nearly zero ultra-flattened dispersion property. Compared with previously presented dispersion-flattened PCFs, the design procedure for the four-ring structure could be more efficient and easier because relatively lesser parameters need to be optimized.