Heat extraction efficiency of a concentric glass tubular evacuated collector

The results of detailed measurements and calculations of the properties of Sydney University/Nitto Kohki evacuated collector tubes have been used to develop a formula for the instantaneous heat extraction efficiency η of a collector panel incorporating the evacuated tubes. The instantaneous efficiency depends on ambient temperature, mean fluid temperature in the collector, solar flux and the design of the manifold used to extract heat from the glass absorber tubes. Manifold design determines the mean temperature difference between absorber tube surface and mean fluid temperature for given operating conditions, and strongly affects the efficiency η of a collector panel. Neither changes in the number of evacuated tubes per unit area of collector, nor variations in solar flux, significantly alter the efficiency decrement Δ η₀ associated with a particular manifold design. Calculated efficiencies agree well with experimental results for collector panels incorporating manifolds of various designs. The formula for efficiency η allows detailed analysis of the relative importance of various energy loss mechanisms in a collector.     

从江苏苏南数字微波线路看广播电视专用网发展前景

新建微波干线电路采用高质量的数字微波设备是广电部科技工作会议的精神之一。本文介绍了江苏苏南数字微波线路，并从方案确定、技术实现、设备选型等方面进行分析比较，从而得到一个合理的整体方案。本文还着重阐述了数字传输的关键设备－编码器的现状与发展趋势，提出广播电视专用网多功能应用的设想。     

K0.9Li0.1（Ta0.5Nb0.5）O3晶体压电应变系数的测量

用准静态ｄ＿（３３）测量仪和干涉法相结合。测量了Ｋ＿（０．９）Ｌｉ＿（０．１）（Ｔａ＿（０．５）Ｎｂ＿（０．５）Ｎｂ＿（０．５））Ｏ＿３晶体的压电应变系数。结果为：ｄ＿（３３）＝８６．０，ｄ＿（３３）＝一２９．５，ｄ＿（１５）＝１１２．９×１０￣（－１２）Ｃ／Ｎ．     

宝钢钢管IPSEN炉炉温调节仪表的改造

在宝钢钢管调质炉(IPSEN炉)控制系统的改造中,用西门子S7-400的PID功能软件模块改造原模拟调节器,以实现加热调质温度控制.介绍了用S7-400的PID控制模块构成淬火炉、淬火油槽、回火炉温度控制的方法,并由此提出对宝钢钢管生产中其它加热炉控制系统改造的选择方案.     

硼酸使掺铁铝酸锂发光增强的现象

在硼酸存在下合成了掺铁铝酸锂荧光体,研究了在不同温度下硼酸加入量对荧光体发光强度的影响,并通过X射线粉末衍射和粒度分析,初步探讨了发光增加的原因。     

转炉负能炼钢攻关对策

通过介绍转炉炼钢工艺流程及工序能耗分析，为提高转炉煤气回收量及降低电耗采取了一系列攻关措施，实现了转炉负能炼钢，取得了一定经济效益。     

Nucleotide sequence and genome structure of mink enteritis virus

Diabetes mellitus is a common disease. It affects multiple organ systems. Adverse effects of hyperglycemia on infection, fracture healing, and bone remodeling have been recently reported. This study was conducted to evaluate the clinical and radiographic results of 93 total hip arthroplasties in 78 consecutive patients with diabetes. All femoral components were cemented using contemporary cementing techniques. Prophylactic antibiotics were given in each case. The mean follow-up period was 4.1 years (range, 2-6.5 years). Ninety-six percent of the hips were rated excellent or good. Radiolucencies were observed in only 3.7% of the stems, while 22.2% of the cups showed radiolucencies. There was a 4% revision incidence. There was no postoperative infection in this series--a distinct improvement from previously reported series. However, complications remained high at 24.3%. The most frequent complication was urinary tract infection (14.2%). The most serious complication was myocardial infarction. The authors believe total hip arthroplasty can be safely performed in patients with diabetes, provided that adequate medical and follow-up evaluations are performed. The medium-term clinical and radiographic follow-up evaluations are not inferior to reported series in patients without diabetes.     

Epoxidation of high trans‐1,4‐polyisoprene and its properties

A new organic‐solvent‐free water‐phase suspension method was used to synthesize partially epoxidized high trans‐1,4‐polyisoprene (TPI) to improve its properties, including oil resistance and wet‐skid resistance. The epoxidation was conducted in an aqueous peracetic acid solution and on the TPI granules prepared by a bulk precipitation method with supported titanium catalyst. The effects of the synthesis conditions, including reaction temperature, reaction time, and pH value, on the epoxy content were investigated. Epoxidized trans‐1,4‐polyisoprene (ETPI) with epoxy contents between 10 and 80% were obtained within 4 h. Both the amorphous and crystalline regions of TPI were epoxidized. The crystallization properties decreased with increasing epoxy content. ETPIs possessed lower mechanical properties than TPI but could be enhanced by vulcanization. The oil resistance and wet‐skid resistance were significantly improved after epoxidation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dual band-notched ultra-wideband microstrip antenna using asymmetrical spurlines

A simple and novel ultra-wideband microstrip-fed antenna with dual band-notched characteristic is presented. By etching a pair of asymmetrical spurlines on the feedline, two notched bands of 600 MHz (3.95? 4.55 GHz) and 650 MHz (5.35?6.0 GHz) are achieved. Measured results show that this antenna operates from 2.5 to 12.0 GHz for voltage standing wave ratio less than 2, except two frequency notched bands of 3.95?4.55 GHz and 5.35?6.0 GHz. Moreover, this antenna has good omnidirectional radiation patterns in the H-plane.