陕南山地烟田不同植烟年限土壤养分的变化

为给陕南山地烟草生产布局及有针对性的施肥措施提供依据,分析了陕南山地烟田不同植烟年限(0~15年)与土壤养分含量的关系。结果表明:随着植烟年限延长,有机质线性下降,全氮和速效钾显著上升,有效磷先上升后下降;氯、有效铁、有效锰、有效硼和有效铜无显著变化或变化很小,有效锌则在第1年急剧下降,之后保持稳定,10年后再次显著下降。认为陕南山地烟区烟叶生产中应适当增加有机肥的施用而合理控制氮肥、磷肥和钾肥的施用,并要注意锌肥的补充。     

Two-step pyrolytic engineering to form porous nitrogen-rich carbons with a 3D network structure for Zn-air battery oxygen reduction electrocatalysis

It is of great urgency to design inexpensive and high-performance oxygen reduction reaction (ORR) electrocatalysts derived from biowastes as substitutes for Pt-based materials in electrochemical energy-conversion devices. Here we propose a strategy to synthesize three-dimensional (3D) porous nitrogen-doped network carbons to catalyze the ORR from two-step pyrolysis engineering of biowaste scale combined with the use of a ZnCl₂ activator and a FeCl₂ promotor. Electrochemical tests show that the synthesized network carbons have exhibited comparable ORR catalytic activity with a half-wave potential (~0.85 V vs. RHE) and outstanding cyclical stability in comparison to the Pt/C catalyst. Beyond that, a high electron transfer number (~3.8) and a low peroxide yield (<7.6%) can be obtained, indicating a four-electron reaction pathway. The maximum power density is ~68 mW cm^?2, but continuous discharge curves (at a constant potential of ~1.30 V) for 12 h are not obviously declined in Zn-air battery tests using synthesized network carbons as the cathodic catalyst. The formation of 3D porous structures with high BET surface area can effectively expose the surface catalytic sites and promote mass transportation to boost the ORR activity. This work may open a new idea to prepare porous carbon-based catalysts for some important reactions in new energy devices.     

餐饮废油生物柴油低温流动性的改进研究

使用气-质联用仪测定餐饮废油生物柴油(WCME)和-10号柴油(-10PD)的组成,使用冷滤点试验器和运动黏度试验器测定WCME的低温流动性,同时使用调合、添加低温流动性改进剂的方法改进WCME的低温流动性。实验结果表明,WCME主要由饱和脂肪酸甲酯和不饱和脂肪酸甲酯组成,质量分数分别为27.63%和71.81%;WCME冷滤点为0℃,运动黏度(40℃)为4.41mm2/s;WCME与-10PD调合后,冷滤点降低,其中B20的冷滤点最低,为-13℃,运动黏度随着WCME的体积分数的减少,逐渐接近-10PD的运动黏度。通过添加低温流动性改进剂,WCME,B10,B20的冷滤点分别从0,-8,-13℃降至-4,-26,-25℃。     

Accelerated multi-contrast high isotropic resolution 3D intracranial vessel wall MRI using a tailored k-space undersampling and partially parallel reconstruction strategy

Objective

To develop a 3D multi-contrast IVW protocol with 0.5-mm isotropic resolution and a scan time of 5 min per sequence.

Materials and methods

Pre-contrast T1w VISTA, DANTE prepared PDw VISTA, SNAP, and post-contrast T1w VISTA were accelerated using cartesian undersampling with target ordering method (CUSTOM) and self-supporting tailored k-space estimation for parallel imaging reconstruction (STEP). CUSTOM + STEP IVW was compared to full-sample IVW, SENSE-accelerated IVW, and CUSTOM + zero-filled Fourier reconstruction in normal volunteers and subjects with intracranial atherosclerotic disease (ICAD). Image quality, vessel delineation, CSF suppression, and blood suppression were compared.

Results

CUSTOM + STEP vessel wall delineation was comparable to full-sample IVW and better than SENSE IVW for vessel wall delineation on T1w VISTA and luminal contrast on SNAP. Average image quality and wall depiction were significantly improved using STEP reconstruction compared with zero-filled Fourier reconstruction, with no significant difference in CSF or blood suppression.

Conclusions

CUSTOM + STEP allowed multi-contrast 3D 0.5-mm isotropic IVW within 30 min. Although some quantitative and qualitative scores for CUSTOM − STEP were lower than fully sampled IVW, CUSTOM + STEP provided comparable vessel wall delineation as full-sample IVW and was superior to SENSE. CUSTOM + STEP IVW was well tolerated by patients and showed good delineation of ICAD plaque.

     

Fabrication of hierarchical PANI@W-type barium hexaferrite composites for highly efficient microwave absorption

Hexagonal barium ferries is a promising and efficient microwave (MW) absorbing material, but the low dielectric loss and poor conductivity have limited their extensive applications. In this work, a simple tactic of coating conductive polymer PANI on hexaferrite BaCo₂Fe₁₆O₂₇ is presented, wherein the dielectric properties are customized, and more significantly, the electromagnetic loss is greatly enhanced. As displayed from structural characterizations, PANI were coated equably on the surface of hexaferrite grains by an in-situ polymerization process. The outcomes exhibit the as-prepared PANI@hexaferrite composite has remarkable electromagnetic wave absorption capacity. When the thickness is 6.0 mm, the minimal RL of ?40.4 dB was achieved at 2.9 GHz. The effective absorption bandwidth (RL < ?20 dB) of 0.65 GHz, 0.53 GHz, 0.65 GHz, 0.52 GHz, 0.46 GHz and 0.39 GHz was achieved separately when the thickness ranges from 4 to 9 mm. The highly efficient MW absorbing performance of PANI@hexaferrite composite were the consequence of multiple loss mechanisms and perfect impedance matching. It is demonstrated that the PANI@hexaferrite composite with excellent MW absorption performance is expected to be potential MW absorbers for extensive applications.     

Fabrication of direct Z-scheme FeIn2S4/Bi2WO6 hierarchical heterostructures with enhanced photocatalytic activity for tetracycline hydrochloride photodagradation

A series of direct Z-scheme FeIn₂S₄/Bi₂WO₆ hierarchical heterostructures with intimate interface contacts were synthesized by in-situ growth route and characterized by systematical analyses. All as-prepared FeIn₂S₄/Bi₂WO₆ nanocomposites showed significantly enhanced photocatalytic activity towards photodegradation for the removal of tetracycline hydrochloride (TCH) in comparison with individual FeIn₂S₄ and Bi₂WO₆. Meanwhile, the highest photocatalytic degradation activity can be achieved by modulating adding amount of FeIn₂S₄ in FeIn₂S₄/Bi₂WO₆ nanocomposites and the optimized component ratio of FeIn₂S₄ to Bi₂WO₆ is determined to be 10 wt%. The enhanced photocatalytic activity could be ascribed to efficient separation between photogenerated holes and electrons based on the construction of direct Z-scheme system. The high photocatalytic stability of resultant 10 wt% FeIn₂S₄/Bi₂WO₆ nanocomposites was revealed through six successive recycling reactions. The main intermediate generated during TCH photodegradation was explored by HPLC-MS. Besides, the direct Z-scheme photocatalytic mechanism was confirmed by band position analysis, electron spin resonance (ESR) and active species capture experiment.     

Software assurance practices for mobile applications

Mobile software applications have to cope with a particular environment that involves small size, limited resources, high autonomy requirements, competitive business models and many other challenges. To provide development guidelines that respond to these needs, several practices have been introduced; however, it is not clear how these guidelines may contribute to solve the issues present in the mobile domain. Furthermore, the rapid evolution of the mobile ecosystem challenges many of the premises upon which the proposed practices were designed. In this paper, we present a survey of the literature on software assurance practices for mobile applications, with the objective of describing them and assessing their contribution and success. We identified, organized and reviewed a body of research that spans in three levels: software development processes, software product assurance practices, and software implementation practices. By carrying out this literature survey, we reviewed the different approaches that researchers on Software Engineering have provided to address the needs that raise in the mobile software development arena. Moreover, we review the evolution of these practices, identifying how the constant changes and modernization of the mobile execution environment has impacted the methods proposed in the literature. Finally, we introduced discussion on the application of these practices in a real productive setting, opening an area for further research that may determine if practitioners have followed the proposed assurance paradigms.     

Intrinsic CFRP-metal-hybrids with rubber interface for the improvement of the damping behaviour

This paper presents an integrated passive damping approach in hybrid metal-CFRP parts for structural applications. In this concept a viscoelastic material is embedded in the joint zone of the hybrid component. To examine the connection strength single-lap-joint specimens were produced and tested and the influence of the used material combinations, different surface structures, and different process parameters i.e. the moment of cross-linking were evaluated. Afterwards, the metal-CFRP hybrids were tested in quasi-static tests to assess their connection strength and failure behaviour. Dynamic cyclic tensile tests with step-wise increased loading conditions were performed to determine the specimens damping behaviour and to estimate their fatigue performance. Finally, these results are compared to a state of the art metal-CFRP hybrid with rivets connecting both materials.     

On stochastic comparisons of finite mixtures for some semiparametric families of distributions

In this paper, we consider the classical finite mixture model, which is an effective tool for modeling lifetime distributions for random samples from heterogeneous populations. We discuss new results on stochastic comparison for two finite mixtures when each of them is drawn from one of the following semiparametric families, i.e., proportional hazards, accelerated lifetime and proportional reversed hazards.